JVC HR-S3500U Instructions Manual page 3

IMPORTANT PRODUCT
SAFETY I NSTRUCTIONS
Electrical energy can perform many useful functions. But
improper use can result in potential electrical shock or fire
hazards. This product has been engineered and manufactured
to assure your personal safety. In order not to defeat timebuilt-in
safeguards, observe the folk)wing basic rules for its installation,
use and servicing.
ATTENTION:
Follow and ()bey all warnings and instructions marked on your
product and its operating instructions. For your safety, please
read all timesafety and operating instructions before you operate
this product and keep this booklet for future reference.
INSTALLATION
1, Grounding or Polarization
(A) Your product may be equipped with a polarized alternating-
current line plug (a plug having one blade wider than time
other). This plug will fit into the power outlet only one way.
This is a safety feature.
If you are unable to insert time plug fully into the outlet, try
reversing the p]ug. If the p]ug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
(B) Your product may be equipped with a 3-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety
feature.
If you are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from timetype of power source
indicated on the marking [abe[. If you are not sure of the type of
power supply to your home, consult your product dealer or
local power company. If your product is intended to operate
from battery power, or other sources, refer to the operating
instructions.
3. Overloading
Do not overload wan outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
5. Ventilation
Slots and openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and to protect it
from overheating, these openings must not be blocked or
covered.
® Do not block the operlilmgs by placing the product on a bed,
sofa, rug or other similar surface.
® Do not place the product in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.
6. Wall or Ceiling Mounting
Timeproduct should be mounted to a wall or ceiling only as
recommended by the manufacturer.
ANTENNA INSTALLATION
INSTRUCTIONS
I. Outdoor Antenna Grounding
If aim outside antenna or cable system is connected to time
product, be sure time antenna or cable system is grounded so as
to provide some protection against voltage surges and built-up
static charges. Article 810 of time National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper
grounding of time mast and supporting structure, grounding of
the lead-in wire to aimantenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
2. Lightning
For added protection for this product during a lightning storm,
or when it is [eft unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna
or cable system. This will prevent damage to the product due to
lightning and power-line surges.
3. Power Lines
Aim outside antenna system should not be located in time vicinity
of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be
taken to keep from touching such power lines or circuits as
contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
_JANTENNA
-'_ LEAD INWIRE
........ // _-_
>.-ANTENNA
I ...... / J/i DISCHARGE UNIT
I I / _ I (NECSECTION
I /U_.J
-T_/_>"_G RO UNDING
I[_ CONDUCTORS
__'x_ (NECSECTION 810-21)
_ GROUND CLAMPS
POWER SERVICE G ROUNDING E LECTRODE SYSTEM
(NECART250. PART H)
NEC - NATIONAL ELECTRICAL CODE