Table of Contents
Advertisement
8)
Press asqw to select [COMMAND].
9)
Press the <ENTER> button.
f The [COMMAND] detailed screen is displayed.
10) Press as to select a [COMMAND].
f For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time
you press qw.
f When [INPUT] is selected, press the <ENTER> button, and then press asqw to select the input to be
set.
[COMMAND]
[POWER ON]
[STANDBY]
[SHUTTER]
[INPUT]
[OPERATING MODE]
*1 This item can be selected when the optional 12G-SDI Terminal Board (Model No.: TY-SB01QS) is installed in <SLOT>.
*2 This item can be selected when the optional Function Board for 12G-SDI Optical Fiber (Model No.: TY-SB01FB) is installed in <SLOT>.
*3 This item can be selected when the optional DIGITAL LINK Terminal Board (Model No.: TY-SB01DL) is installed in <SLOT>.
*4 This item can be selected when the optional Wireless Presentation System Receiver Board (Model No.: TY-SB01WP) is installed in <SLOT>.
*5 This item can be selected when the Function Board by other manufacturers is installed in <SLOT>.
*6 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK IN/
LAN> terminal of the optional DIGITAL LINK Terminal Board (Model No.: TY-SB01DL) installed in <SLOT>, its input name is automatically
reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
*7 If you change the settings while using the projector, the duration until the luminance decreases by half may shorten or the luminance may
decrease.
11) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 194)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
196 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
―
―
[OPEN]
[CLOSE]
[HDMI1]
[HDMI2]
[DisplayPort]
[SDI [SLOT]]
*1
[SDI OPT1 [SLOT]]
[SDI OPT2 [SLOT]]
[DIGITAL LINK [SLOT]]
[PressIT [SLOT]]
[SLOT]
*5
[INPUT1] - [INPUT10]
[NORMAL]
[ECO]
[USER1]
*7
[USER2]
[USER3]
Switches on the projector.
Enters standby.
Disables the shutter function (shutter: opened).
Enables the shutter function (shutter: closed).
Switches the input to HDMI1.
Switches the input to HDMI2.
Switches the input to DisplayPort.
Switches the input to SDI.
Switches the input to SDI OPT1.
*2
Switches the input to SDI OPT2.
*2
Switches the input to DIGITAL LINK.
*3
Switches the input to PressIT.
*4
Switches the input to SLOT.
Switches the input to DIGITAL LINK, and switches the input of the
*6
DIGITAL LINK output supported device to the specified input.
Prioritizes brightness.
Prioritizes the life of the light source.
Controls the power with the setting set to [USER1].
Controls the power with the setting set to [USER2].
Controls the power with the setting set to [USER3].
Description
Advertisement
Table of Contents
