EWM T5.00-AC/DC Comfort 3.0 Operating Instructions Manual page 4

Contents
Notes on using these operating instructions
5.1.9
5.1.10
5.1.11
5.1.12
5.1.13
5.1.14
5.1.15
5.1.16
5.2 MMA welding ........................................................................................................................ 55
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
5.3 Arc length restriction (USP).................................................................................................. 58
5.3.1
5.4 Managing welding tasks (JOB manager) ............................................................................. 60
5.4.1
5.4.2
5.5 Power-saving mode (Standby) ............................................................................................. 61
5.6 Access control ...................................................................................................................... 61
5.7 Voltage reducing device ....................................................................................................... 62
5.8 Dynamic power adjustment .................................................................................................. 62
5.9 Synchronous welding (AC)................................................................................................... 62
5.10 Machine configuration menu ................................................................................................ 63
5.10.1
6 Maintenance, care and disposal ................................................................................................. 69
6.1 General................................................................................................................................. 69
6.2 Disposing of equipment ........................................................................................................ 70
7 Rectifying faults............................................................................................................................ 71
7.1 Warnings .............................................................................................................................. 71
7.2 Error messages (power source) ........................................................................................... 73
7.3 Resetting welding parameters to the factory settings .......................................................... 79
7.4 Software version of the machine control .............................................................................. 79
8 Appendix ....................................................................................................................................... 80
8.1 Parameter overview - setting ranges .................................................................................. 80
8.1.1
4
TIG activArc welding ............................................................................................. 41
TIG antistick .......................................................................................................... 41
Pulse welding ........................................................................................................ 42
Average value pulse welding ................................................................................ 42
5.1.12.1 Thermal pulsing ..................................................................................... 43
5.1.12.2 Automated pulses .................................................................................. 43
5.1.12.3 AC special ............................................................................................. 44
5.1.12.4 Pulsing in an upslope/downslope .......................................................... 44
Welding torch (operating variants) ........................................................................ 45
5.1.13.1 Welding torch mode .............................................................................. 45
5.1.13.2 Tapping function (tap torch trigger) ....................................................... 48
5.1.13.3 Up/down speed ..................................................................................... 48
5.1.13.4 Current jump .......................................................................................... 48
RTF 1 foot-operated remote control ..................................................................... 48
5.1.14.1 Working area ......................................................................................... 48
5.1.14.2 Response .............................................................................................. 49
5.1.14.3 Start program ........................................................................................ 49
5.1.14.4 End program .......................................................................................... 50
5.1.14.5 Start/stop operation ............................................................................... 50
Expert menu (TIG) ................................................................................................ 51
Aligning the cable resistance ................................................................................ 53
Welding task selection .......................................................................................... 55
Hotstart ................................................................................................................. 55
5.2.2.1 Selection and adjustment ...................................................................... 55
Arcforce................................................................................................................. 56
Antistick................................................................................................................. 56
Welding current polarity reversal (polarity reversal) ............................................. 57
AC welding ............................................................................................................ 57
5.2.6.1 Automatic AC frequency ........................................................................ 57
Pulse welding ........................................................................................................ 58
5.2.7.1 Average value pulse welding ................................................................ 58
JOB favourites ...................................................................................................... 59
5.3.1.1 Saving current settings to Favourites .................................................... 59
5.3.1.2 Loading saved Favourites ..................................................................... 59
5.3.1.3 Deleting saved Favourites ..................................................................... 60
Copying welding tasks (JOB) ............................................................................... 60
Reset welding task (JOB) to the factory setting ................................................... 61
Selecting, changing and saving parameters......................................................... 63
TIG welding ........................................................................................................... 80
8.1.1.1 Pulse parameters .................................................................................. 81
8.1.1.2 AC parameters ...................................................................................... 81
099-00T500-EW501
30.1.2023