HP J4850A Installation And Getting Started Manual

Procurve series 5300xl switches.
Hide thumbs

Advertisement

ProCurve Series
5300xl Switches
PoE
Power over Ethernet Devices
www.procurve.com
Installation and
Getting Started Guide

Advertisement

   Related Manuals for HP J4850A

   Summary of Contents for HP J4850A

  • Page 1

    Installation and Getting Started Guide ProCurve Series 5300xl Switches Power over Ethernet Devices www.procurve.com...

  • Page 3

    ProCurve Switch 5300xl Series Installation and Getting Started Guide...

  • Page 4

    © Copyright 2001, 2005 - 2007 Hewlett-Packard Development Disclaimer Company, L.P. HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not...

  • Page 5: Table Of Contents

    Contents 1 Introducing the ProCurve Switch 5300xl Series Front of the Switch ..........1-4 LEDs .

  • Page 6: Table Of Contents

    8. (Optional) Connect a Console to the Switch ....2-19 Terminal Configuration ........2-19 Direct Console Access .

  • Page 7: Table Of Contents

    Testing the Switch by Resetting It ......4-10 Checking the Switch LEDs ....... 4-10 Checking Console Messages .

  • Page 8: Table Of Contents

    Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection ..... B-7 Cable Diagram ......... B-7 Pin Assignments .

  • Page 9

    Switch operation overview Switch 5304xl, Switch 5348xl and the Switch 5304xl-32G. The Switch 5304xl is available as an open 4-slot chassis (J4850A), as the Switch 5348xl bundle (J4849B) with two 24-port 10/100-TX xl Modules pre-installed, and as the Switch 5304xl-32G (J8166A) with two 16-port 100/1000-T xl Modules pre- installed.

  • Page 10

    Introducing the ProCurve Switch 5300xl Series ProCurve Switch 5304xl-32G bundle (J8166A) with two 16 port 100/1000-T xl Modules preinstalled Figure 1-2. Example 5304-32G bundle Switch 5308xl and Switch 5372xl and the Switch 5308xl-48G. The Switch 5308xl is available as an open 8-slot chassis (J4819A), as the Switch 5372xl bundle (J4848B) with three 24-port 10/100-TX xl Modules pre-installed and as the Switch 5308xl-48G bundle (J8167A) with three 16-port 100/1000-T xl Modules pre-installed.

  • Page 11

    Introducing the ProCurve Switch 5300xl Series ProCurve Switch 5372xl bundle (J4848B) with three 10/100-TX xl Modules preinstalled Figure 1-4. Example 5372xl bundle ProCurve Switch 5308xl-48G bundle (J8167A) with three 100/1000-T xl Modules preinstalled Figure 1-5. Example 5308xl-48G bundle See “Switch Features” on page 1-10 for a list of the switch modules that you can install in the ProCurve Switch 5300xl Series (modules available when this...

  • Page 12: Front Of The Switch

    Introducing the ProCurve Switch 5300xl Series Front of the Switch Front of the Switch Status LEDs for the Fans, Power Supplies, Console and Switch Modules Port Power Reset and Clear LED Mode Select button and Fault buttons and indicator LEDs LEDs Self Test LED Switch Modules and slots...

  • Page 13: Leds

    Introducing the ProCurve Switch 5300xl Series Front of the Switch LEDs As described in the next two tables, there are LEDs on the switch chassis and on the switch modules that keep you informed of the status of the switch and the network connections.

  • Page 14

    Introducing the ProCurve Switch 5300xl Series Front of the Switch LEDs State Meaning Status/ A module is installed in the switch module slot corresponding to the letter and the module Modules is undergoing or has passed self test. This also occurs when you install a module when (green - letters the switch is already powered on (“hot swap”).

  • Page 15: Led Mode Select Button And Indicator Leds

    Introducing the ProCurve Switch 5300xl Series Front of the Switch LED Mode Select Button and Indicator LEDs To optimize the amount of information that can be displayed for each of the switch ports, the Switch 5300xl Series use a Mode LED for each port. The operation of this LED is controlled by the LED Mode Select button on the switch chassis, and the current selection is indicated by the mode indicator LEDs near the button.

