Miscellaneous Symbols And Definitions - Miller Millermatic 355 Owner's Manual

Keep your head out of the fumes
Do not weld on drums or any closed containers.
?
Wear dry insulating gloves. Do not touch electrode (wire) with bare hand. Do not wear wet or damaged gloves.
Read Owner's Manual and inside labels for connection points and procedures.
3-2.

Miscellaneous Symbols And Definitions

Induction heating can cause injury or burns from hot items such as rings, watches, or parts.
Amperage
3
Voltage
Rated No-Load
Voltage
Keep flammables away from welding. Do not weld near flammables.
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Do not cut on drums or any closed containers.
Become trained and read the instructions before working on the
Welding sparks can cause fires. Have a fire extinguisher nearby, and
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
machine or welding.
Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
have a watchperson ready to use it.
Do not grip material near cutting path.
Become trained and read the instructions before working on the
machine or cutting.
Do not weld on drums or any closed containers. Do not weld on drums or any closed containers.
Turn off power before disassembling torch.
Falling unit can cause injury and damage. Do not move unit where two wheels are at a different height and unit
could tip avoid tipping. Be careful when moving unit over uneven surfaces.
Remove unit from shipping crate. Remove Owner's Manual from unit.
Follow instructions to install muffler.
Writer: If necessary, replace the word "handle" with "lift eye'.
Do not cut on drums or any closed containers. Writer: If necessary, replace the word "handle" with "lift eye'.
Do not stack racks. Lift only with proper equipment and correct procedures.
Do not remove or paint over (cover) the label. Do not remove or paint over (cover) the label.
Do not use one handle to lift or support unit.
Do not use one handle to lift or support unit.
Every 100 hours, check and clean filter and check condition of hoses.
Moving parts can injure.
Do not grip material near cutting path.
Drive rolls can injure fingers.
Drive rolls can injure fingers.
Drive rolls can injure fingers.
During the first 50 hours of operation keep welding load above 200
amperes. Do not weld below 200 amperes of output.
Always connect green, Or green with yellow stripe, wire to supply grounding terminal.
Turn off power before disassembling torch.
Welding wire and drive parts are at welding voltage during operation -
Welding wire and drive parts are at welding voltage during operation
Welding wire and drive parts are at welding voltage during operation
Connect black, white, and red wires (L1, L2, L3) to line terminals.
keep hands and metal objects away.
After the first 50 hours of operation, change the engine oil and filter.
Pinch points can injure.
Become trained and read the instructions before working on the
Pinch points can injure.
Do not remove or paint over (cover) the label.
machine or welding.
Consult rating label for input power requirements.
Consult rating label for input power requirements.
Wear hat and safety glasses. Use ear protection and button shirt col-
Wear hat and safety glasses. Use ear protection and button shirt
Recycle.
lar. Use welding helmet with correct shade of filter. Wear complete
collar. Use welding helmet with correct shade of filter. Wear complete
body protection made from leather or flame-resistant clothing (FRC).
body protection.
Body protection includes oil-free clothing such as leather gloves,
heavy shirt, cuffless trousers, high shoes, and a cap.
Become trained and read the instructions and labels before working on machine.
Become trained and read the instructions and labels before working on machine.
Become trained and read the instructions before working on machine.
Become trained and read the instructions before working on the
Become trained and read the instructions before working on the ma-
machine or welding.
chine or welding.
Connect Green Or Green/Yellow grounding conductor to ground terminal first.
Connect Green Or Green/Yellow grounding conductor to ground terminal first.
Connect input conductors (L1, L2, L3) to line terminals.
Connect input conductors (L1, L2, L3) to line terminals.
Connect green or green/yellow grounding conductor to ground terminal.
Move jumper links as shown on inside label to match input voltage at
job site. Include extra length in grounding conductor and connect
grounding conductor first. Connect line input conductors as shown on
Direct Current
inside label. Double-check all connections, jumper link positions, and
input voltage before applying power.
Alternating Current
Close door before turning on unit.
Rated Supply
Voltage
Read the Owner's Manual before working on this machine.
at job site. Double-check all connections, relinking board position, a
input voltage before applying power.
For single phase operation, insulate and isolate red conductor.
Include extra length in grounding conductor and connect grounding
conductor first. Connect black, white, and red wires (L1, L2, L3) to
line terminals.
Wear hat and safety glasses. Use ear protection and button shirt
Wear hat and safety glasses. Use ear protection and button shirt
(DC)
collar. Use welding helmet with correct shade of filter. Wear comple
collar. Use welding helmet with correct shade of filter. Wear comple
body protection.
body protection.
Connect input conductors (L1, L2 And L3) to line terminals.
Wear hat and safety glasses. Use ear protection and button shirt
Wear hat and safety glasses. Use ear protection and button shirt
collar. Use welding helmet with correct shade of filter. Wear comple
collar. Use welding helmet with correct shade of filter. Wear comple
body protection.
body protection.
Become trained and read the instructions before working on the
Become trained and read the instructions before working on the
machine or welding.
machine or welding.
Safe7 2017 04
Safe40 2012 05
Safe41 2012 05
Safe46 2012 05
Safe51 2012 05
keep hands and metal objects away.
keep hands and metal objects away.
Safe54 2017 04
Safe64 2017 04
Safe55 2012 05
Safe65 2012 06
Safe57 2017 04
Safe66 2012 06
Safe65 2012 06
Safe67 2012 06
Conventional Load
Safe74 2012 07
Voltage
Safe68 2012 06
Rated Welding
Current
OM-
Input Power Or
Input Voltage
Safe69 2012 06
OM-288360 Page 11
Safe70 2012 06
Safe62 201
Safe14 2012
Safe96 2012
Safe17 201
Safe63 201
Safe15 2012
Safe18 201
Safe97 2012
Safe16 201
Safe19 201
Safe98 201
Safe17 201
Safe20 201
Safe99 201
Safe31 201
Safe31 2017
Safe18 201
Safe100 201
Safe32 201
Safe32 201
Safe19 201
Safe101 2012
Safe33 201
Safe33 201
Safe102 2012
Safe20 201
Safe34 2012
Safe34 2012
Safe103 2012
Safe35 201
Safe35 201
Safe104 2012
Safe36 201
Safe36 201
Safe105 2012
Safe38 201
Safe38 201
Safe 106 2012
Safe39 201
Safe39 201
Safe40 2012
Safe40 2012