TVLogic LVM-180A Operation Manual
  1. Manuals
  2. Brands
  3. TVLogic Manuals
  4. Monitor
  5. LVM-180A
  6. Operation manual

TVLogic LVM-180A Operation Manual

Mult format lcd monitor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
LVM-180A
MULT FORMAT
LCD Monitor
# Operation manual_V1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LVM-180A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for TVLogic LVM-180A

Summary of Contents for TVLogic LVM-180A

  • Page 1 LVM-180A MULT FORMAT LCD Monitor # Operation manual_V1.1...
  • Page 2 FCC (Federal Communications Commission) This equipment has been tested and found to comply with the limits for class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
  • Page 3 Contents CAUTION MAIN FEATURES CONTROLS & FUNCTIONS MENU ORGANIZATION & ADJUSTMENT MENU OPERATIONS [1] PICTURE [2] COLOR [3] MARKER [4] GPI / UMD [5] WAVEFORM [6] AUDIO [7] DISPLAY & SET FIRMWARE UPGRADE BUTTON FUNCTIONS OTHER FUNCTIONS VIDEO SUPPORT RESOLUTION PRODUCT SPECIFICATIONS...
  • Page 4 01 CAUTION Multi Format LCD Monitor • Always use set voltage. • If any of the following conditions occur, unplug - AC 100 ~ 240V (50~60Hz) or DC 12V the power cord from the AC outlet, and request a qualified service person to perform repairs. •...
  • Page 5 01 CAUTION Multi Format LCD Monitor • Unplug the power cord from the AC outlet • The vents and other openings in the cabinet are before cleaning the product. Use a damp cloth designed for ventilation. Do not cover or block to clean the product.

  • Page 6: Main Features

    Multi Format LCD Monitor 02 MAIN FEATURES LVM-180A contains the following features : • Compatible with varied SDI signals • Varied Markers & Safety Areas - The product is compatible with varied - Center Marker, Safety Area Marker, Aspect SD/HD/3G(A/B)-SDI Marker, Display Size(Scan) 480i,576i,720p,1080i/p,1080psf.

  • Page 7: Controls And Functions

    Multi Format LCD Monitor 03 CONTROLS & FUNCTIONS LVM-180A ALL PART (FRONT / REAR) SDI-B MENU/EXIT SDI-A ENTER/UP/DOWN DIGITAL POWER ANALOG PHONE JACK INPUT SIGNAL INDICATOR SPEAKER INFO BLUE ONLY H/V DELAY MARKER ASPECT SCAN HDMI CVBS IN-OUT DVI-I(HDCP) SDI-A IN...
  • Page 8 Multi Format LCD Monitor 03 CONTROLS & FUNCTIONS LVM-180A FRONT • [INPUT SIGNAL INDICATOR] Lamp • [H/V DELAY] Button/Lamp - Used to display the current input mode. - Used to check horizontal sync and vertical sync CVBS: Composite, DVI-A: DVI Analog simultaneously.
  • Page 9 • [POWER S/W] • [RS422 IN/OUT] (RJ-45) - Power On/Off switch - Controls the monitor by a protocol provided by TVLogic or supports TSL protocol. • [DC IN] - 12V DC • [DVI-I] (DVI-I) - Signal input terminal for DVI ANALOG or DVI DIGITAL signal.