  • Page 16: Console Port, Reset Button, Clear Button

    Introducing the ProCurve Switch 5300xl Series Front of the Switch Console Port This port is used to connect a console to the switch by using the serial cable supplied with the switch. This connection is described under “Connecting a Console to the Switch” in chapter 2, “Installing the Switch 5300xl Series”. The console is a full-featured interface that can be used to configure, monitor, and troubleshoot the switch.

  • Page 17: Back Of The Switch, Power Connector, Slot For Redundant Power Supply

    Introducing the ProCurve Switch 5300xl Series Back of the Switch Back of the Switch slot for installing optional AC power connector redundant power supply pull strap Figure 1-8. Example back of 5300xl Series Power Connector The Switch 5300xl Series do not have a power switch; they are powered on when connected to an active AC power source.

  • Page 18: Switch Features

    Introducing the ProCurve Switch 5300xl Series Switch Features Switch Features The features of the Switch 5300xl Series include: 4 or 8 slots for installing any of the available Switch xl Modules. ■ Supported Modules: As of this printing, the supported xl modules includes: •...

  • Page 19

    Introducing the ProCurve Switch 5300xl Series Switch Features ■ the modules can be installed in any order and in any combination and can be “hot swapped”. the supported mini-GBICs can be hot swapped into the mini-GBIC xl ■ Module. ■ the supported transceivers can be hot swapped into the 10-GbE vl Module.

  • Page 21: Included Parts

    Installing the Switch 5300xl Series The Switch 5300xl Series is easily installed. They come with an accessory kit that includes the brackets for mounting the switch in a standard 19-inch telco rack, in an equipment cabinet, or on a wall. The switches have rubber feet already attached so they can be securely located on a horizontal surface.

  • Page 22

    Installing the Switch 5300xl Series Included Parts Power cord, one of the following: ■ Australia/New Zealand 8120-6803 China 8120-8377 Continental Europe 8120-6802 Denmark 8120-6806 Japan 8121-0606 Switzerland 8120-6807 United Kingdom/ Hong Kong/Singapore 8120-8709 United States/Canada/ Mexico 8121-0605 J a p a n P o w e r C o r d W a r n i n g...

  • Page 23: Installation Procedures, Summary

    Installing the Switch 5300xl Series Installation Procedures Installation Procedures Summary Follow these easy steps to install your switch. The rest of this chapter provides details on these steps. Prepare the installation site (page 2-6). Make sure that the physical environment into which you will be installing the switch is properly prepared including having the correct network cabling ready to connect to the switch, and having a good location for the switch.

  • Page 24: Installation Precautions

    Installing the Switch 5300xl Series Installation Procedures Connect the network devices (page 2-18). Using the appropriate network cables, connect other switches, hubs, routers, computers, servers, printers, and other network devices to the switch ports. For more information, see “Connect the Network Devices” on page 2-18.

  • Page 25

    Installing the Switch 5300xl Series Installation Procedures Installation Precautions (continued) C a u t i o n s ■ Ensure the power source circuits are properly grounded, then use the power cord supplied with the switch to connect it to the power source. If your installation requires a different power cord than the one supplied with the switch and power supply, be sure the cord is adequately sized for the switch’s current requirements.

  • Page 26: Prepare The Installation Site, Cabling Infrastructure

    Installing the Switch 5300xl Series Installation Procedures 1. Prepare the Installation Site Cabling Infrastructure Ensure the cabling infrastructure meets the necessary network specifications. See the following table for cable types and lengths, and see appendix B, “Switch Ports and Network Cables” on page B-1 for more information: Table 2-1.

  • Page 27: Installation Location

    Installing the Switch 5300xl Series Installation Procedures Port Type Cable Type Length Limits 62.5 μm cable: ■ 10-GbE SR Multimode fiber-optic cable designed for Gigabit Ethernet: 62.5/125 μm (core/cladding) • 160 Mhz/km = 2-26 meters diameter or 50/125 μm, low metal content, •...

