CommScope OFDC-B8G Installation Instructions Manual

CommScope OFDC-B8G Installation Instructions Manual

Outdoor fiber distribution closur.

Advertisement

Quick Links

TC-1426-IP
Ver 00, Issue 03, May 2019
www.commscope.com
Contents
1
General product information ������������������������������������������������ 1
2
Product image������������������������������������������������������������������������� 1
3
Warnings and caution ������������������������������������������������������������ 2
4
Kit content ������������������������������������������������������������������������������� 2
5
Closure preparation ���������������������������������������������������������������� 2
6
Feeder cable installation �������������������������������������������������������� 3
6.1
Feeder cable preparation ......................................................................... 3
6.2
Feeder cable installation ........................................................................... 3
6.3
Feeder cable fiber routing ........................................................................ 3
7
Install branch cable ���������������������������������������������������������������� 4
8
Install organizer in housing ��������������������������������������������������� 4
1

General product information

The OFDC-B8G is the environmentally sealed enclosure for fiber management system that provides the function of splicing
(66 splices and for repair up to 90) / patching and passive component integration in the external network.
The closure is sealed with gel for longitudinal seal and wrap around gel block for cable sealing (IP68) 2m water head.
The organizer is fully removable from the closure body and the addition of customers is transient free.
Cable diameters:
2

Product image

660003357
Rev. A
OUTDOOR FIBER DISTRIBUTION CLOSURE
2 main cables:
2 branch cables:
8/16 drop cables:
OFDC-B8G
9
9.1
Installing 1 cable per drop port ............................................................... 5
9.2
Installing 2 cables per drop port ............................................................ 6
10
Install Connectorized drop cable ������������������������������������������ 7
11
Install TAP's/Splitters ������������������������������������������������������������� 7
12
Extra features �������������������������������������������������������������������������� 7
13
Mounting options������������������������������������������������������������������� 8
14
Overview of possibilities �������������������������������������������������������� 8
15
Trade-marks ��������������������������������������������������������������������������� 8
16
Contact information ��������������������������������������������������������������� 8
11.5-15 mm
8-11 mm
0-5.5 mm
Installation Instructions
��������������������������������� 5
© 2019 CommScope, Inc. All Rights Reserved
Page 1 of 8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OFDC-B8G and is the answer not in the manual?

Questions and answers

Summary of Contents for CommScope OFDC-B8G

  • Page 1: Table Of Contents

    Install organizer in housing ��������������������������������������������������� 4 General product information The OFDC-B8G is the environmentally sealed enclosure for fiber management system that provides the function of splicing (66 splices and for repair up to 90) / patching and passive component integration in the external network.
  • Page 2: Warnings And Caution

    Install the 2 screws (1-2 turns) and the wedge (If needed). Slide the gel block on to the organizer. Verify the correct orientation: Head of the screw facing upwards. Page 2 of 8 © 2019 CommScope, Inc. All Rights Reserved...
  • Page 3: Feeder Cable Installation

    Take out the fiber tubes to be used and store the remaining loops as shown. (Secure with cable ties) 6.3.2 Install blind plugs in the unused port(s) and close the gel block with the top gel part. Page 3 of 8 © 2019 CommScope, Inc. All Rights Reserved...
  • Page 4: Install Branch Cable

    45°. 6.3.5 Store the fibers on the tray. Changing direction is possible with figure 8, see picture above. Tighten the 2 top screws. 6.3.6 Secure the trays as shown. Page 4 of 8 © 2019 CommScope, Inc. All Rights Reserved...
  • Page 5: Install Drop Cables (Spliced)

    Installing 1 cable per drop port (0-5�5 mm) 9.1.4 Secure the cable to the T-shape with a cable tie. 9.1.1 Remove the cable jacket over a length of 1 m. Page 5 of 8 © 2019 CommScope, Inc. All Rights Reserved...
  • Page 6: Installing 2 Cables Per Drop Port

    2 cm gel strip is mandatory. Gel strip to be ordered separately: S1515-30X1.5X700-AUTO-N 9.2.4 Secure the drop cable with Cable ties as shown. 9.2.1 Cut 2 cm of the gel strip. Page 6 of 8 © 2019 CommScope, Inc. All Rights Reserved...
  • Page 7: Install Connectorized Drop Cable

    Install TAP’s/Splitters Feeder fiber to splice tray 12.2 Top cover can be locked in open position. 11.1 Install the TAP-module/splitter as shown. For the drop connection see section 10. Page 7 of 8 © 2019 CommScope, Inc. All Rights Reserved...
  • Page 8: Mounting Options

    Strand mount: OFDC-C12 BRKSTRAND (To be ordered not intended to modify or supplement any specifications separately). or warranties relating to CommScope products or services. CommScope is committed to the highest standards of business integrity and environmental sustainability, with a number of CommScope’s facilities across the globe certified in accordance with international standards, including ISO 9001, TL 9000, and ISO 14001.

Table of Contents