Extron electronics SW USB Pro Series User Manual page 30

Command
Resets
Reset to factory defaults
Reset all IP settings
NOTE: This command includes the 2BOOT
followed by Reconfig
Reset all settings except IP
settings
Absolute system reset
NOTE: Entering this command or performing a mode 5 reset via the rear panel Reset button (see
starting on page 14) changes the current passwords (whether user‑set or the factory‑set serial number) to extron.
IP Configuration
Set DHCP mode 24
View DHCP mode
Set IP address 24
View IP Address
Set subnet mask
14,24
View subnet mask
Set gateway IP address 14,24
View gateway IP address
Set IP, subnet, and gateway
addresses
View IP, subnet, and gateway
addresses
View hardware (MAC)
address
X%
KEY:
= DHCP status
X*
= Media access code (MAC)
X(
= IP address
X1)
= Subnet mask
X1!
= Gateway IP address
ASCII Command
(Host to Unit)
E }
ZXXX
E }
1ZQQQ
}
command so a separate 2BOOT
] ]
and Boot2
responses.
E }
ZY
E }
ZQQQ
EX% DH }
E }
DH
EX( }
CI
E }
CI
EX1) }
CS
E }
CS
EX1! G }
C
E }
CG
E X( X1) X1!
24
1* / * CISG
E 1CISG }
E }
CH
Response
(Unit to Host)
]
Zpx
]
Zpq1
}
]
Zpy
]
Zpq
Idh X%]
X%]
In verbose modes 2 and 3:
X%]
Idh
Ipi X(]
•
X(]
In verbose modes 2 and 3:
Ipi X(]
•
X1)]
Ips•
X1)]
In verbose modes 2 and 3:
X1)]
Ips•
X1!]
Ipg•
X1!]
In verbose modes 2 and 3:
X1!]
Ipg•
}
Cisg X( / X1) X1!]
*
•1*
X( / X1)
X1!]
*
In verbose modes 2 and 3:
Cisg X( / X1) X1!]
*
•1*
X*]
In verbose modes 2 and 3:
X*]
Iph•
0 = DHCP disable (default), 1 = DHCP enable
xx-xx-xx
00-05-A6-
Format nnn.nnn.nnn.nnn (Default is 192.168.254.254)
Format nnn.nnn.nnn.nnn (Default is 255.255.255.0)
Format nnn.nnn.nnn.nnn (Default is 0.0.0.0)
SW USB Pro Series • Remote Configuration and Control
Additional Description
Reset the switcher to factory default
values.
Reset only IP settings to factory values.
command is not required. The Zpq1
Reset all device settings to
factory defaults except IP settings
(communication is preserved). This
command is recommended for after a
firmware update.
Reset all device settings to factory
defaults except the firmware version.
Reset Mode Summary Table
Set Dynamic Host Configuration
Protocol (DHCP) to
disable automatic assigning of IP
addresses.
View DHCP status
Set IP address
View IP address
Set subnet mask
View subnet mask
Set gateway address
nnn.nnn.nnn.nnn
(
View gateway address
View IP address
X1)
mask prefix
X1!
address at one time.
View media access code (MAC)
hardware address
]
response is
X%
to enable or
X%
.
X(
.
X(
for the unit.
X1)
for the unit.
X1)
for the unit.
X1!
for the unit
).
X1!
for the unit.
X(
, subnet
, and gateway
X*
for the unit.
22