  • Page 28: Install Switch Xl Modules

    Installing the Switch 5300xl Series Installation Procedures 2. Install Switch xl Modules Install switch modules into the slots as shown in the illustration below. For installation details, see the instructions in the manual that comes with the module. C a u t i o n Make sure you install only ProCurve Switch xl Modules.

  • Page 29

    Installing the Switch 5300xl Series Installation Procedures insert module into the guides and slide it in until “Low-force” connector. it is fully inserted. High insertion force is not needed and should not be used. Figure 2-1. Installing a module the module is fully inserted when the module bulkhead is contacting, or very close to contacting the face of the switch.

  • Page 30: Optional) Install Second Power Supply

    Installing the Switch 5300xl Series Installation Procedures 3. (Optional) Install Second Power Supply A second, load-sharing redundant power supply (ProCurve Switch gl/xl/vl RPS, J4839A) can be installed in the back of the switch. To provide true redundancy, this second power supply should be connected to a different AC power source from the other supply.

  • Page 31

    Installing the Switch 5300xl Series Installation Procedures Insert the power supply into the opening, then slide it all the way in until it connects to the switch. The power supply face plate will be flush with the back face of the switch.

  • Page 32: Verify The Switch Passes Self Test

    Installing the Switch 5300xl Series Installation Procedures 4. Verify the Switch Passes Self Test After you have installed any modules and the optional second power supply, but before mounting the switch in its network location, you should first verify it is working properly by plugging it into a power source and verifying it passes its self test.

  • Page 33: Led Behavior:

    Installing the Switch 5300xl Series Installation Procedures switch chassis LEDs switch module LEDs: Link and Mode LEDs for each port Figure 2-6. Switch LEDs When the switch is powered on, it performs its diagnostic self test. The entire download, initialization, and self test process can take up to 2 minutes for a fully loaded chassis, depending on the number and type of modules installed in the switch.

  • Page 34: Mount The Switch, Rack Or Cabinet Mounting

    Installing the Switch 5300xl Series Installation Procedures 5. Mount the Switch After the modules and optional power supply are installed and you have verified the switch passes self test, you are ready to mount the switch in a stable location. The Switch 5300xl Series can be mounted in these ways: in a rack or cabinet ■...

  • Page 35

    Installing the Switch 5300xl Series Installation Procedures Partially install a screw (5/8-inch number 12-24) into the top hole of a pair of holes that are 0.5 inches apart in each rack/cabinet upright as shown in the illustration below. Ensure that the screws are at the same level in each upright.

  • Page 36: Horizontal Surface Mounting

    Installing the Switch 5300xl Series Installation Procedures Install the other number 12-24 screw into the upper hole in each bracket. Tighten these screws. install and tighten the other 12-24 screws Figure 2-10. Installing the final rack mounting screw E q u i p m e n t If you are installing the switch in an equipment cabinet, in place of the C a b i n e t 12-24 screws supplied with the switch, use the clips and screws that came with...

  • Page 37: Wall Mounting

    Installing the Switch 5300xl Series Installation Procedures Wall Mounting The mounting brackets supplied with the switch allow you to mount it on a wall. The illustrations below show mounting a Switch 5308xl/5372xl. The Switch 5304xl/5348xl would be mounted in a similar way. C a u t i o n For safe operation, do not install the switch with the vents or fans facing downward.

  • Page 38: Connect The Switch To A Power Source, Connect The Network Devices

    Installing the Switch 5300xl Series Installation Procedures 6. Connect the Switch to a Power Source Plug the included power cord into the switch’s power connector and into a nearby properly grounded AC power source. If you have installed a redundant power supply module into the switch, it should be connected to a separate AC power source.

  • Page 39: Optional) Connect A Console To The Switch, Terminal Configuration

    Installing the Switch 5300xl Series Installation Procedures 8. (Optional) Connect a Console to the Switch The Switch 5300xl Series have a full-featured, easy to use console interface for performing the following tasks: Monitor switch and port status and observe network activity counters ■...

