Related Manuals for DFI ED700-EHL22I
Summary of Contents for DFI ED700-EHL22I
- Page 1 Quick Installation Guide ED700-EHL22I Fanless Embedded System www.dfi.com Package Contents • 1 ED700/ED710-EHL System Unit • Wall Mount Bracket • Power Cord (Optional) © September 22, 2023 DFI Inc.
-
Page 2: Product Overview
Product Overview Front View USB 3.0 Antenna Holes LAN (2.5G) Isolated COM1 & COM2 (support 2KV) Isolated 6bit DI & 6bit DO (support 2KV) COM 1 & 2 DC-In (9~36V) Grounding Quick Installation Guide | ED700-EHL22I... - Page 3 Side I/O view SIM Slot USB 2.0 Antenna Holes Quick Installation Guide | ED700-EHL22I...
-
Page 4: Removing The Chassis Cover
The 5 screws on the bottom of the system are used to secure the cover to the chassis. Remove the screws and put them in a safe place for later use. Step 2: Lift the cover to open the system. The board can be easily accessed after the chassis cover is removed. Quick Installation Guide | ED700-EHL22I... -
Page 5: Installing An M.2 Card
3. Locate the M.2 socket on the system board 4. Make sure the notch on card is aligned to the key on the socket. 5. Make sure the standoff screw is removed from the standoff. M.2 Module M.2 Socket Stand-off Notch Quick Installation Guide | ED700-EHL22I... - Page 6 Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. Quick Installation Guide | ED700-EHL22I...
-
Page 7: Installing The So-Dimm Module
3. Locate the SO-DIMM socket on the system board 4. Make sure the notch on memory card is aligned to the key on the socket. Retention Notch Notch DDR4 SO-DIMM Retention Clip Socket Top View 4 5 ° Step 1 Quick Installation Guide | ED700-EHL22I... - Page 8 Inspect that the clip sits in the notch. If not, please pull the clips outward, release and remove the card, and mount it again. Step 3 Quick Installation Guide | ED700-EHL22I...
-
Page 9: Installing An Antenna
There are antenna holes reserved on the front and left side of the system and covered by six knockout tabs. Please remove the knockout tabs prior to installing an antenna. Knockout tabs for antenna holes Knockout tabs for antenna holes Quick Installation Guide | ED700-EHL22I... - Page 10 Connect the internal cable to the board's antenna connector, screw the antenna connector through the antenna hole with washers and nuts, and screw on the antenna as illustrated below. Antenna Chassis Wall Module Connector Cable Antenna Connector Washer Quick Installation Guide | ED700-EHL22I...
-
Page 11: Mounting Options
• Din-rail mount bracket • 2 screws Step 1: Use the provided mounting screws to attach the din-rail mount bracket to the rear side of the system. Step 2: Install the sytem onto the rail. Quick Installation Guide | ED700-EHL22I... -
Page 12: Pin Assignment
PIN Assignment X Isolation COM1 & COM2 COM 1 COM 2 DCD2# DCD1# SIN2 SIN1 DTR2# DTR1# DSR2# DSR1# RTS2# RTS1# CTS2# CTS1# RI2# RI1# Quick Installation Guide | ED700-EHL22I... - Page 13 X Isolation DIO1 & DIO2 DIO 1 DIO 2 GPO1 GPI1 GPO2 GPI2 GPO3 GPI3 GPO4 GPI4 GPO5 GPI5 GPO6 GPI6 X DC-in Assignment Quick Installation Guide | ED700-EHL22I...
- Page 14 (RS422/Full) (RS485) DATA- DATA+ DFI reserves the right to change the specifications at any time prior to the product's release. This QR may be based on the product’s revision. For more documentation and drivers, please visit the download page at www.dfi.com/...