Toshiba TOSVERT VF-P7 Instruction Manual page 204

1. Basic parameters (2/2)
Communi
Title Function
cation No.
Forward/reverse selection
0008

(At panel control only)
0009 Acceleration time #1

 0010 Deceleration time #1
0011 Maximum frequency

 0012 Upper limit frequency
0013 Lower limit frequency

 0014 Base frequency #1
Motor control mode
 0015
selection
0016 Manual torque boost

Selection of electronic
thermal protection
 0017
characteristics
 0018 Preset-speed #1
0019 Preset-speed #2

 0020 Preset-speed #3
0021 Preset-speed #4

 0022 Preset-speed #5
0023 Preset-speed #6

 0024 Preset-speed #7

Extended parameter
∼ −

Automatic edit function
 −
* Minimum setup unit is 0.1 in case of 16-bit access. Sensorless vector/vector with sensor (
Adjustment range
0: Forward,
1: Reverse
0.1()∼6000 [s]
0.1()∼6000 [s]
30.0∼400.0 [Hz]
0.0∼ [Hz]
0.0∼ [Hz]
25.0 ∼400.0 [Hz]
0: Constant torque
1: Variable torque mode
2: Automatic torque boost
3: Sensorless vector control (speed)
4: Automatic torque boost + automatic energy-saving
5: Sensorless vector control (speed) + automatic energy-saving
6: V/f 5-points setting
7:Sensorless vector control (speed/torque switching)
8: PG feedback vector control (speed/torque switching)
9: PG feedback vector control (speed/position switching)
0∼30%
Overload
Setting Overload stall
Type
protection
0 protect not stall
1 Standard protect
motor
2 not protect not stall
3 not protect
4 protect not stall
VF motor
5 protect
(special
6 not protect not stall
motor)
7 not protect
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
Setting of extended parameters listed on the
following pages
To search parameters different from default value
Min. unit (panel/ Default Write during
communication) setting running
0 Enabled
−
0.01/0.01* See J-28 Enabled
0.01/0.01* See J-28 Enabled
0.01/0.01 80 Disabled
0.01/0.01 80 Enabled
0.01/0.01 0.0 Enabled
0.01/0.01 60 Enabled
− 0 Disabled
0.1/0.01 See J-28 Enabled
stall
− 0 Disabled
stall
stall
stall
0.01/0.01 0.0 Enabled
0.01/0.01 0.0 Enabled
0.01/0.01 0.0 Enabled
0.01/0.01 0.0 Enabled
0.01/0.01 0.0 Enabled
0.01/0.01 0.0 Enabled
0.01/0.01 0.0 Enabled
− − −
− − −
● −
:valid, :invalid)
Vector control
V/f Reference
Speed Torque Position
Constant section
control control control
●/● ●/● −/● ●
●/● − − ●
●/● − − ●
●/● ●/● −/● ●
●/● − − ●
●/● − − ●
●/● ●/● −/● ●
−／− −／− −／− ●
−／− −／− −／− ●
●／− −／− −／− −
●／− −／− −／− −
●／− −／− −／− −
●／− −／− −／− −
−／− −／− −／− ●
●／− ●／− −／− ―
−／● −／● −／− −
−／● −／− −／● ―
− − − ●
●/● ●/● −/● ●
●/● − − ●
●/● − − ●
●/● − − ●
●/● − − ●
●/● − − ●
●/● − − ●
●/● − − ●
●/● ●/● −/● ●
●/● ●/● −/● ●
5.6
5.1.2
5.1.2
5.7
5.8
5.8
5.9
5.10
5.12
5.13
5.14
4.1.2
4.1.3