HP J4850A Installation And Getting Started Manual: Configuring The Procurve Access Controller Xl Module (j8162a); 740wl/760wl Configuration; Module Configuration
Procurve series 5300xl switches.
Hide thumbs
1
2
3
4
Table of Contents
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
Advertisement
Configuring the ProCurve Access
Controller xl Module (J8162A)
Before beginning the configuration, backup current configurations of all
devices. The Access Control Serer (740wl) and the Integrated Access Manager
(760wl) software must be updated to version 4.1.3.x or later and the 5300xl
switch software must be updated to version E.09.2x or later.
There are three phases of configuration:
configuration of the 740wl/760wl
■
■
configuration of the module
configuration of the 5300xl switch
■
740wl/760wl Configuration
HP recommends the use of a static IP address for the 740wl/760wl. If the IP
address of the 740wl/760wl should change, access controller xl modules and
720wl Access Controllers would need to be reconfigured. Record this infor-
mation, you will need it to configure the module. You also need to configure
a shared secret on the 740wl/760wl. Refer to the documentation that came
with that unit.
Module Configuration
Once the module has been installed into the 5300xl switch you need to
configure it to enable communication with the 740wl/760wl. The module
requires an IP address. By default the module uses DHCP to obtain an IP
address. ProCurve recommends using DHCP to configure the module's IP
address. If you need to configure a specific IP address for the module, do the
following:
From the CLI command prompt at the global configuration level
ProCurve Switch 5308xl (config) #
enter access-controller<slot ID>
where <slot ID> is the slot letter (A-H) where the module is installed.
To configure the module's IP address
enter ip address <IP> <mask>
where <IP> is the selected address and <mask> is the selected mask. CIDR
notation "/mask bit number" (for example 10.1.1.1/24) is an acceptable
shortcut for the IP address mask combination.
Getting Started With Switch Configuration
Configuring the ProCurve Access Controller xl Module (J8162A)
3-7
Advertisement
Related Manuals for HP J4850A
-
Switch HP 5300 Reviewer's Manual
Procurve 5300xl series (35 pages)
-
Switch HP ProCurve 5304xl Specifications
Hp procurve 5304xl: specifications (4 pages)
-
Switch HP J4865A Installation And Getting Started Manual
Procurve series 4100gl switches (94 pages)
-
Switch HP J4897A Brochure & Specs
Procurve switch 2700 series unmanaged 24- and 8-port switches with 10/100/1000 auto-sensing per port (4 pages)
-
Switch HP J4818A Installation And Getting Started Manual
Procurve 2300 & 2500 series (88 pages)
-
Switch HP J4868A Brochure & Specs
24-port switch with 10/100 auto-sensing per port and 1 open transceiver slot for a 100base-fx uplink (5 pages)
-
Switch HP ProCurve J4820B Supplementary Manual
Hp procurve j4820b: supplementary guide (2 pages)
-
Switch HP ProCurve J4852A Install Manual
Hp procurve j4852a: install guide (36 pages)
-
Switch HP ProCurve J4862A Install Manual
Hp procurve j4862a: install guide (36 pages)
-
Switch HP ProCurve J4863A Brochure
Hp procurve j4863a: product brochure (17 pages)
-
Switch HP J4900B Installation And Getting Started Manual
Procurve series 2600 switches (116 pages)
-
Switch HP J4902A Installation And Getting Started Manual
Multiport switch (86 pages)
-
Switch HP J4111A Installation Manual
Procurve switch module (32 pages)
-
Switch HP J4091A Installation And Reference Manual
Procurve series 100base-t hub 8 (56 pages)
-
Switch HP 1920 Gigabit Ethernet Switch Series User Manual
Hp 1920 gigabit ethernet switch series (547 pages)
Related Content for HP J4850A
- ProCurve J8162A Configuring The Access Controller Xl Module
- procurve switch xl modules Controller Xl Module (j8162a)
- ProCurve J8162A Access Controller Xl Module Overview
- ProCurve J8162A Using 5300xl Features With The Access Controller Xl Module
- procurve switch xl modules Hp Procurve Switch Poe Xl Module Configurations
- ProCurve J8162A Displaying Access Controller Xl Status From The 5300xl Cli
- ProCurve 2520 Hp Procurve Switch Xl Poe Module For The 5300xl Switch
- ProCurve J8162A Access Controller Context Command Syntax
- MSM3xx Access-controller Restrict Location
- MSM7XX Access Controller Context
- HP ProCurve series 2500 Configuring For Snmp Access To The Switch
- ProCurve Series 8212zl Configuring An Ip Address For The Module
- 4108GL Configuring For Snmp Access To The Switch
- 316095-B21 - StorageWorks Edge Switch 2/24 Configuring Remote Management Access
Comments to this Manuals
Latest comments: