Page 1 RAM 2500/3500 20 2 0 OWNER’ S M ANUAL...
Page 2 This Owner’s Manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment that are no longer available or were not ordered on this vehicle.
Page 3 TABLE OF CONTENTS INTRODUCTION ................9 GETTING TO KNOW YOUR VEHICLE.
Page 4: Table Of Contents
INTRODUCTION To Exit Remote Start Mode And Drive The Heated Seats — If Equipped ... . 30 Vehicle ......20 Ventilated Seats —...
Page 5 HOOD ......58 TRI-FOLD TONNEAU COVER — IF EQUIPPED ..79 Automatic Headlights —...
Page 6 ENGINE BREAK-IN RECOMMENDATIONS — Yellow Indicator Lights ....107 STARTING AND OPERATING DIESEL ENGINE ....170 Green Indicator Lights .
Page 7 Driving In Snow, Mud And Sand ..192 To Resume ..... 209 LaneSense Warning Message .
Page 8 Over The Road Operation With Snowplow Reinstalling The Jack And Tools ..272 6.7L Diesel Engine — Six-Speed AISIN Attached ..... . 246 Hub Caps/Wheel Covers —...
Page 9 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . 330 SAFETY AND GENERAL INFORMATION ..387 Transfer Case ....310 Torque Specifications .
Page 10 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ..... 404 Prepare For The Appointment ..404 Prepare A List .
Page 11 FCA US LLC aims at a constant improvement of the vehicles produced. For this reason, it reserves the right to make changes to the model described for technical and/or commercial reasons. For further information, contact an authorized dealer. When it comes to service, remember that authorized dealers know your Ram best, have factory-trained technicians and genuine MOPAR® parts, and care about your satisfaction.
Page 12: How To Use This Manual
INTRODUCTION HOW TO USE THIS MANUAL VAN CONVERSIONS/CAMPERS The New Vehicle Limited Warranty does not apply to body modifications or special ESSENTIAL INFORMATION equipment installed by van conversion/camper manufacturers/body builders. US resi- dents refer to your Warranty Information Book. Canadian residents refer to the “What Consult the Table of Contents to determine which section contains the information you Is Not Covered”...
Page 13 INTRODUCTION A — Forward Limit of Camper CG B — Rearward Limit of Camper CG When the truck is used to carry a slide-in camper, the total cargo load of the truck con- Secure loose items to prevent weight shifts that could affect the balance of your sists of the manufacturer’s camper weight figure, the weight of installed additional vehicle.
Page 14: Vehicle Modifications/Alterations
INTRODUCTION NOTE: These ratings are also provided on the vehicle certification label located on the driver’s side B-pillar. See “Vehicle Loading” in “Starting And Operating” for more information. For any additional instructions, please contact your conversion/camper manufacturer or an authorized dealer. VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthi-...
Page 15: Vehicle User Guide - If Equipped
GETTING TO KNOW YOUR VEHICLE • VEHICLE USER GUIDE — IF EQUIPPED Maintenance schedules and information • When viewing a topic, tap the star icon to add it to your Comprehensive icon and symbol glossary Favorites, for easy access in the future. Access your Owner’s Information right through your •...
Page 16 GETTING TO KNOW YOUR VEHICLE To Unlock The Doors And Tailgate Using The Panic Alarm Push and release the unlock button on the key fob once To turn the Panic Alarm feature on or off, push the to unlock the driver’s door. Push the unlock button Panic button on the key fob.
Page 17 GETTING TO KNOW YOUR VEHICLE NOTE: Alternative Back Cover Removal Method: 1. Remove the emergency key by pushing and holding the release button located on the side of the key fob When replacing the battery, ensure the (+) sign on The back cover of the key fob can also be removed by while pulling the emergency key out with your other the battery is facing upward.
Page 18: Ignition Switch
GETTING TO KNOW YOUR VEHICLE General Information IGNITION SWITCH The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: KEYLESS PUSH BUTTON IGNITION This device complies with Part 15 of the FCC Rules and This feature allows the driver to operate the ignition with Innovation, Science and Economic Development switch with the push of a button as long as the Remote Canada license-exempt RSS standard(s).
Page 19: Remote Start - If Equipped (Gasoline)
GETTING TO KNOW YOUR VEHICLE REMOTE START — IF EQUIPPED be used to operate the ignition switch. Put the nose WARNING! side (side opposite of the emergency key) of the key fob against the START/STOP ignition button and push to (GASOLINE) •...
Page 20: Remote Start Abort Message
GETTING TO KNOW YOUR VEHICLE • If an engine fault is present or fuel level is low, the REMOTE START COMFORT WARNING! vehicle will start and then shut down in 10 seconds. SYSTEMS — IF EQUIPPED • • The parking lights will turn on and remain on during Do not start or run an engine in a closed garage or When Remote Start is activated, the heated steering Remote Start mode.
Page 21: Remote Start - If Equipped (Diesel)
GETTING TO KNOW YOUR VEHICLE 2. l'utilisateur de l'appareil doit accepter tout brouillage HOW TO USE REMOTE START REMOTE START ABORT MESSAGE radioélectrique subi, même si le brouillage est sus- All of the following conditions must be met before the The following messages will display in the instrument ceptible d'en compromettre le fonctionnement.
Page 22: To Exit Remote Start Mode Without Driving The Vehicle
GETTING TO KNOW YOUR VEHICLE • Additional features, such as windshield wipers, will REMOTE START COMFORT bulb check, it indicates that someone attempted to also not be available while the vehicle is in the start the engine with an invalid key fob. In the event SYSTEMS —...
Page 23: General Information
GETTING TO KNOW YOUR VEHICLE L'exploitation est autorisée aux deux conditions TO ARM THE SYSTEM CAUTION! suivantes: Follow these steps to arm the Vehicle Security Alarm: • Always remove the key fobs from the vehicle and 1. l'appareil ne doit pas produire de brouillage, et 1.
Page 24: Rearming Of The System
GETTING TO KNOW YOUR VEHICLE 2. Grasp the Passive Entry door handle with a valid key DOORS WARNING! fob within 5 ft (1.5 m) of the Passive Entry door handle. If equipped, refer to "Keyless Enter-N-Go — • Do not leave children or animals inside parked MANUAL DOOR LOCKS Passive Entry"...
Page 25: Power Door Locks - If Equipped
GETTING TO KNOW YOUR VEHICLE • POWER DOOR LOCKS — POWER SIDE STEPS — IF EQUIPPED If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will IF EQUIPPED The Power Side Steps will extend a step for easier entry re-lock and if equipped will arm the security alarm.
Page 26 GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: To Lock The Vehicle’s Doors: Either the driver door only or all doors will unlock when With one of the vehicle’s Passive Entry key fobs within • After pushing the door handle lock button, you must you grab hold of the front driver’s door handle, depend- 5 ft (1.5 m) of the driver or passenger front door wait two seconds before you can lock or unlock the...
Page 27: Automatic Door Locks - If Equipped
GETTING TO KNOW YOUR VEHICLE Automatic Doors Unlock Programming 2. l'utilisateur de l'appareil doit accepter tout brouillage WARNING! radioélectrique subi, même si le brouillage est sus- — If Equipped ceptible d'en compromettre le fonctionnement. Avoid trapping anyone in the vehicle in a collision. The Automatic Doors Unlock feature can be enabled or La operación de este equipo está...
Page 28: Programming The Memory Feature
GETTING TO KNOW YOUR VEHICLE NOTE: 2. Adjust all memory profile settings to desired prefer- 3. Once the profile has been recalled, push and ences (i.e., driver’s seat, outside mirrors, adjustable release the set (S) button on the memory switch. •...
Page 29: Programming The Memory Feature
GETTING TO KNOW YOUR VEHICLE SEATS PROGRAMMING THE MEMORY 2. Select a desired memory profile, 1 or 2. FEATURE NOTE: Seats are a part of the Occupant Restraint system of If a memory profile has not already been set, refer To create a new memory profile, perform the following: the vehicle.
Page 30: Manual Adjustment Rear Seat
GETTING TO KNOW YOUR VEHICLE tion, lean forward and lift the lever. Release the lever MANUAL ADJUSTMENT REAR SEAT once the seatback is in the upright position. WARNING! Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision.
Page 31: Power Driver Seat Adjustment - If Equipped
GETTING TO KNOW YOUR VEHICLE Adjusting The Seat Up Or Down POWER DRIVER SEAT ADJUSTMENT CAUTION! — IF EQUIPPED The height of the seats can be adjusted up or down. Do not place any article under a power seat or Pull upward or push downward on the rear of seat Some models may be equipped with an eight-way impede its ability to move as it may cause damage to...
Page 32: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE • The distance the driver’s seat moves depends on where HEATED SEATS — IF EQUIPPED Press the heated seat button a second time to you have the driver’s seat positioned when you place turn the MED setting on. On some models, the front and rear seats may be the ignition in the OFF position.
Page 33: Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE VENTILATED SEATS — IF EQUIPPED This feature can be programmed through the Uconnect system. Refer to “Uconnect Settings” in “Multimedia” Front Ventilated Seats for further information. Located in the seat cushion are small fans that draw HEAD RESTRAINTS the air from the passenger compartment and move air through fine perforations in the seat cover to help keep...