  • Page 40: Direct Console Access, Telnet Console Access

    Installing the Switch 5300xl Series Installation Procedures If you want to operate the console using a different configuration, ensure you change the settings on both the terminal and on the switch. Change the switch settings first, then change the terminal settings, and reestablish the console session.

  • Page 41: Hot Swapping Switch Modules, Adding Or Replacing Modules, Changing The Module Type

    Installing the Switch 5300xl Series Hot Swapping Switch Modules If you want to continue with console management of the switch at this time through either a direct connection or a telnet session, see chapter 3, “Getting Started With Switch Configuration” for some basic configuration steps. For more detailed information, refer to the Management and Configuration Guide which is on the ProCurve Web site, www.procurve.com.

  • Page 42: Example Network Topologies, Basic Connectivity

    Installing the Switch 5300xl Series Example Network Topologies Example Network Topologies This section shows you a few example network topologies in which the Switch 5300xl Series can be implemented. For more topology information, see the ProCurve Networking Web site, www.procurve.com. Basic Connectivity server connected by a Gigabit link...

  • Page 43: Use As An Edge Switch

    Installing the Switch 5300xl Series Example Network Topologies Use as an Edge Switch trunked ProCurve redundant Gigabit Routing Switch 9308 fiber-optic cables switch 5300xl Figure 2-15. Using the 5300 Series on the Edge When your network expands and the users need to access resources beyond the edge of the local network, the Switch 5300xl Series are excellent platforms for that expansion.

  • Page 44

    Installing the Switch 5300xl Series Example Network Topologies This example configuration shows connectivity using a Switch Access Controller xl Module (J8162A) as a 720 access controller for a wireless network. Remember the Access Controller xl Module must be connected to an access control server (either a ProCurve Access Control Server 740wl or a ProCurve Integrated Access Manager 760wl).

  • Page 45

    Installing the Switch 5300xl Series Example Network Topologies Used as an Aggregation Switch switch 5300xl switch 5300xl switch 5300xl switch 5300xl switch 5300xl switch 8212zl Figure 2-17. 10-GbE Aggregation Topology The J8988A module in the Switch 5300xl Series will provide customers with a 10-GbE uplink connection (expected throughput is 2.5 to 7 Gbps, depending on packet size).

  • Page 47: Recommended Minimal Configuration

    Getting Started With Switch Configuration This chapter is a guide for using the console Switch Setup screen to quickly assign an IP (Internet Protocol) address and subnet mask to the switch, set a Manager password, and, optionally, configure other basic features. For more information on using the switch console and the other switch management interfaces: the web browser interface and the SNMP manage- ment tool, ProCurve Manager, please see the Management and Configuration...

  • Page 48: Using The Switch Setup Screen

    Getting Started With Switch Configuration N o t e By default, the switch is configured to acquire an IP address configuration from a DHCP or Bootp server. To use DHCP/Bootp instead of the manual method described in this chapter, see “DHCP/Bootp Operation” in the Management and Configuration Guide which is on the ProCurve Web site, www.procurve.com.

  • Page 49

    Getting Started With Switch Configuration Tab to the IP Config (DHCP/Bootp) field and use the Space bar to select the Manual option. Tab to the IP Address field and enter the IP address that is compatible with your network. Tab to the Subnet Mask field and enter the subnet mask used for your network.

  • Page 50: Where To Go From Here

    Getting Started With Switch Configuration Where to Go From Here The above procedure configures your switch with a Manager password, IP address, and subnet mask. As a result, with the proper network connections, you can now manage the switch from a PC equipped with Telnet, a web browser interface, or from an SNMP-based network management station using a tool such as ProCurve Manager.

  • Page 51: Using The Ip Address For Remote Switch Management, Starting A Telnet Session

    Getting Started With Switch Configuration Using the IP Address for Remote Switch Management Using the IP Address for Remote Switch Management With your Switch 5300xl Series, you can use the switch’s IP address to manage the switch from any PC that is on the same subnet as the switch. You can use either a Telnet session or a standard web browser to manage the switch.

