Advertisement
Quick Links
Made in America
Thank you for purchasing this instrument from Intellitronix. We value our customers!
* Always disconnect the battery before attempting any electrical work on your vehicle. *
KIT COMPONENTS
One (1) Digital Circuit Board (with Speedometer, Tachometer, Fuel, Voltmeter,
Water Temp, Oil Pressure Gauges)
One (1) Smoked Acrylic Lens
One (1) Cutout Black Film Overlay
One (1) Temperature Sending Unit (S8013) - 1/8" NPT, 0-255 Deg., 3/8" NPT Bushing
One (1) Pressure Sending Unit (S8868) - 1/8" NPT, 0-100 PSI Oil Pressure
One (1) Ford Speedometer Sensor (S9024)
One (1) Mounting Kit to Include:
• Six (6) #6 x 1" Nylon Spacers
• Five (5) #6 x 2" Flat Head Machine
Screw
• One (1) #6 x 1 ½" Pan Head Screw
See Figure 2 for
all 5 smaller
cirecles
Page | 1 DP7006
INSTALLATION GUIDE
Ford Fox Body Mustang
Part Number: DP7006
Year Series: 1979-1986
* Peel off protective covering from both sides *
2/27/2024
Lifetime Guarantee
• One (1) #6 x 1" Flat Head Machine
Screw
• Six (6) #6 x 5/16" Nylon Spacers
• One (1) #6 Nylock Nut
See Figure 1
www.intellitronix.com
Advertisement
Related Manuals for Intellitronix DP7006
Summary of Contents for Intellitronix DP7006
- Page 1 Made in America Lifetime Guarantee Thank you for purchasing this instrument from Intellitronix. We value our customers! INSTALLATION GUIDE Ford Fox Body Mustang Part Number: DP7006 Year Series: 1979-1986 * Always disconnect the battery before attempting any electrical work on your vehicle. *...
- Page 2 Black/White Ground to speed sender Brown High Beam Purple Dimmer Brake Brown/Yellow Boost or 4X4 Grey with push button Speedometer/Tachometer Orange/White Corvette board only Oil Temperature Red/white corvette board only Ground for oil temp Page | 2 DP7006 2/27/2024 www.intellitronix.com...
-
Page 3: Wiring Instructions
If using a wire from an external harness, make sure that the wire does not have power. Fuel senders reference their ground from the sender mounting plate. Connect the yellow wire to the factory sending unit. Page | 3 DP7006 2/27/2024 www.intellitronix.com... - Page 4 Vehicle vin or Model and year and Consult your factory Pinout Chart. Speedometer - White (Intellitronix Speed Sender to replace factory cable drive) - Disconnect the mechanical speedometer cable from the transmission and insert the new electronic sensor into the transmission.
-
Page 5: Trip Distance
Note: If doing a LS engine swap, pick up the tach signal wire from the ECM/ECU and then set the tach switch to 4-cylinders. You will also need the Intellitronix LS Engine Swap Adapter Kit for Series 1, 2 and 3 engines. -
Page 6: Setting The Odometer
Warning: If the microprocessor does not receive any data, the unit will display ‘Err” and will revert to the factory settings. This can be the result of not moving the vehicle while in ‘CAL’ mode or the dash is not receiving a proper speed signal from the vehicle. Page | 6 DP7006 2/27/2024 www.intellitronix.com... - Page 7 The odometer will continue to display the pulse reading for a few seconds. Once it reverts to the default mode, you have successfully calibrated your speedometer. Page | 7 DP7006 2/27/2024 www.intellitronix.com...
Need help?
Do you have a question about the DP7006 and is the answer not in the manual?
Questions and answers