Page 34: Front Head Restraint Removal
GETTING TO KNOW YOUR VEHICLE To raise the head restraint, pull upward on the head WARNING! restraint. To lower the head restraint, push the adjust- ment button, located at the base of the head restraint, • A loose head restraint thrown forward in a collision and push downward on the head restraint.
Page 35: Rear Head Restraint Removal
GETTING TO KNOW YOUR VEHICLE NOTE: STEERING WHEEL HEATED STEERING WHEEL — IF EQUIPPED • The rear center head restraint (Crew Cab) has only one adjustment position that is used to aid in the TILT STEERING COLUMN The steering wheel contains a heating element that routing of a tether.
Page 36: Driver Adjustable Pedals - If Equipped
GETTING TO KNOW YOUR VEHICLE WARNING! WARNING! • Persons who are unable to feel pain to the skin Do not adjust the pedals while the vehicle is moving. because of advanced age, chronic illness, diabe- You could lose control and have an accident. Always tes, spinal cord injury, medication, alcohol use, adjust the pedals while the vehicle is parked.
Page 37: Automatic Dimming Mirror - If Equipped
GETTING TO KNOW YOUR VEHICLE This mirror automatically adjusts for headlight glare from vehicles behind you. When the vehicle is placed into reverse gear, a video display illuminates to display the image generated by the rear view camera located on the tailgate handle. The auto dimming feature is also disabled to improve rear view viewing.
Page 38: Power Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE The power mirror controls consist of mirror select but- WARNING! tons and a four-way mirror control switch. To adjust a mirror, push either the L (left) or R (right) Vehicles and other objects seen in the passenger button to select the mirror that you want to adjust.
Page 39: Trailer Towing Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: If the Power Convex Mirror Switch is not pushed a sec- The Tilt Side Mirrors In Reverse feature is not turned on ond time, the switch will automatically default back to when delivered from the factory. the larger portion of the outside mirrors after a period This feature can be programmed through the Uconnect of time.
Page 40: Illuminated Vanity Mirror - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: ILLUMINATED VANITY MIRROR — IF EQUIPPED • The power fold mirrors are designed to operate while the vehicle is stationary or traveling at moder- Illuminated vanity mirrors are located on each sun visor. ate speeds. If you attempt to power fold the mirrors To use the mirror, rotate the sun visor down and swing at high speeds they may not fully open or close.
Page 41: Exterior Lights
GETTING TO KNOW YOUR VEHICLE NOTE: • If allowed by law in the country in which the vehicle was purchased, the Daytime Running Lights can be turned on and off using the Uconnect system, refer to “Uconnect Settings” in “Multimedia” for further information.
Page 42: Flash-To-Pass
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: 3. Push the multifunction lever away from you (toward front of vehicle) to engage the high beam mode. The engine must be running before the headlights will • The Automatic High Beam Headlamp Control can be come on in the Automatic mode.
Page 43: Headlights On With Wipers
GETTING TO KNOW YOUR VEHICLE HEADLIGHTS ON WITH WIPERS FRONT FOG LIGHTS — IF EQUIPPED LANE CHANGE ASSIST — (AVAILABLE WITH AUTOMATIC IF EQUIPPED To activate the front fog lights, turn on the parking lights or low beam headlights and push in the center of the HEADLIGHTS ONLY) Tap the multifunction lever up or down once, without headlight switch control knob.
Page 44: Battery Saver
GETTING TO KNOW YOUR VEHICLE When these lights are activated using the button on the INTERIOR LIGHTS headlight switch, the trailer spotter lights will remain illuminated when the vehicle transmission is in PARK, COURTESY LIGHTS NEUTRAL, or REVERSE. The trailer spotter lights will turn off when the vehicle transmission is placed in The courtesy, dome, cargo, and bed lights are turned on DRIVE.
Page 45: Illuminated Entry
GETTING TO KNOW YOUR VEHICLE Dimmer Controls NOTE: This feature also turns on the puddle lamps located beneath the outside mirrors (if equipped). On vehicles equipped with an LED overhead console, if The dimmer controls are part of the headlight switch both the Dome On and Dome Defeat buttons are The lights will fade to off after approximately 30 sec- and are located on the left side of the instrument...
Page 46: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: Rotate the end of the lever upward, to the first detent To prevent freeze-up of your windshield washer system past the intermittent settings for low-speed wiper in cold weather, select a solution or mixture that meets This feature can be programmed on/off through the operation.
Page 47: Climate Controls
GETTING TO KNOW YOUR VEHICLE Transmission In NEUTRAL Position — When the igni- • CLIMATE CONTROLS MANUAL CLIMATE CONTROL tion is ON, and the transmission is in the NEUTRAL OVERVIEW position, the Rain Sensing system will not operate The Climate Control system allows you to regulate the until the wiper switch is moved, vehicle speed is temperature, air flow, and direction of air circulating greater than 5 mph (8 km/h), or the gear selector is...
