CommScope NOVUX SEC 100 Installation Instructions Manual
Fiber optic system
Hide thumbs
Also See for NOVUX SEC 100:
- Installation instructions manual (7 pages) ,
- Installation instructions manual (8 pages)
Table of Contents
Advertisement
Quick Links
TC-1557-IP
Rev. A, December 2022
http://www.commscope.com
About this manual
This manual describes the basic installation steps of the SEC 100 system with an inline feeder cable. The document
starts with providing an overview of the tools required to perform the installation. Also warnings and cautions are
indicated, which should be observed before starting the product installation.
Installation steps in this document are limited to: closure preparation, mounting the closure, organizer preparation,
inline feeder cable preparation and installation, storing feeder fibers and closing the closure. For the installation steps
required for the splice application, refer to TC-1557-IP-SP: SEC 100 Splice application. For the installation steps required
for the patch application, refer to TC-1557-IP-PA: SEC 100 Patch application. Images in this manual are for reference
only and are subject to change.
System overview
Clip
Dimensions closure
Cable range
Feeder Cable
Drop cable push through
Drop cable connectorized
Branch cable
NOVUX™ Fiber Optic System
SEC 100 Basic Instructions
Cable range (mm)
8-12
3-7
3-6
8-12
page 1 / 14
© 2022 CommScope, Inc. All Rights Reserved
Installation Instructions
S E C Closure
1
2, 3, 4
2, 3, 4, 5 or 1, 2, 3, 4
5
Position in closure
Advertisement
Table of Contents
Related Manuals for CommScope NOVUX SEC 100
Summary of Contents for CommScope NOVUX SEC 100
- Page 1 Cable range (mm) Position in closure Feeder Cable 8-12 Drop cable push through 2, 3, 4 Drop cable connectorized 2, 3, 4, 5 or 1, 2, 3, 4 Branch cable 8-12 page 1 / 14 © 2022 CommScope, Inc. All Rights Reserved...
- Page 2 Dimensions clip page 2 / 14 © 2022 CommScope, Inc. All Rights Reserved...
-
Page 3: Table Of Contents
Inline feeder cable preparation............7 Close the closure................13 6.1 Use cable holder....................7 Disclaimer..................14 6.2 Window cut mounted in the closure............7 Contact information..............14 6.3 Window cut to cut the fiber................ 8 page 3 / 14 © 2022 CommScope, Inc. All Rights Reserved... -
Page 4: Tools
Cable ties black small Cable ties white Silicone tape (1,25 cm width) Mounting equipment Patch panel (SC or LC) - patch application only Note: Contents can vary depending on the configuration. page 4 / 14 © 2022 CommScope, Inc. All Rights Reserved... -
Page 5: Accessories
The cover can be locked to keep it open. Open the cover 130° and slide the cover to the left or the right. The hinge will be locked in the bottom. In the cover a fiber guidance pen is stored to help to handle the fibers. page 5 / 14 © 2022 CommScope, Inc. All Rights Reserved... -
Page 6: Remove The Cover
Tray fully removed. The bottom is now accessible to install the inline feeder cable. Note: The components mounted in the bottom are application dependent. The images are showing a router island in the bottom. page 6 / 14 © 2022 CommScope, Inc. All Rights Reserved... -
Page 7: Inline Feeder Cable Preparation
Light signal Use cable holder The cable holder can be used with a CommScope cable of 9,2 mm. Slide the cable holder between the cable and the mounting surface where the window cut should be created. Secure the cable under the two locking tabs. -
Page 8: Window Cut To Cut The Fiber
Remove the seals from the closure. Cut an opening from the bottom side in one of the feeder ports. For a cable larger then 10 mm cut away the inner rubber. page 8 / 14 © 2022 CommScope, Inc. All Rights Reserved... - Page 9 12 Secure the bottom of the closure to the mounting surface with the 2 screws and install a washer between the bottom and the head of the screw. page 9 / 14 © 2022 CommScope, Inc. All Rights Reserved...
-
Page 10: Pull Back The Fiber
Protect window cut to cut fiber CLICK To protect the window cut created to cut the selected fiber, a clip can be used. Slide the clip between the cable and page 10 / 14 © 2022 CommScope, Inc. All Rights Reserved... -
Page 11: Route Feeder Fibers To The Tray
The hinges of the tray will lock now into the squared cavities of the bottom. Route the fiber to the tray Remove the cover of the tray. Bring the feeder fiber to the tray. page 11 / 14 © 2022 CommScope, Inc. All Rights Reserved... -
Page 12: Reinstall The Cover
Tray closed with the feeder fiber routed to the tray. Reinstall the cover CLICK Reinstall the tray cover. Mount the cover on the bottom by sliding the hinges into the cavities. A clicking sound is observed. page 12 / 14 © 2022 CommScope, Inc. All Rights Reserved... -
Page 13: Close The Closure
Slide the cover a maximum to the front then rotate the cover downwards To lock the closure, push the locking feature to the rear side. A clicking sound is observed. page 13 / 14 © 2022 CommScope, Inc. All Rights Reserved... -
Page 14: Disclaimer
This product may be covered by one or more U.S. patents or their foreign equivalents. For patents, see www.cs-pat.com. This document is not intended to modify or supplement any specifications or warranties relating to CommScope products or services.
Need help?
Do you have a question about the NOVUX SEC 100 and is the answer not in the manual?
Questions and answers