Toshiba TOSVERT VF-P7 Instruction Manual page 221

[31] Meter output (2/2)
Communi
Title
cation No
0690

AM/FM output parameter for adjustment −
∼ ∼
 0697
[32] Control panel parameters
Communi
Title Function
cation No
 0700 Prohibition of parameter setting 0: Allowed，1: Prohibited
0701 Current/voltage display mode 0: [%], 1: [A] or [V]

 0702 Frequency free unit magnification 0.00: OFF, 0.01∼200.0
0703 Decimal place number of frequency 0: 1 [Hz], 1: 0.1 [Hz], 2: 0.01 [Hz]

 0704 Decimal place number of acc/dec time 0: 1[s], 1: 0.1[s], 2: 0.01[s]
Prohibition of user parameter
 0709
initialization at type form initialization
 0710 Monitor display mode setting 0∼29
0711 Status monitor #1 display mode 0∼29

 0712 Status monitor #2 display mode 0∼29
0713 Status monitor #3 display mode 0∼29

 0714 Status monitor #4 display mode 0∼29
0720 Selection of panel V/f1, 2, 3 or 4

 0721 Panel stop pattern
0722 Panel reset function

 0723 Panel torque limit
0724 Panel PID control OFF

0725 Panel torque reference

 0726 Panel synchronized torque bias -250∼250 [%]
0727 Panel tension torque bias

 0728 Panel load sharing gain
0729 Panel over-ride multiplication gain -100∼100 [%]

 0730 Panel operation prohibition
Function Adjustment range
Adjustment range
0: Allowed
1: Prohibited
1: V/f #1, 2: V/f #2, 3: V/f #3, 4: V/f #4
0: Deceleration stop，1: Coast stop
0: Disabled, 1: Enabled
1∼4
0: ON, 1: OFF
0∼250 [%]
-250∼250 [%]
0∼250 [%]
0: All key operations prohibited
+1: Panel frequency setting enabled
+2: Parameter reading/writing enabled
+4: Monitor display operation enabled
+8: Panel drive operation enabled
(+16: no function)
+32: Emergency stop operation enabled
63: Default mode (all key operation enabled)
Sensorless vector/vector with sensor (●valid, −:invalid)
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
− − − −
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
− 0 Enabled ●/●
0 Enabled
− ●/●
0.01/0.01 0.00 Enabled ●/●
1 Enabled
− ●/●
− 1 Enabled ●/●
− 0 Enabled
●／●
− 0 Enabled ●/●
1 Enabled
− ●/●
− 2 Enabled ●/●
3 Enabled
− ●/●
− 4 Enabled ●/●
1 Enabled
− −
− 0 Disabled ●/●
1 Disabled
− ●/●
− 1 Enabled ●/●
0 Enabled
− ●/●
1/0.01 0 Enabled
−
1/0.01 0 Enabled ●/●
1/0.01 0 Enabled
−
1/0.01 100 Enabled −
1/0.01 0 Enabled
●/●
− 63 Disabled ●/●
Vector control
V/f Reference
Torque Position
Constant section
control control
− − − −
Vector control
V/f Reference
Torque Position
Constant section
control control
●/● −/● ● 6.29.1
6.29.2
●/● −/● ●
●/● −/● ● 6.29.3
6.29.4
●/● −/● ●
●/● −/● ● 6.29.4
−
●／● ―／● ●
●/● −/● ● 8.1
8.1
●/● −/● ●
●/● −/● ● 8.1
8.1
●/● −/● ●
●/● −/● ● 8.1
6.29.6
− − ●
●/● −/● ● 6.29.7
6.29.8
●/● −/● ●
●/● −/● ● 6.29.9
6.29.10
− − ●
6.29.11
●/● − −
− −/● − 6.21.4
6.21.4
●/● − −
●/● − − 6.21.4
6.29.13
− − ●
●/● −/● ● 6.29.14