Omron VARISPEED G7 Instruction Manual page 410

No. Name
Motor 2 mid. output frequency 1
E3-05
(FB)
Motor 2 mid. output frequency
E3-06
voltage 1 (VC)
Motor 2 min. output frequency
E3-07
(FMIN)
Motor 2 min. output frequency
E3-08
voltage (VMIN)
E4-01 Motor 2 rated current
E4-02 Motor 2 rated slip
E4-03 Motor 2 no-load current
Motor 2 number of poles (number
E4-04
of poles)
E4-05 Motor 2 line-to-line resistance
E4-06 Motor 2 leak inductance
E4-07 Motor 2 rated capacity
F1-01 PG constant
Operation selection at PG open cir-
F1-02
cuit (PGO)
Operation selection at overspeed
F1-03
(OS)
F1-04 Operation selection at deviation
F1-05 PG rotation
PG division rate (PG pulse moni-
F1-06
tor)
Integral value during accel/decel
F1-07
enable/disable
F1-08 Overspeed detection level
F1-09 Overspeed detection delay time
Excessive speed deviation detec-
F1-10
tion level
Excessive speed deviation detec-
F1-11
tion delay time
F1-12 Number of PG gear teeth 1
F1-13 Number of PG gear teeth 2
F1-14 PG open-circuit detection time
Bi-polar or uni-polar input selec-
F2-01
tion
F3-01 Digital input option
F4-01 Channel 1 monitor selection
F4-02 Channel 1 gain
F4-03 Channel 2 monitor selection
F4-04 Channel 2 gain
F4-05 Channel 1 output monitor bias
F4-06 Channel 2 output monitor bias
Analog output signal level for
F4-07
channel 1
Table 10.5 User Constants (Continued)
Fac-
Set-
tory No.
ting
Setting
*2
F4-08
3.0
*7
F5-01
11.0
*2
F5-02
0.5
*7
F5-03
2.0
*6
F5-04
1.90
*6
F5-05
2.90
*6
F5-06
1.20
4 F5-07
*6
F5-08
9.842
*6
F5-09
18.2
*6
F6-01
0.40
600 F6-02
1 F6-03
1 F6-04
3 F6-06
0 H1-01 Terminal S3 function selection
1 H1-02 Terminal S4 function selection
0 H1-03 Terminal S5 function selection
115 H1-04 Terminal S6 function selection
0.0 H1-05 Terminal S7 function selection
10 H1-06 Terminal S8 function selection
0.5 H1-07 Terminal S9 function selection
0 H1-08 Terminal S10 function selection
0 H1-09 Terminal S11 function selection
2.0 H1-10 Terminal S12 function selection
0 H2-01
0 H2-02
2 H2-03
1.00 H2-04
3 H2-05
0.50 H3-01
0.0 H3-02 Gain (terminal A1)
0.0 H3-03 Bias (terminal A1)
0 H3-04
Name
Analog output signal level for
channel 2
Channel 1 output selection
Channel 2 output selection
Channel 3 output selection
Channel 4 output selection
Channel 5 output selection
Channel 6 output selection
Channel 7 output selection
Channel 8 output selection
DO-08 output mode selection
Operation selection after commu-
nications error
Input level of external fault from
Communications Option Card
Stopping method for external fault
from Communications Option
Card
Trace sampling from Communica-
tions Option Card
Torque reference/torque limit
selection from optical option
Terminal M1-M2 function selec-
tion (contact)
Terminal M3-M4 function selec-
tion (open collector)
Terminal M5-M6 function selec-
tion (open collector)
Terminal P3 function selection
(open-collector)
Terminal P4 function selection
(open-collector)
Signal level selection (terminal
A1)
Signal level selection (terminal
A3)
User Constants
Fac-
Set-
tory
ting
Setting
0
0
1
2
4
6
37
0F
0F
0
1
0
1
0
1
24
14
*8
3 (0)
*8
4 (3)
*8
6 (4)
8 (6)
5
32
7
15
0
1
2
6
5
0
0
100.0
0
21
10-