  • Page 52

    Getting Started With Switch Configuration Using the IP Address for Remote Switch Management For more information on using the web browser interface, please see the Management and Configuration Guide which is on the ProCurve Web site, www.procurve.com. An extensive help system is also available for the web browser interface. To access the help system though, the subnet on which the switch is installed must have access to the internet, or ProCurve Manager needs to be installed on a network management station that is on the subnet.

  • Page 53: Configuring The Procurve Access Controller Xl Module (j8162a), Wl/760wl Configuration, Module Configuration

    Getting Started With Switch Configuration Configuring the ProCurve Access Controller xl Module (J8162A) Configuring the ProCurve Access Controller xl Module (J8162A) Before beginning the configuration, backup current configurations of all devices. The Access Control Serer (740wl) and the Integrated Access Manager (760wl) software must be updated to version 4.1.3.x or later and the 5300xl switch software must be updated to version E.09.2x or later.

  • Page 54

    Getting Started With Switch Configuration Configuring the ProCurve Access Controller xl Module (J8162A) Next, configure the module with the IP address of the 740wl/760wl and its shared secret. access-control-server ip <ip address> secret <shared secret> <shared secret> The shared secret and IP address here are what you configured on the 740wl/ 760wl above.

  • Page 55: Xl Switch Configuration

    Getting Started With Switch Configuration Configuring the ProCurve Access Controller xl Module (J8162A) 5300xl Switch Configuration Configuring the switch consists of assigning switch ports as client downlink ports and reviewing the uplink VLAN used by the module. The client downlink ports connect the module to clients, for example, access points.

  • Page 56

    Getting Started With Switch Configuration Configuring the ProCurve Access Controller xl Module (J8162A) To confirm the uplink VLAN change, enter the following from the global configuration level ProCurve Switch 5308xl (config) # access-controller <slot ID> Show vlans You must assign at least one switch port to the uplink VLAN. This port must be an untagged member of the VLAN and the VLAN must be able to reach the 740wl/760wl.

  • Page 57: Configuring An Ip Address For The Module

    Getting Started With Switch Configuration Configuring the ProCurve Wireless Edge Services xl Modules (J9001A, J9003A) Configuring the ProCurve Wireless Edge Services xl Modules (J9001A, J9003A) Before beginning the configuration, backup the current configuration of the switch. The 5300xl switch software must be updated to version E.10.30 or later.

  • Page 58

    Getting Started With Switch Configuration Configuring the ProCurve Wireless Edge Services xl Modules (J9001A, J9003A) The following example enters the wireless services context of a module installed in Slot B of a 5300xl switch and then displays the IP address assigned by DHCP to the module: ProCurve# configure ProCurve(config)# wireless-services b...

  • Page 59: Configuring Vlans On The 5300xl Switch, Determining A Module Configuration Backup Process

    Getting Started With Switch Configuration Configuring the ProCurve Wireless Edge Services xl Modules (J9001A, J9003A) Configuring VLANs on the 5300xl Switch In a wireless services-enabled 5300xl switch, the Wireless Edge Services xl Module and the Redundant Wireless Services xl Module use ports on the switch to pass wired and wireless traffic to and from the network.

  • Page 60

    Getting Started With Switch Configuration Configuring the ProCurve Wireless Edge Services xl Modules (J9001A, J9003A) To run the Web browser interface for the ProCurve Wireless Edge Services xl Module, your workstation must be running Java Virtual Machine (JVM). If your workstation is not running the JVM and you attempt to open the module’s Web browser interface, the workstation will automatically try to access the Internet and download the JVM.

  • Page 61: Basic Troubleshooting Tips

    Troubleshooting This chapter describes how to troubleshoot your Switch 5300xl Series. Note that this document describes troubleshooting mostly from a hardware perspective. You can perform more in-depth troubleshooting using the soft- ware tools available with the switch, including the full-featured console interface, the built-in web browser interface, and ProCurve Manager, the SNMP-based network management tool.