  • Page 10: Menu Organization & Adjustment

    Multi Format LCD Monitor 04 MENU ORGANIZATION & ADJUSTMENT MENU ORGANIZATION & MENU ADJUSTMENT & MENU ADJUSTMENT PROCEDURE [1] Menu Organization [3] Menu Adjustment Procedure • The product may be controlled and set • Menu control sequence follows the order below. system-wise through OSD displayed on the screen.
  • Page 11 Multi Format LCD Monitor 04 MENU ORGANIZATION & ADJUSTMENT MENU ORGANIZATION & MENU ADJUSTMENT & MENU ADJUSTMENT PROCEDURE [4] Menu Tree Brightness PIN 1 Contrast PIN 2 Chroma PIN 3 Phase PIN 4 Aperture PIN 5 NTST Setup PIN 6 Key Lock PIN 7 Output Mode Select...
  • Page 12 Multi Format LCD Monitor 04 MENU ORGANIZATION & ADJUSTMENT MENU ORGANIZATION & MENU ADJUSTMENT & MENU ADJUSTMENT PROCEDURE [4] Menu Tree Waveform type System Default Waveform Intensity Eco Saving Waveform Trans. User Config Set Waveform Size OSD Position Line Waveform Key LED Select Line Position Firmware Version...

  • Page 13: Menu Operations

    [Full] (255) and [Limited] (235). Multi Format LCD Monitor • Contrast LVM-180A - This item controls contrast ratio between [-100] and [100]. #Contrast ratio can be adjusted by using a control knob on the front of the monitor.
  • Page 14 Multi Format LCD Monitor 05 MENU OPERATIONS [1] PICTURE (DVI ANALOG) • Image Position • Brightness - This items moves the picture position for - This item controls the degree of brightness Up/Down/Left/Right. between [-100] and [100]. #Brightness can be adjusted by using a control knob on the front of the monitor.
  • Page 15 Multi Format LCD Monitor 05 MENU OPERATIONS [2] COLOR • Color Copy - This menu is used to copy the pre-stored color temperature settings into a USER1/2/3 mode. - In USER mode, find and select the color temperature to be used as a starting point of custom color temperature.
  • Page 16 Multi Format LCD Monitor 05 MENU OPERATIONS [3] MARKER • Fit Marker - This menu activates the FIT MARKER function. - With FIT MARKER On, the Safety Area is displayed relative to the marker in use. With FIT MARKER Off, the Safety Area is displayed relative to the incoming source.
  • Page 17 Multi Format LCD Monitor 05 MENU OPERATIONS [3] MARKER *USER MARKER H1/H2/V1/V2 activate when the [Marker] menu is set to [User] mode. • USER Marker H1 - This menu controls the position of the first user defined horizontal marker line. - Adjustment range is [1] to [1920].
  • Page 18 Multi Format LCD Monitor 05 MENU OPERATIONS [4] GPI / UMD PIN No. Settable Values NONE ANALOG CHANNEL DIGITAL CHANNEL SDI-A/B CHANNEL TALLY R TALLY G BLUE ONLY UNDER SCAN • This product provides a REMOTE CONTROL ASPECT mode. H/V DELAY The user may connect RJ-45 jack to the 16:9 MARKER REMOTE terminal on the rear of the unit and...
  • Page 19 • UMD character color - This menu sets the ID of each monitor for the - This menu sets the color of the UMD letter. TVLogic control protocol or DYNAMIC UMD - Available mode is [Green], [Blue], [Yellow], using RS-422/485 communication.
  • Page 20 - This menu sets the tally operation when D-UMD(TVL_D8C) is set in UMD DISPLAY. - The selectable values are [Default] and [User Color]. Default: Original TVLogic managing method (VRT) User color: The user can set each tally color. - When User color is selected, Tally1 Color ~ Tally4 Color items are activated.
  • Page 21 Multi Format LCD Monitor 05 MENU OPERATIONS [4] GPI / UMD <Dynamic UMD Protocol (TSL V3.1)> * Transmission (18 Byte) (PC or Device -> Monitor) HEADER CONTROL DISPLAY DATA (1 BYTE) BYTE(1 BYTE) (16 BYTE) * [HEADER] : Display address (0~126) + 80 hex. * [CONTROL BYTE] bit 0 : Tally 1 (1=on, 0=off) bit 1 : Tally 2 (1=on, 0=off)
  • Page 22 Multi Format LCD Monitor 05 MENU OPERATIONS [4] GPI / UMD • Tally Type - Default - TVL_S8C(Single 8 Characters) & TVL_S16C(Single 16 Characters) Bit 1 Bit 1 Operation (Tally2) (Tally1) CHANNEL1 CHANNEL1 CHANNEL1 CHANNEL1 - TVL_D8C(Dual 8 Characters) Bit 1 Bit 1 Operation (Tally4)
  • Page 23 Multi Format LCD Monitor Waveform Wide: Displays the stretched LVM-180A luminance components of the input signal to fit width of the screen on the bottom of the monitor. Waveform YCbCr: Displays the Cb, Cr components of the input signal into waveform.
  • Page 24 Multi Format LCD Monitor 05 MENU OPERATIONS [5] WAVEFORM • Luma(Y’) Zone Check - Analyzes Luma (Y’) of input signal and displays the analyzed area on the screen. - Available modes are [Color Patt. On] and [Zebra Patt. On]. - After each pixel’s Y’ level is analyzed, it is displayed as a certain color or zebra pattern according to the Index on the right side of the screen.
  • Page 25 Multi Format LCD Monitor 05 MENU OPERATIONS [5] WAVEFORM • C Max - Sets the maximum value of Chroma (C’) level between [0] and [255]. - Pixels whose value exceed the maximum C’ level blink in the screen and are displayed in red on the Waveform.
  • Page 26 Multi Format LCD Monitor 05 MENU OPERATIONS [6] AUDIO *8CH: 4 channels are displayed on the top-left of the screen and the other 4 channels on the top-right horizontally. *8CH Side: 8 channels are displayed on the top-right horizontally. *4CH: 2 channels are displayed on the top-left of the screen and the other 2 channels on the top-right horizontally.
  • Page 27 Multi Format LCD Monitor 05 MENU OPERATIONS [7] DISPLAY & SET • Key LED - This function turns on and off the LED in front of the monitor. - Even though you turn off Key LED, when you press LED button in front of the monitor, the LED is on and after 5 seconds the LED is off.
  • Page 28 - Available range is [0] to [100]. - The feature is only available when [Focus Assist] mode is selected. [Focus Assist] mode can be selected by pressing [BLUE ONLY] button as well as by adjusting in OSD menu. Multi Format LCD Monitor LVM-180A...
  • Page 29 Multi Format LCD Monitor 05 MENU OPERATIONS [7] DISPLAY & SET • S/W upgrade - This menu is used to update the firmware using the USB memory stick(Thumb drive). - For more detailed information, refer to “6. Firmware Upgrade” in the page 29. •...