Page 48 GETTING TO KNOW YOUR VEHICLE Icon Description Recirculation Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the system between Recirculation mode and outside air mode. The Recirculation indicator and the A/C indicator illuminate when the Recirculation button is pushed. Recirculation can be used when outside conditions, such as smoke, odors, dust, or humidity are present.
Page 49 GETTING TO KNOW YOUR VEHICLE Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. Floor Mode Floor Mode Air comes from the floor outlets.
Page 50: Automatic Climate Control Overview
GETTING TO KNOW YOUR VEHICLE Icon Description Climate Control OFF To turn the Climate Controls off, turn the Blower Control knob to the O (off) position. AUTOMATIC CLIMATE CONTROL OVERVIEW Uconnect 4C NAV With 12-inch Display Automatic Temperature Controls NOTE: Icons and descriptions can vary based upon vehicle Uconnect 4/4C/4C NAV With 8.4-inch Display Automatic equipment.
Page 51 GETTING TO KNOW YOUR VEHICLE Icon Description MAX A/C Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air. The MAX A/C indicator illumi- nates when MAX A/C is on. Pressing the button again will cause the MAX A/C operation to exit. NOTE: The MAX A/C button is only available on the touchscreen.
Page 52 GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Auto Button AUTO Set your desired temperature and press AUTO. AUTO will achieve and maintain your desired temperature by automatically adjusting the blower speed and air distribution. AUTO mode is highly recommended for efficiency. You can press and release this button on the touchscreen, or push Touchscreen Auto Button the button on the faceplate, to turn AUTO on.
Page 53 GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Temperature Knobs Driver and Passenger Temperature Up and Down Buttons Provides the driver and passenger with independent temperature control. Push the red button (or rotate knob if equipped) on the faceplate or touchscreen, or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.
Page 54 GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Blower Knob Blower Control Blower Control regulates the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen. •...
Page 55 GETTING TO KNOW YOUR VEHICLE Icon Description Panel Mode Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction. There is a shut-off wheel located below the air vanes to shut off or adjust the amount of airflow from these outlets.
Page 56: Climate Control Functions
GETTING TO KNOW YOUR VEHICLE NOTE: CLIMATE CONTROL FUNCTIONS In MAX A/C, the blower level and mode position can be adjusted to desired user settings. Pressing other set- • It is not necessary to move the temperature settings A/C (Air Conditioning) tings will cause the MAX A/C operation to switch to the for cold or hot vehicles.
Page 57: Windows
GETTING TO KNOW YOUR VEHICLE Winter Operation WEATHER CONTROL SETTINGS CAUTION! To ensure the best possible heater and defroster perfor- Cool & Humid Set the mode control to • Do not use scrapers, sharp instruments, or abra- mance, make sure the engine cooling system is func- Conditions position and turn on to...
Page 58 GETTING TO KNOW YOUR VEHICLE Auto-Up Feature With Anti-Pinch passenger window control and on the rear doors for 2. Pull the window switch up to close the window com- rear window control. The windows will operate when the Protection — If Equipped pletely and continue to hold the switch up for an ignition switch is placed in the ON/RUN or ACC position, additional two seconds after the window is closed.
Page 59: Wind Buffeting
GETTING TO KNOW YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! • In a collision, there is a greater risk of being thrown SINGLE PANE POWER SUNROOF from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten The power sunroof switches are located on the over- your seat belt properly and make sure all passen- head console between the courtesy/reading lights.
Page 60: Hood
GETTING TO KNOW YOUR VEHICLE Closing Sunroof Pinch Protect Feature HOOD Express This feature will detect an obstruction in the closing of the sunroof during the Express Close operation. If an Push the switch forward and release it within one-half TO OPEN THE HOOD obstruction in the path of the sunroof is detected, the second and the sunroof will close automatically from...
Page 61: To Close The Hood
GETTING TO KNOW YOUR VEHICLE TAILGATE BED STEP — IF EQUIPPED Your vehicle may be equipped with an extendable bed step on the driver’s side of the tailgate to provide easier OPENING entry and exit into the truck bed. The power tailgate may be opened by pushing the tail- gate release pad located on the tailgate door.
Page 62: Garage Door Opener - If Equipped
GETTING TO KNOW YOUR VEHICLE To extend the bed step, place your foot on the protrud- GARAGE DOOR OPENER — IF EQUIPPED WARNING! ing foot tab located on the left edge of the bed step, and push rearward. A small amount of force will release required by Federal safety standards.