  • Page 62

    Troubleshooting Basic Troubleshooting Tips ■ Improper Network Topologies. It is important to make sure you have a valid network topology. Common topology faults include excessive cable length and excessive repeater delays between end nodes. If you have network problems after recent changes to the network, change back to the previous topology.

  • Page 63

    Troubleshooting Basic Troubleshooting Tips If necessary though, you can modify the configuration of the ports on the Switch 5300xl Series to match the configuration of the connected device. Use the switch console, the web browser interface, or ProCurve Manager to modify the port configuration. ■...

  • Page 64: Diagnosing With The Leds

    Troubleshooting Diagnosing with the LEDs Diagnosing with the LEDs Tables 4-1 shows LED patterns on the switch and the switch modules that indicate problem conditions. Check in the table for the LED pattern you see on your switch Refer to the corresponding diagnostic tip on the next few pages. Table 4-1.

  • Page 65

    Troubleshooting Diagnosing with the LEDs Diagnostic Tips: Number Problem Solution ➊ The power supplies 1. Verify the power cord is plugged into an active power source and to the switch. installed in the Ensure these connections are snug. switch are not 2.

  • Page 66

    As Hewlett-Packard introduces new modules for your ProCurve Switch xl, you may have to update the switch with new operating code that supports the new module. The documentation that came with the module will indicate which version of the operating code is needed to support the module.

  • Page 67

    Troubleshooting Diagnosing with the LEDs Number Problem Solution ➐ The network port During the module self test, described in tip number 4 earlier in this table, each for which the Link network port is also tested. If the port self test fails, the individual port is not usable, LED is flashing has but the rest of the ports on the module, which have passed their self test, will experienced a self...

  • Page 68

    Troubleshooting Diagnosing with the LEDs Number Problem Solution The network Try the following procedures: connection is not • For the indicated port, verify both ends of the cabling, at the switch and the working properly. connected device, are securely connected. •...

  • Page 69: Proactive Networking

    Troubleshooting Proactive Networking Proactive Networking The Switch 5300xl Series have built-in management capabilities that proactively help you manage your network including: finding and helping you fix the most common network error conditions ■ (for example, faulty network cabling, and non-standard network topologies) ■...

  • Page 70: Hardware Diagnostic Tests, Testing The Switch By Resetting It, Checking The Switch Leds

    Troubleshooting Hardware Diagnostic Tests Hardware Diagnostic Tests Testing the Switch by Resetting It If you believe that the switch is not operating correctly, you can reset the switch to test its circuitry and operating code. To reset a switch, either: ■...

  • Page 71: Testing Twisted-pair Cabling, Testing Switch-to-device Network Communications, Testing End-to-end Network Communications

    Troubleshooting Hardware Diagnostic Tests Testing Twisted-Pair Cabling If you think the cable should work but still isn’t working, it may not be compatible with the IEEE 802.3 Type 10Base-T, 100Base-TX, or 1000Base-T standards, as appropriate for the switch port type that the cable is connected to.

  • Page 72: Restoring The Factory Default Configuration

    Troubleshooting Restoring the Factory Default Configuration Restoring the Factory Default Configuration As part of your troubleshooting process, it may become necessary to return the switch configuration to the factory default settings. This process momen- tarily interrupts the switch operation, clears any passwords, clears the console event log, resets the network counters to zero, performs a complete self test, and reboots the switch into its factory default configuration including deleting an IP address, if one is configured.

  • Page 73: Downloading New Code, Hp Customer Support Services, Before Calling Support

    HP Customer Support Services If you are still having trouble with your switch, Hewlett-Packard offers support 24 hours a day, seven days a week through the use of a number of automated electronic services. See the Customer Support/Warranty booklet that came with your switch for information on how to use these services to get technical www.procurve.com...

