Gastroback DESIGN MULTI JUICER DIGITAL Operating Instructions Manual page 38

Problem Reason The Solution
The display is illu- The processing sys- Ensure to install the juicing system completely and correctly
minated, showing a tem is not installed (see: 'Mounting the Juicing System'').
speed selection, but correctly. For your
the motor does not safety, the safety
respond. interlocks prevent
operation.
The overheat protec- Turn the selection dial to "OFF", switch off at the power switch,
tion device has been and unplug the appliance (see: 'Self-Resetting Overheat Protec-
triggered. tion Device'). Leave the appliance cool down for at least 1/2
hour. Do not let the appliance operate continuously for a too
long time (see: 'Method of Operation and Making Breaks').
The motor has been Turn the selection dial to "OFF", switch off at the power switch,
stalled for more and unplug the appliance. Remove the obstacle. Thereafter, you
than 10 seconds. may start operation again.
The overload protec-
tion has been trig-
gered.
The automatic shut- After letting the appliance operate for more then 20 minutes,
off has been trig- the automatic shut-off is activated. Simply turn the selection
gered. dial to another speed selection to re-activate the appliance (see:
'Automatic Shut-Off').
From the start on, This may appear Depending on the load that is straining the motor, regularly
the motor seems to during operation. make breaks every 7-20 minutes to avoid overheating (see:
run with an uneven 'Method of Operation and Making Breaks').
speed.
The appliance is With a large amount of hard, glutinous, or fibrous food and/
operated on heavy or large, hard pieces of food, the motor is strained with hea-
load. vy load. After max. 7 minutes of continuous operation, make
a break of 20 minutes to avoid overheating (see: 'Method of
Operation and Making Breaks').
74
Problem Reason The Solution
The motor base gets The power cord is Always unwind the power cord completely before operation to
unexpectedly hot still wound partly avoid overheating (see: 'Before First Use').
during operation. around the cord
storage during ope-
ration.
The motor is already Do not let the appliance operate continuously for more than 20
running continuously minutes. With heavy load, make a break after each 7 minutes
for a too long time. (see: 'Method of Operation and Making Breaks'). If required,
process your food in portions.
Malfunction has Immediately unplug the appliance. Get in contact with an autho-
occurred. rised service centre for examination and repair.
The motor stops Too much too hard Immediately switch off (selection dial to "OFF", power switch
unexpectedly during or fibrous food in to "O") and unplug (see: 'Electronic Overload Protection').
operation. the juicing system is Remove the obstacle (see: 'Emptying the Containers and Remo-
blocking the knives. ving Obstacles'). Thereafter, try again.
The overheat protec- Immediately switch off (selection dial to "OFF", power switch
tion device has been to "O") and unplug. Leave the appliance cool down for at least
triggered. 30 minutes (see: 'Self-Resetting Overheat Protection Device').
Thereafter, try again.
The electronic over- Immediately switch off (selection dial to "OFF", power switch
load protection has to "O") and unplug (see: 'Electronic Overload Protection').
been triggered. Remove the obstacle (see: 'Emptying the Containers and Remo-
ving Obstacles'). Thereafter, try again.
After leaving the Simply turn the selection dial to another speed selection to re-
appliance operate activate the appliance (see: 'Automatic Shut-Off'). However,
for more then 20 you should make a break of at least 20 minutes: switch "OFF"
minutes, the auto- the appliance completely (at the selection dial and power
matic shut-off has switch). Then unplug the appliance and wait for the appliance
been triggered. to cool down.
75