Page 63 GETTING TO KNOW YOUR VEHICLE NOTE: 1. Place the ignition in the ON/RUN position. To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT 2. Place the hand-held transmitter 1 to 3 inches (3 to •...
Page 64: Canadian/Gate Operator Programming
GETTING TO KNOW YOUR VEHICLE Reprogramming A Single HomeLink® Button 5. Press and hold the programmed HomeLink® button It may be helpful to unplug the device during the cycling (Canadian/Gate Operator) and observe the indicator light. process to prevent possible overheating of the garage ○...
Page 65: Troubleshooting Tips
GETTING TO KNOW YOUR VEHICLE NOTE: TROUBLESHOOTING TIPS GENERAL INFORMATION Changes or modifications not expressly approved by the If you are having trouble programming HomeLink®, The following regulatory statement applies to all Radio party responsible for compliance could void the user’s here are some of the most common solutions: Frequency (RF) devices equipped in this vehicle: authority to operate the equipment.
Page 66 GETTING TO KNOW YOUR VEHICLE If equipped with a covered upper glove compartment, WARNING! push the release button to open. To open the lower glove compartment, pull the release • This armrest is not a seat. Anyone seated on the handle.
Page 67 GETTING TO KNOW YOUR VEHICLE Push the release button at the front of the cupholder bin to slide tray rearward for access of front lower stor- age bin, or forward to access the rear lower storage bin with the center console lid in the open position. Center Console Tandem Doors —...
Page 68 GETTING TO KNOW YOUR VEHICLE Seatback Storage — If Equipped Storage Bin (Regular Cab) — If Equipped Located in the back of both the driver and passenger The storage bin is located behind the front seats and front seats are pockets that can be used for storage. runs the length of the cab.
Page 69 GETTING TO KNOW YOUR VEHICLE Unfolding The Load Floor/Crew Cab 3. Lift the front panel until the load floor unfolds into WARNING! position. 1. Lift the 60/40 seat cushion(s) to the upward Do not drive with the load floor in the up position. position.
Page 70: Cupholders
GETTING TO KNOW YOUR VEHICLE Below Rear Seat Storage (Crew Cab) — CUPHOLDERS If Equipped Front Seat Cupholders The Crew Cab models provide additional storage under For vehicles equipped with a center console, two cup- the rear seats. Lift the seats to access the storage holders are located in front of the console storage bin.
Page 71: Electrical Power Outlets
GETTING TO KNOW YOUR VEHICLE When the vehicle is turned off, be sure to unplug any CAUTION! equipment as to not drain the battery of the vehicle. All • accessories connected to the outlet(s) should be Power outlets are designed for accessory plugs removed or turned off when the vehicle is not in use to only.
Page 72: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE POWER INVERTER — IF EQUIPPED If equipped, a 115 Volt (400 W maximum) inverter may be located inside the center console toward the right hand side, just under the Wireless Charging Pad (if equipped). This inverter can power cellular phones, electronics and other low power devices requiring power up to 400 W.
Page 73: Wireless Charging Pad - If Equipped
GETTING TO KNOW YOUR VEHICLE WIRELESS CHARGING PAD — Place the device inside the prepared area delimited in the mat as shown in the image. Incorrect positioning IF EQUIPPED will prevent the phone from charging. LED Indicator Status: • No Light: Charging pad is idle or searching for a device.
Page 74: Overhead Sunglass Storage
GETTING TO KNOW YOUR VEHICLE • iPhone® 12 (including iPod®) is equipped with soft- PICKUP BOX CAUTION! ware to protect the device from overheating. When the software is active, the rate of charge is slowed The key fob should not be placed on the charging pad The pickup box has many features designed for utility down to protect the device.
Page 75: Cargo Camera - If Equipped
GETTING TO KNOW YOUR VEHICLE Activation CARGO CAMERA — IF EQUIPPED WARNING! The Dynamic Centerline feature can be activated Your vehicle may be equipped with the Cargo Camera • through the Uconnect settings by pressing the Cargo The pickup box is intended for load carrying pur- that allows you to see an image of the inside of the Camera soft button, followed by the “Adjust Centerline”...
Page 76: Rambox - If Equipped
GETTING TO KNOW YOUR VEHICLE • The touchscreen button “X” to disable the display of There will also be a 115 Volt (400 Watt) power inverter To open a storage bin with the RamBox unlocked, push the camera image is made available ONLY when the located in the RamBox.
Page 77: Rambox Safety Warning
GETTING TO KNOW YOUR VEHICLE RamBox Storage Bin Cover Emergency CAUTION! Release Lever — If Equipped • Ensure cargo bin lids are closed and latched As a security measure, a Storage Bin Cover Emergency before moving or driving vehicle. Release is built into the storage bin cover latching •...