  • Page 30: Firmware Upgrade

    * During the update, the monitor screen is off, and nothing functions. * After the update, TVLogic logo shows up on the screen, and the monitor initializes. * Update can take 10 to 20min. depending on firmware kind.

  • Page 31: Button Functions

    Multi Format LCD Monitor 07 BUTTON FUNCTIONS [1] ANALOG [2] DIGITAL INPUT • LVM-180A monitor supports HDMI/DVI digital • LVM-180A monitor supports various analog input signal. input signals. 1. Press [DIGITAL] in front of the monitor and the 1. Press [ANALOG] in front of the monitor and OSD menu appears as the picture below.

  • Page 32: Sdi Input

    [3] SDI INPUT [4] FUNCTION KEY SET • The Function Keys allow the user to activate • LVM-180A monitor supports the two HD/SD/ the desired functions quickly. 3G-SDI inputs. 1. Hold [F1] to [F5] key in front of the monitor for 1.

  • Page 33: Other Functions

    Multi Format LCD Monitor 08 OTHER FUNCTIONS [1] SCAN • The function can select the various scan mode. • Press [SCAN] in front of the monitor and the Scan mode changes. 1. Press [SCAN] button, and the Scan mode changes in order of [Zero Scan], [Over Scan], [User Aspect].
  • Page 34 Multi Format LCD Monitor 08 OTHER FUNCTIONS [2] USER ASPECT • Select [Aspect] mode in the OSD menu to activate the [User Aspect] mode. • After activation, press the Knob to get ready for controlling. - Adjust the ratio using the Knob. - To adjust the 16:9 aspect ratio of 1920x1080 - Control range for width: Min[100] ~ Max[1920] resolution into 2.35:1 aspect ratio, adjust the...

