Toshiba TOSVERT VF-P7 Instruction Manual page 208

[7] Speed/torque reference gain/bias setup (1/2)
Communi
Title Function
cation No
 0200 Reference priority selection
0201 VI/II reference point #1

 0202 VI/II reference point #1 frequency 0.0∼ [Hz]
0203 VI/II reference point #2

 0204 VI/II reference point #2 frequency 0.0∼ [Hz]
0205 VI/II reference point #1 rate

 0206 VI/II reference point #2 rate
0207 Speed setting mode selection #2 Same as  (1 to 11)

 0208 / switching frequency 0.1∼ [Hz]
0209 Analog input filter

 0210 RR reference point #1
0211 RR reference point #1 frequency 0.0∼ [Hz]

 0212 RR reference point #2
0213 RR reference point #2 frequency 0.0∼ [Hz]

 0214 RR reference point #1 rate
0215 RR reference point #2 rate

 0216 RX reference point #1
0217 RX reference point #1 frequency -∼ [Hz] (*3)

 0218 RX reference point #2
0219 RX reference point #2 frequency -∼ [Hz] (*3)

 0220 RX reference point #1 rate
0221 RX reference point #2 rate

 0222 RX2 reference point #1
 0223 RX2 reference point #1 frequency -∼ [Hz] (*3)
 0224 RX2 reference point #2
 0225 RX2 reference point #2 frequency -∼ [Hz] (*3)
0226 RX2 reference point #1 rate

 0227 RX2 reference point #2 rate
(*1): When setup frequency(signal set up by ) is  or more, signal set up by  is accepted, When setup frequency is lower than , the inverter runs under the signal of .
(*2): When setup frequency(signal set up by ) is  or more, signal set up by  is accepted, When setup frequency is lower than , the inverter runs under the signal of .
(*3): Adjustment range is -327.68∼327.67 [Hz] in case of 16-bit access.
※(Reference section): Refer to the inverter's individual manual.
Adjustment range
0: 
1: 
2:  priority (*1)
3:  priority (*2)
4: / switching
0∼100 [%]
0∼100 [%]
-250∼250 [%] (For torque control, etc.)
-250∼250 [%] (For torque control, etc.)
0(Disabled) to 3(Max. filter capacity)
0∼100 [%]
0∼100 [%]
0∼250 [%] (For torque control, etc.)
0∼250 [%] (For torque control, etc.)
-100∼100 [%]
-100∼100 [%]
0∼250 [%] (For torque control, etc.)
0∼250 [%] (For torque control, etc.)
-100∼100 [%]
-100∼100 [%]
-250∼250 [%] (For torque control, etc.)
-250∼250 [%] (For torque control, etc.)
Sensorless vector/vector with sensor (●valid, −:invalid)
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
− 0 Enabled ●/●
1/0.01 20.0 Enabled
●/●
0.01/0.01 0. 0 Enabled ●/●
1/0.01 100 Enabled
●/●
0.01/0.01 80.0 Enabled ●/●
1/0.01 0 Enabled
●/●
1/0.01 100 Enabled ●/●
1 Enabled
− ●/●
0.01/0.01 1.0 Enabled ●/●
0 Enabled
− ●/●
1/0.01 0 Enabled ●/●
0.01/0.01 0.0 Enabled
●/●
1/0.01 100 Enabled ●/●
0.01/0.01 80.0 Enabled
●/●
1/0.01 0 Enabled ●/●
1/0.01 100 Enabled
●/●
1/0.01 0 Enabled ●/●
0.01/0.01 0.0 Enabled
●/●
1/0.01 100 Enabled ●/●
0.01/0.01 80.0 Enabled
●/●
1/0.01 0 Enabled ●/●
1/0.01 100 Enabled
●/●
1/0.01 0 Enabled ●/●
0.01/0.01 0.0 Enabled ●/●
1/0.01 100 Enabled ●/●
0.01/0.01 80.0 Enabled ●/●
1/0.01 0 Enabled
●/●
1/0.01 100 Enabled ●/●
Vector control
V/f Reference
Torque Position
Constant section
control control
− − ● 6.6.1
7.3.2
●/● − ●
●/● − ● 7.3.2
7.3.2
●/● − ●
− − ● 7.3.2
6.21.1
●/● − −
●/● − − 6.21.1
6.61
− − ●
− − ● 6.6.1
7.2.4
●/● − ●
●/● − ● 7.3.1
7.3.1
− − ●
●/● − ● 7.3.1
7.3.1
− − ●
●/● − − 6.21.1
6.21.1
●/● − −
●/● − ● 7.3.3
7.3.3
− − ●
●/● − ● 7.3.3
7.3.3
− − ●
●/● − − 6.21.1
6.21.1
●/● − −
●/● − ● ※
− − ● ※
●/● − ● ※
− − ● ※
●/● − ● ※
●/● − ● ※