Page 78 GETTING TO KNOW YOUR VEHICLE Storage Position The storage position for the bed divider is at the front of the truck bed which maximizes the bed cargo area when not in use. To install the bed divider into the storage position, per- form the following: 1.
Page 79: Bed Rail Tie-Down System - If Equipped
GETTING TO KNOW YOUR VEHICLE BED RAIL TIE-DOWN SYSTEM — To move the cleat to any position on the rail, turn the nut counterclockwise several turns. Then pull out on IF EQUIPPED the cleat and slide it to the detent nearest the desired location.
Page 80: Easy-Off Tailgate
GETTING TO KNOW YOUR VEHICLE End Cap Screw Location If Equipped With Tonneau Cover Pull End Cap Away From Rail Connector Bracket Location Cleat Removal (Without Tonneau Cover) EASY-OFF TAILGATE 2. Remove the connector bracket from the sill by push- ing inward in the locking tab.
Page 81: Removing The Tailgate
GETTING TO KNOW YOUR VEHICLE • 5. Connect the tailgate plug (provided in the glove com- 3. Position the tailgate on a 45 degree angle. Stowage strap partment) to the tailgate wiring harness to ensure • Locking capability 4. Raise the right side of the tailgate until the right side that the terminals do not corrode.
Page 82 GETTING TO KNOW YOUR VEHICLE CAUTION! Make sure the Tonneau Cover clamp and clamp wire are in the proper stowed position. If the clamp and clamp wire are not properly stowed, damage to the Tonneau Cover material will result. 4. Fold the rear panel up onto the center panel (inter- mediate position).
Page 83: Tri-Fold Tonneau Cover Installation
GETTING TO KNOW YOUR VEHICLE TRI-FOLD TONNEAU COVER INSTALLATION To install the Tonneau Cover follow the following steps: 1. Position the folded Tonneau Cover on the truck bed and push the cover forward against the front of the truck bed. The Tonneau Cover centers itself when placed on the vehicle.
Page 84 GETTING TO KNOW YOUR VEHICLE 4. Push clamp handles upward to the clamped position 6. Unfold the center and rear panels to the intermedi- to properly engage the clamps. ate position. Correct Folding — Hold Panels Together 7. Completely unfold the Tonneau Cover. Clamped Position Intermediate Position (Vehicle Cannot Be Driven) NOTE:...
Page 85: Tri-Fold Tonneau Cover Cleaning
GETTING TO KNOW YOUR VEHICLE Stowed Position Improper Clamp Position Locking Hole NOTE: 9. Push clamp wires up and under the flange of box (or TRI-FOLD TONNEAU COVER flange of RamBox rail, if equipped) to the semi Once clamped, be sure the clamps are not partially CLEANING clamped position.
Page 86: Base / Midline Instrument Cluster
GETTING TO KNOW YOUR INSTRUMENT PANEL BASE / MIDLINE INSTRUMENT CLUSTER — GAS ENGINE Base / Midline Instrument Cluster — Gas Engine...
Page 87: Getting To Know Your Instrument Panel
GETTING TO KNOW YOUR INSTRUMENT PANEL BASE / MIDLINE INSTRUMENT 6. Temperature Gauge 7. Fuel Gauge ○ ○ The gauge pointer shows engine coolant tem- The pointer shows the level of fuel in the fuel CLUSTER DESCRIPTIONS — GAS perature. The pointer positioned within the nor- tank when the ignition is in the ON/RUN ENGINE mal range indicates that the engine cooling sys-...
Page 88: Premium Instrument Cluster - Gas Engine
GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER — GAS ENGINE Premium Instrument Cluster — Gas Engine...
Page 89: Premium Instrument Cluster Descriptions - Gas Engine
GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER WARNING! DESCRIPTIONS — GAS ENGINE A hot engine cooling system is dangerous. You or oth- ers could be badly burned by steam or boiling cool- 1. Tachometer ant. You may want to call an authorized dealer for ○...
Page 90: Base Instrument Cluster - Diesel Engine
GETTING TO KNOW YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER — DIESEL ENGINE Base Instrument Cluster — Diesel Engine...
Page 91: Base Instrument Cluster Descriptions - Diesel Engine
GETTING TO KNOW YOUR INSTRUMENT PANEL ○ BASE INSTRUMENT CLUSTER 3. Instrument Cluster Display The DEF gauge may also not immediately update ○ after a refill if the temperature of the DEF fluid is When the appropriate conditions exist, this dis- DESCRIPTIONS —...
Page 92: Premium Instrument Cluster
GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER — DIESEL ENGINE Premium Instrument Cluster — Diesel Engine...
Page 93: Premium Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER gauge. You may not see any movement in the ment cluster display is designed to display important reading – even after driving up to 200 miles information about your vehicle’s systems and features. DESCRIPTIONS —...
