Page 2
1. The changes or modifications not expressly approved by the party responsible for com- are the properties of the respective owners. pliance could void the user’s authority to operate the equipment. 2. Shielded interface cables must be used in order to comply with the emission limits. User's Manual | ED700-EHL22I...
Network Stack Configuration..................25 USB Power Control ......................26 Chipset ..........................27 Graphics Configuration ....................27 PCH-IO Configuration ....................28 PCH-IO Configuration ► PCI Express Configuration ...........28 PCH-IO Configuration ► SATA Configuration .............29 ► Audio Configuration ............29 PCH-IO Configuration Security ..........................30 User's Manual | ED700-EHL22I...
Page 4
The manual is subject to change and update without notice, and may be based on editions that do not resemble your actual products. Please visit our website or contact our sales representa- • 1 ED700-EHL22I System Unit tives for the latest editions. •...
Page 5
Make sure the system is placed or mounted correctly and stably to prevent the chance of dropping or falling may cause damage. • The openings on the system shall not be blocked and shall be kept in distance from User's Manual | ED700-EHL22I...
Support 1 x 2.5GbE TSN , 3 x GbE LAN Wide Operating Temperature: Operating temperature: 0 to 60°C -40 to 60°C (Supported by Intel Embedded Series ) ® Isolated COM & DIO Support isolated COM & DIO 4 x LAN User's Manual | ED700-EHL22I...
Ethernet Controller I210/I211 GigE LAN ® 1 x Intel Ethernet 2.5GigE LAN ® Indicators 1 x Power LED 1 x HDD LED 1 x WiFi LED 1 x 4G/5G LED 2 x COM LED 8 x DIO LED User's Manual | ED700-EHL22I...
Page 9
Dimensions (W x H x D) 72 x 172 x 118.2 (mm) Weight 1.6 kg STANDARDS AND Shock Operating: 3G, 11ms CERTIFICATIONS Non-Operating: 5G, 11ms Vibration Operating: Random 5~500Hz, IEC68-2-64 (3G) Non-Operating: Sine 10~500Hz, IEC68-2-6 (3G) Certifciation CE, FCC, RoHS User's Manual | ED700-EHL22I...
The 5 screws on the bottom of the system are used to secure the cover to the chassis. Remove The board can be easily accessed after the chassis cover is removed. the screws and put them in a safe place for later use. User's Manual | ED700-EHL22I...
Connect the internal cable to the board's antenna connector, screw the antenna connector through the antenna hole with washers and nuts, and screw on the antenna as illustrated below. Antenna Chassis Wall Module Connector Cable Antenna Connector Washer Knockout tabs for antenna holes User's Manual | ED700-EHL22I...
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. User's Manual | ED700-EHL22I...
Inspect that the clip sits in the notch. If not, please pull the clips outward, release and remove the card, and mount it again. 4 5 ° Step 3 Step 1 User's Manual | ED700-EHL22I...
The DIN Rail mount kit includes the following: • Din-rail mount bracket • 2 screws Step 1: Use the provided mounting screws to attach the din-rail mount bracket to the rear side of the system. Step 2: Install the sytem onto the rail. User's Manual | ED700-EHL22I...
When “X” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press <Enter>. User's Manual | ED700-EHL22I...
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays min- utes from 00 to 59. Second displays seconds from 00 to 59. User's Manual | ED700-EHL22I...
The system automatically powers on after power failure. S5 State The system enter soft-off state after power failure. Power-on signal input is required to power up the system. Last State The system returns to the last state right before power failure. User's Manual | ED700-EHL22I...
Enable or disable turbo mode of the processor. This field will only be displayed when EIST is enabled. C states Enable or disable CPU Power Management. It allows CPU to enter "C states" when it’s idle and nothing is executing. User's Manual | ED700-EHL22I...
Set SuperIO WatchDog Timer Timeout value. The range is from 0 (disabled) to 255. To clear the existing TPM encryption, select "TPM Clear" and restart the system. This field is not available when "Security Device Support" is disabled. Note: The sub-menus are detailed in following sections. User's Manual | ED700-EHL22I...
NCT6126D Super IO Configuration ► Serial Port 1,2 Configuration ► Serial Port 3,4 Configuration Serial Port Serial Port Enable or disable serial port. Enable or disable serial port. Electrical Interface Mode Choose mode between RS232 / RS485 / RS422 User's Manual | ED700-EHL22I...
SYS Fan = [ SMART FAN IV ], [ Manual mode ] Fan control mode select Temperature 1 to 4 The value of temperature. FD/RPM 1 to 4 The value of Fan Duty/RPM when temperature is T1. User's Manual | ED700-EHL22I...
Select data bits: 7 bits or 8 bits. Parity Select parity bits: None, Even, Odd, Mark or Space. Stop Bits Select stop bits: 1 bit or 2 bits. Flow Control Select flow control type: None or RTS/CTS. User's Manual | ED700-EHL22I...
Set the wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value. Media detect count Set the number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. User's Manual | ED700-EHL22I...
Chapter 4 BIOS SETTINGS Advanced USB Power Control USB Power 5V_Dual: Support system wake from S3/S4 by USB KB&MS 5V: No Support system wake from S3/S4 by USB KB&MS User's Manual | ED700-EHL22I...
X Chipset Chipset Graphics Configuration Primary Display Select which of IGFX/PEG/PCI Graphics device to be the primary display. Internal Graphics Keep IGFX "Enabled" or "Disabled" based on the setup options, or select "Auto" for auto-detec- tion. User's Manual | ED700-EHL22I...
Select one of the PCI Express channels and press enter to configure the following settings. M.2-E, M.2-M, M.2-B Control the PCI Express Root Port. PCI Express Configuration PCI Express Configuration Settings SATA Configuration SATA Device Otpions Settings Audio Configuration Audio Subsystem Configuration Settings User's Manual | ED700-EHL22I...
This option allows you to create RAID or Intel Rapid Storage configuration along with Intel® Optane™ system acceleration on Serial ATA devices. Ports and Hot Plug Enable or disable the Serial ATA port and its hot plug function. User's Manual | ED700-EHL22I...
Clear the database from the NVRAM, including all the keys and signatures installed in the Key Management menu. Press Enter and a prompt will show up for you to confirm. Key Management Enables expert users to modify Secure Boot Policy variables without full authentication. User's Manual | ED700-EHL22I...
Select this option to save BIOS configuration settings to a USB flash device. ► Restore Setting from file This field will appear only when a USB flash device is detected. Select this field to restore set- ting from the USB flash device. User's Manual | ED700-EHL22I...
MAC address should be burned or not. c. After updating unique MAC Address from manufacturing, NVM will be protected immediately after power cycle. Users cannot update NVM or MAC address. User's Manual | ED700-EHL22I...