  • Page 75: Physical, Electrical, Environmental

    Specifications Physical Width: 44.2 cm (17.2 in) Depth: 39.0 cm (15.2 in) Height: • Switch 5308xl, 5372xl, 5308xl-48G • 22.5 cm (8.7 in) • Switch 5304xl, 5348xl, 5304xl-32G • 13.5 cm (5.2 in) Weight: • Switch 5308xl • 12.16 kg (26.80 lbs) •...

  • Page 76: Acoustic, Switch 5308xl And Switch 5372xl:, Switch 5304xl And Switch 5348xl:, Network Connectors, Safety

    Specifications Acoustic Switch 5308xl and Switch 5372xl: Geräuschemission LwA=63.1 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19 Noise Emission LwA=63.1 dB in a virtual workspace according to DIN 45635 T.19 Switch 5304xl and Switch 5348xl: Geräuschemission LwA=64.2 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19 Noise Emission LwA=64.2 dB in a virtual workspace according to DIN 45635 T.19...

  • Page 77: Switch Ports, Twisted Pair, Fiber-optic

    Switch Ports and Network Cables This appendix includes switch connector information and network cable information for cables that should be used with the Switch 5300xl Series, including minimum pin-out information and specifications for twisted-pair cables. N o t e Incorrectly wired cabling is the most common cause of problems for LAN communications.

  • Page 78: Cables

    Switch Ports and Network Cables Cables Twisted-Pair 10 Mbps Operation Category 3, 4, or 5 100-ohm differential unshielded twisted- pair (UTP) or shielded twisted-pair (STP) cable, complying with IEEE 802.3 Type 10Base-T specifications, fitted with RJ-45 connectors. 100 Mbps Operation Category 5 100-ohm differential UTP or STP cable, complying with IEEE 802.3u 100Base-TX specifications, fitted with RJ-45 connectors.

  • Page 79: Fiber-optic Cables

    Switch Ports and Network Cables Fiber-Optic Cables Port Type Cable Specifications Connector Type Maximum Length 62.5/125 mm or 50/125 μm (core/cladding) • 62.5 μm cable: Gigabit-SX LC - Gigabit-SX diameter, graded-index 850 nm, low metal mini-GBIC – 160 MHz*km=220 meters content, multimode fiber-optic cables, SC - Gigabit-SX –...

  • Page 80: Copper Cables, Twisted-pair Cable/connector Pin-outs

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Port Type Cable Specifications Connector Type Maximum Length 9/125 μm (core/cladding) diameter, 1310 nm, 10-GbE LR single-mode cable: 2-10 kilometers low metal content, single mode fiber-optic cables, complying with the ITU-T G.652 and ISO/IEC 793-2 Type B1 standards.

  • Page 81

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs N o t e HP Auto-MDIX was developed and shared with the IEEE for the development of the IEEE 802.3ab standard. HP Auto-MDIX and the IEEE 802.3ab Auto MDI/ MDI-X feature are completely compatible. If you connect a Series 5300xl Switch twisted-pair port to another switch or hub, which typically have MDI-X ports, the Series 5300xl Switch port automat- ically operates as an MDI port.

  • Page 82: Straight-through Twisted-pair Cable For 10 Mbps Or 100 Mbps Network Connections, Cable Diagram, Pin Assignments

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Straight-Through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections Because of the HP Auto-MDIX operation of the 10/100 ports on the switches, for all network connections, to PCs, servers or other end nodes, or to hubs or other switches, you can use straight-through cables.

  • Page 83: Mbps Or 100 Mbps Network Connection, Cable Diagram, Pin Assignments

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection The HP Auto-MDIX operation of the 10/100 ports on the switches also allows you to use crossover cables for all network connections, to PCs, servers or other end nodes, or to hubs or other switches.

  • Page 84: Mbps Network Connections, Cable Diagram, Pin Assignments

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Straight-Through Twisted-Pair Cable for 1000 Mbps Network Connections 1000Base-T connections require that all four pairs or wires be connected. Cable Diagram N o t e Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 1 and 2 on connector “B”.

  • Page 85: Safety Information

    Safety and EMC Regulatory Statements Safety Information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death.