Page 94: Oil Life Reset
GETTING TO KNOW YOUR INSTRUMENT PANEL • Left Arrow Button The system allows the driver to select information by pushing the following instrument cluster display control Push and release the left arrow button to buttons located on the left side of the steering wheel: access/select the information screens, submenu screens of a main menu item, or to return to the main menu.
Page 95: Display Menu Items
GETTING TO KNOW YOUR INSTRUMENT PANEL 6. Push and release the up arrow button to exit the Adaptive Cruise Control Ready directional prompts to access or reset any of the follow- instrument cluster display screen. ing Vehicle Info submenu items: When ACC is activated but the vehicle speed setting Secondary Method Of Resetting Engine Oil Life •...
Page 96 GETTING TO KNOW YOUR INSTRUMENT PANEL • Phone Call Status • Average Fuel Economy Value Driver Assist (Show/Hide) — If Equipped • • Range To Empty When a call is incoming, a Phone Call Status pop-up will Fuel Economy (Show/Hide) display on the screen.
Page 97 GETTING TO KNOW YOUR INSTRUMENT PANEL • • • Exhaust Brake — If Equipped Coolant Temperature — If Equipped Compass • • • Turbo Boost — If Equipped Oil Temperature — If Equipped Outside Temp • • • Fuel Filter Life — If Equipped Battery Voltage —...
Page 98 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: • Restore Defaults Trailer Brake • • Your vehicle may be equipped with the following Oil Pressure (Default Setting) Cancel (Default Setting) settings. • • Coolant Temperature Restore • • If equipped with a base radio (Non-Touchscreen) Oil Temperature Settings —...
Page 99 GETTING TO KNOW YOUR INSTRUMENT PANEL Setting Names Abbreviated Setting Names Submenus (Right Submenu Layer) (Left Submenu Layer) Remote Unlock Sequence Remote Unlock Driver Door; All Doors Key Fob Linked to Memory Key in Memory On; Off Passive Entry Passive Entry On;...
Page 100: Diesel Messages And Warnings - 6.7L Cummins Diesel Engine
GETTING TO KNOW YOUR INSTRUMENT PANEL Setting Names Abbreviated Setting Names Submenus (Right Submenu Layer) (Left Submenu Layer) Calibrate Compass Compass Cal Cancel; Calibrate Fuel Saver Display Fuel Saver On; Off Commercial Settings — If Equipped DIESEL MESSAGES AND The following messages may display in your instrument cluster display: WARNINGS —...
Page 101 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: By simply driving your vehicle at highway speeds for Engine speed may be briefly limited to 1000 RPM as little as 45 minutes, you can remedy the condi- after starting with coolant temperature below freez- Failing to follow the oil change indicator, changing tion in the particulate filter system and allow your ing conditions, and may be limited to 1000 RPM for...
Page 102 DEF system has been filled • 5 MPH Max Speed on Restart, Long Idle or Refuel Your vehicle is equipped with an advanced Ram Active with a fluid other than DEF, has experienced compo- Service DEF See Dealer — This message will con- Air system that provides enhanced performance, espe- nent failures, or when tampering has been detected.
Page 103: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL • BATTERY SAVER ON/BATTERY The electrical loads that may be switched off The battery was used for an extended period with (if equipped), and vehicle functions which can be the engine not running to supply radio, lights, char- SAVER MODE MESSAGE —...
Page 104: Red Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL tem check menu may appear different based upon turns on it may indicate that the parking brake is Vehicles equipped with the Anti-Lock Brake System equipment options and current vehicle status. Some applied, that the brake fluid level is low, or that there is (ABS) are also equipped with Electronic Brake Force telltales are optional and may not appear.
Page 105 GETTING TO KNOW YOUR INSTRUMENT PANEL Engine Coolant Temperature Warning Do not operate the vehicle until the cause is corrected. ON/RUN or ACC/ON/RUN position and remain on briefly Light This light does not indicate how much oil is in the as a bulb check.
Page 106: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Engine Check/Malfunction Indicator CAUTION! CAUTION! Warning Light (MIL) Continuous driving with the Transmission Tempera- Prolonged driving with the Malfunction Indicator Light The Engine Check/Malfunction Indicator ture Warning Light illuminated will eventually cause (MIL) on could cause damage to the vehicle control Light (MIL) is a part of an Onboard Diagnos- severe transmission damage or transmission failure.
Page 107 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) OFF Low Washer Fluid Warning Light Tire Pressure Monitoring System (TPMS) Warning Light — If Equipped Warning Light This warning light will illuminate when the windshield washer fluid is low. This warning light indicates the Electronic The warning light switches on and a mes- Stability Control (ESC) is off.