  • Page 35: Waveform / Vectorscope

    Multi Format LCD Monitor 08 OTHER FUNCTIONS [3] WAVEFORM / VECTORSCOPE • Waveform / Vector • VectorScope - This function sets the Waveform and Vectorscope. - Displays the color components ‘B-Y’ and ‘R-Y’ of - Activates in order of Off, Waveform, VectorScope, the input signals onto the X-Y axis.
  • Page 36 Multi Format LCD Monitor 08 OTHER FUNCTIONS [4] SELECT LINE POSITION [5] ZOOM (Waveform / VectorScope) / • Used to select a specific horizontal line for • Used to magnify the input signal from 0% to 90%. WAVEFORM and VECTOR SCOPE. •...
  • Page 37 Multi Format LCD Monitor 08 OTHER FUNCTIONS [6] LUMA(Y") ZONE CHECK • COLOR PATTERN TYPE • LUMA(Y’) ZONE CHECK function is convenient to set the exposure or the lighting so that the skin tone or the specific color tone is correctly shot. - Displays the pixels with the designated Luma(Y’) levels of the input image in colors.

  • Page 38: Focus Assist

    Multi Format LCD Monitor 08 OTHER FUNCTIONS [7] FOCUS ASSIST [8] RANGE ERROR • Focus Assist function assigns a color to the • Pixels with Y’ or C’ levels exceeding the pixels in the shape or the boundary of the designated levels adjusted in Y MAX, Y MIN, image to inform the user to achive the best C MAX and C MIN menu shall blink.
  • Page 39 Multi Format LCD Monitor 08 OTHER FUNCTIONS [9] INTERNAL PATTERN [10] INPO. • Displays the internally generated test patterns • Displays the current status and function setting - The internal test pattern consists of of the monitor. • It displays when you press [INFO.] button in ColorBar+Pluge and Gray.

  • Page 40: Video Support Resolution

    Multi Format LCD Monitor 09 VIDEO SUPPORT RESOLUTION [1] SDI MODE Input Signal Signal Format (SD SDI) Interface 720x487(59.94i) SD-SDI YCbCr 4:2:2 10bit 720x576(50i) Input Signal Signal Format (SD SDI) Interface 1920x1080(23.98/24/25/29.97/30p) HD-SDI (50/59.94/60i) (24/25/29.97/30psf) YCbCr 4:2:2 10bit 1280x720(50/59.94/60P) Input Signal Signal Format (SD SDI) Interface 1920x1080(60p/59.94p/50p) Y...
  • Page 41 Multi Format LCD Monitor 09 VIDEO SUPPORT RESOLUTION [3] DVI-DIGITAL/HDMI GRAPHIC MODE Resolution Frequency [4] DVI-DIGITAL/HDMI VIDEO MODE Resolution Frequency There are GRAPHIC mode and VIDEO mode in DVI DIGITAL mode. If the SCAN mode is not set to ZERO SCAN in DVI-ANALOG, DVI-DIGITAL GRAPHIC, DVI-GRAPHIC VIDEO, HDMI mode, the image may not be properly displayed.

  • Page 42: Product Specifications

    Multi Format LCD Monitor 10 PRODUCT SPECIFICATIONS LVM-180A Size 18.5" Resolution 1920 x 1080 (16:9) Pixel Pitch 213(per one triad) x 213 [um] Support Color 16.7M colors (True 8 Bit) Luminance of white 500cd/m2 (Typical) Contrast Ratio 1000:1 (Typical) Active Area 408.96(H) x 230.04 (V) [mm]...

Table of Contents