  • Page 86: Informations Concernant La Sécurité

    Safety and EMC Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d'entraîner des dommages corporels ou la mort.

  • Page 87: Hinweise Zur Sicherheit

    Safety and EMC Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten.

  • Page 88: Considerazioni Sulla Sicurezza

    Safety and EMC Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza Simbolo di riferimento alla documentazione. Se il prodotto è contras- segnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNING denota un pericolo che può causare lesioni o morte.

  • Page 89: Consideraciones Sobre Seguridad

    Safety and EMC Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte.

  • Page 90: Safety Information (japan)

    Safety and EMC Regulatory Statements Safety Information (Japan) Safety Information (Japan) J a p a n P o w e r C o r d W a r n i n g...

  • Page 91: Safety Information (china)

    Safety and EMC Regulatory Statements Safety Information (China) Safety Information (China)

  • Page 92: Emc Regulatory Statements, U.s.a, Canada, Australia/new Zealand, Japan

    Safety and EMC Regulatory Statements EMC Regulatory Statements EMC Regulatory Statements U.S.A. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment.

  • Page 93: Korea, Taiwan, Regulatory Model Identification Number

    Switch 5300xl Series are assigned a Regulatory Model Number. The Regulatory Model Number for these switches is RSVLC-0202. This regulatory number should not be confused with the marketing name (ProCurve Switch 5300xl Series), or product numbers (J4819A, J4848A, J4849B, J4850A)

  • Page 94: European Community

    This product was tested with HP branded products only. Roseville, 22 January 2008 European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ- TRE, Herrenberger Straße 140, D-71034 Böblingen (FAX: + 49-7031-14-3143) C-10...

  • Page 95: Waste Electrical And Electronic Equipment (weee) Statements

    Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.

  • Page 96

    Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja varmistamaan, että...

  • Page 97

    Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnan- dole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche.

  • Page 98

    Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem.

  • Page 99

    Index Symbols Bootp automatic switch configuration … 3-2 ! (attention) LED … 1-7 for in-band console access … 2-19 buttons Numerics Clear button … 1-8 LED Mode Select button … 1-7 100/1000Base-T Reset button … 1-8 connections, length limitations … 2-6 note on cable requirements …...

  • Page 100

    cables, twisted pair console port category 3, 4, 5 … B-5 description … 1-8 connector pin-outs … B-4 location on switch … 1-4 crossover cable pin-out … B-7 crossover cable HP Auto-MDIX feature … B-4 pin-out … B-7 MDI-X to MDI connections … B-6, B-8 use with fixed port configurations …...

  • Page 101

    Fault LED behavior during self test … 2-13 in-band description … 1-5 console access, types of … 2-19 flashing definition … 1-6 managing the switch … 3-1 location on switch … 1-4 included parts … 2-1 showing error conditions … 4-4 installation FDx LED …...

  • Page 102

    showing error conditions … 4-4 on switch chassis … 1-5 network cables on switch modules … 1-6 100/1000Base-T Power … 1-5 connections … 2-6 behavior during error conditions … 4-4 1000Base-LH connections … 2-6 behavior during self test … 2-13 1000Base-LX connections …...

  • Page 103

    Power LED behavior during error conditions … 4-4 safety and regulatory statements … C-1 behavior during self test … 2-13 safety specifications … A-2 description … 1-5 selecting the Mode LED display … 1-7 location on switch … 1-4 self test Power Status LEDs …...

  • Page 104

    switch modules troubleshooting … 4-1 booting the switch to initialize changed module basic tips … 4-1 type … 2-8 checking port configuration … 4-3 hot swapping … 2-21 checking the console messages … 4-10 installing … 2-8 checking the LEDs … 4-10 LEDs descriptions …...

  • Page 108

    © Copyright 2001, 2005 - 2007 Hewlett-Packard Development Company, L.P. Printed in Singapore December 2007 Manual Part Number 5991-8597 *5991-8597*...

Comments to this Manuals

Symbols: 0
Latest comments: