Table of Contents
Advertisement
Programming the Control Panel
Displaying User Information
Each user is identified by the alarm system as User 1 through to
User 8. Every user may view their User Number (1 - 8) or their own
Access Level as follows:
Displaying Your User Number
From
the
Programming
corresponding to your User Number will show
Zon es
U n set
1 2 3 4 5 6 7 8
T am p er
Press
, the system will then automatically revert to the
Programming Menu.
Displaying Your Access Level
From
the
Programming
corresponding to your Access Level will show
Zon es
U n set
1 2 3 4 5 6 7 8
T am p er
Press
, the system will then automatically revert to the
Programming Menu.
The Communicator Interface
The Control Panel features an eight output channel digital
communicator interface with Line Monitor (L/M) and Remote Reset
(R/R) inputs. The polarity of the outputs and the R/R input is
programmable.
The L/M input should be connected to 0V (AUX-) if not
required, otherwise Bell Delay will not operate.
Programming Communicator Selections
From the Programming Menu, enter
the options currently selected.
Zon es
U n set
1 2 3 4 5 6 7 8
T am p er
Press the appropriate numbered button(s) to select or de-
select the corresponding option(s) as shown on the display.
To display an explanation of the Comm. options associated
with
a
particular
corresponding key
Press
. The system will chime to confirm that the new
options have been accepted. The system will then automatically
revert to the Programming Menu.
34
&
Menu,
enter
.
The
Menu,
enter
.
The
-
. The display will show
number,
press
and
hold
(LCD Keypad only).
Option
1
Communicator
System is Reset
2
Line Monitor Input causes Tamper Alarm
zone
on Line Cut
3
Invert Communicator Outputs (off =
active low, on = active high)
4
Invert Remote Reset Input (off = active if
negative
negative applied)
5
Remote Reset Input Silences Internal
zone
Sounder during Alarm
6
Remote Reset Input Clears Engineer
Reset (see page 21)
7
Silent PA
8
Enable 90 Second Abort Time Limit
Option 1 - Communicator Outputs Latch Until Reset
When 'ON' ALL of the communicator outputs latch until the system
is reset, instead of activating for 2 seconds.
Do not use non-latching communicator outputs if selecting
Automatic Omit (see page 22).
Option 2 - Line Monitor Input Causes Tamper
When 'ON' a line fault condition causes a Tamper alarm.
The L/M input should be connected to 0V (AUX-) if not
required, otherwise Bell Delay will not operate.
Option 3 - Invert Communicator Outputs
When 'ON' ALL of the communicator outputs are inverted from 0V
applied on activation to 0V removed on activation.
Option 4 - Invert Remote Reset Input
When 'ON' the operation of the R/R input is inverted from 0V to
reset to 12V to reset.
Option 5 - Remote Reset Input Silences Sounders
When 'ON' the R/R input can be used to silence the internal
sounder during an alarm (except a fire alarm) to facilitate Audio
Verification (A/V).
the
Option 6 - Remote Reset Input Clears Engineer Reset
When 'ON' activating the R/R input will clear perform an Engineer
Reset (see page 21).
It is valid to select both Options 5 and 6 if required.
Option 7 - Silent PA
When 'ON' PA zones (see page 25) have a silent response (just
activation of the PA channel on the communicator interface with
no local audible or visible alarm response at all).
Option 8 - Enable 90 Second Abort Time
When 'ON' the system will only send an abort if a valid code is
entered within 90 seconds of an alarm activation. When 'OFF' the
system will send an abort whenever a valid code is first entered
after an alarm activation.
Veritas R8 Plus & Excel Installation Manual
Communicator Selections
Outputs
Latch
removed,
on
=
active
Factory
Setting
until
On
Off
Off
Off
if
Off
Off
Off
On
INS045-14
Advertisement
Table of Contents
