Miscellaneous Symbols And Definitions - Miller Auto-Line XMT 350 MPa Owner's Manual

A complete Parts List is available at www.MillerWelds.com
SECTION 3
3-2.

Miscellaneous Symbols And Definitions

13-2. Mode Switch Settings
Welding (GMAW)
Switch Position
Scratch Start TIG
Scratch Start TIG
Welding (GMAW)
Pulsed MIG
V-Sense Feeder
*See Configuration Option Menu (see S
13-3. Configuration Option Menu
3
OM-231242 Page 12
�
Complete Parts List is available at www.MillerWelds.com
DEFINITIONS
= < 60
= < 60
Three Phase
A complete Parts List is available at www.MillerWelds.com
Negative
Gas Metal Arc
Foot Control Gun
Single Phase
Positive
Lift-Arc TIG
Gas Metal Arc
Gas Tungsten Arc
TIG
Welding
Pulse
MIG
Press
CC
On
Stick
Three Phase
Remote
Percent
Use coolant suggested by the manufacturer.
Use coolant suggested by the manufacturer.
Falling unit can cause injury. Do not move or operate unit where it could tip.
Falling unit can cause injury. Do not move or operate unit where it could tip.
after power is turned off before working on unit, AND check input ca-
pacitor voltage, and be sure it is near 0 before touching any parts.
Hazardous voltage remains on input capacitors after power is turned
off. Do not touch fully charged capacitors. Always wait
Hazardous voltage remains on input capacitors after power is turned Hazardous voltage remains on input capacitors after power is turned
after power is turned off before working on unit, AND check input ca-
off. Do not touch fully charged capacitors. Always wait 5 minutes after off. Do not touch fully charged capacitors. Always wait
pacitor voltage, and be sure it is near 0 before touching any parts.
power is turned off before working on unit, AND check input capacitor
power is turned off before working on unit, AND check input capacitor
voltage, and be sure it is near 0 before touching any parts. voltage, and be sure it is near 0 before touching any parts.
Hazardous voltage remains on input capacitors after power is turned
Always lift and support unit using both handles. Keep angle of lifting
off. Do not touch fully charged capacitors. Always wait
device less than 60 degrees.
Always lift and support unit using both handles. Keep angle of lifting
power is turned off before working on unit, AND check input capacitor
device less than 60 degrees. Use a proper cart to move unit. Use a proper cart to move unit.
voltage, and be sure it is near 0 before touching any parts.
Always lift and support unit using both handles. Keep angle of lifting
%
device less than 60 degrees.
Percent
Engine fuel plus flames or sparks can cause fire.
Use a proper cart to move unit.
Increase
Increase
Engine fuel plus flames or sparks can cause fire.
Output
Remove unit from shipping crate. Remove Owner's Manual from unit.
Off
Follow instructions to install muffler.
Shielded Metal
Arc Welding
Single Phase
(SMAW)
Remove unit from shipping crate. Remove Owner's Manual from unit.
Follow instructions to install muffler.
Read Owner's Manual. Read labels on unit.
Lift-Arc Operation
(GTAW)
Read Instructions
Pulsed
Gas Tungsten Arc
Move jumper links as shown on inside label to match input voltage at
Read Owner's Manual. Read labels on unit. Welding (GTAW)
job site. Include extra length in grounding conductor and connect
Torch
grounding conductor first. Connect line input conductors as shown on
inside label. Double-check all connections, jumper link positions, and
input voltage before applying power.
Foot Control
Move jumper links as shown on inside label to match input voltage at
job site. Include extra length in grounding conductor and connect
grounding conductor first. Connect line input conductors as shown on
inside label. Double-check all connections, jumper link positions, and
Plugged filter or hoses can cause overheating to the power source
Volts
input voltage before applying power.
and torch.
Gas Output
Plugged filter or hoses can cause overheating to the power source
and torch.
Every 100 hours, check and clean filter and check condition of hoses.
Every 100 hours, check and clean filter and check condition of hoses.
Safe42 2017 04
60 seconds
5 minutes after
Safe42 2017 04
Safe43 2017 04
5 minutes after
Safe43 2017 04
Safe44 2012 05
Safe44 2012 05
Positive
Safe45 2012 05
Shielded Metal Arc
(SMAW) Electrode
Holder
Safe45 2012 05
Safe46 2012 05
Touch Start (GTAW)
Safe46 2012 05 Input
Safe47 2012 05
Amperes
Safe47 2012 05
Safe49 2012 05
Output
Negative
Safe49 2012 05
Safe50 2012 05
Gas Input
Safe50 2012 05
Safe51 2012 05
4
5
Safe51 2012 05
Safe52 2012 05
Safe52 2012 05
Safe53 2017 04
OM-
Safe53 2017 04
6
OM-
7