Page 108 GETTING TO KNOW YOUR INSTRUMENT PANEL Service Forward Collision Warning ing on a significantly underinflated tire causes the tire CAUTION! to overheat and can lead to tire failure. Underinflation (FCW) Light — If Equipped also reduces fuel efficiency and tire tread life, and may Aftermarket wheels can cause sensor damage.
Page 109: Yellow Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Cold Ambient Derate Mode Indicator Air Suspension Alternate Trailer Height YELLOW INDICATOR LIGHTS Light — If Equipped Indicator Light — If Equipped Forward Collision Warning Off Indicator This indicator light will illuminate when a This light will illuminate when the air suspen- Light —...
Page 110: Green Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Front And Rear Axle Lock Indicator Light 4WD High Indicator Light — If Equipped Water In Fuel Indicator Light — If Equipped This light indicates when the front, rear, or This light alerts the driver that the vehicle is both axles have been locked.
Page 111: White Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Automatic Diesel Exhaust Brake Front Fog Indicator Light — If Equipped WHITE INDICATOR LIGHTS Indicator Light — If Equipped This indicator light will illuminate when the Adaptive Cruise Control (ACC) Ready front fog lights are on. This indicator light will illuminate when the Light —...
Page 112: Blue Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Indicator Light — If Equipped It will also store diagnostic codes and other information WARNING! to assist your service technician in making repairs. When the LaneSense system is ON, but not Although your vehicle will usually be drivable and not •...
Page 113 GETTING TO KNOW YOUR INSTRUMENT PANEL Your vehicle has a simple ignition actuated test, which Regardless of whether your vehicle's OBD II system is you can use prior to going to the test station. To check if ready or not, if the MIL is illuminated during normal your vehicle's OBD II system is ready, you must do the vehicle operation you should have your vehicle serviced following:...
Page 114: Safety
SAFETY Anti-Lock Brake Warning Light SAFETY FEATURES WARNING! The yellow “Anti-Lock Brake Warning Light” will turn on • The ABS contains sophisticated electronic equip- when the ignition is placed in the ON/RUN mode and ANTI-LOCK BRAKE SYSTEM (ABS) ment that may be susceptible to interference may stay on for as long as four seconds.
Page 115 SAFETY Brake Assist System (BAS) If the “Brake System Warning Light” remains on or The “ESC Activation/Malfunction Indicator Light” comes on while driving, it indicates that the brake sys- located in the instrument cluster will start to flash as The Brake Assist System (BAS) is designed to optimize tem is not functioning properly and that immediate ser- soon as the ESC system becomes active.
Page 116 SAFETY WARNING! WARNING! WARNING! maintenance that reduces the effectiveness of the • • When in “Partial Off” mode, the TCS functionality In the ESC “Full Off” mode, the engine torque ESC system can increase the risk of loss of vehicle of ESC, except for the limited slip feature described reduction and stability features are disabled.
Page 117 SAFETY becomes active. The “ESC Activation/Malfunction Indi- or evasive driving maneuvers; it cannot prevent wheel 3. Active (feature is enabled and actively controlling cator Light” also flashes when TCS is active. If the “ESC lift due to other factors, such as road conditions, leav- vehicle speed) Activation/Malfunction Indicator Light”...
Page 118 SAFETY NOTE: Feedback To The Driver The following conditions must be met in order for HSA to activate: During HDC the +/- shifter input is used for HDC target The instrument cluster has an HDC icon and the HDC • speed selection, but will not affect the gear chosen by switch has an LED icon, which offers feedback to the The feature must be enabled.
Page 119 SAFETY Disabling And Enabling HSA Towing With HSA allow more engine power to be applied to the wheel that is not spinning. BLD may remain enabled even if This feature can be turned on or turned off. To change HSA will also provide assistance to mitigate roll back TCS and Electronic Stability Control (ESC) are in a the current setting, proceed as follows: while towing a trailer.
Page 120: Auxiliary Driving Systems
SAFETY AUXILIARY DRIVING SYSTEMS tion zones on both sides of the vehicle when the vehicle If the system detects degraded performance due to speed reaches approximately 6 mph (10 km/h) or contamination or foreign objects, a message will warn higher and will alert the driver of vehicles in these you of a blocked sensor and the warning indicators in BLIND SPOT MONITORING (BSM) —...
Page 121 SAFETY Entering From The Side Overtaking Traffic The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foli- Vehicles that move into your adjacent lanes from either If you pass another vehicle slowly with a relative speed age, berms, snow banks, car washes, etc.
Page 122 SAFETY Rear Cross Path (RCP) Blind Spot Alert Lights/Chime When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible When operating in Blind Spot Alert Lights/Chime mode, The Rear Cross Path (RCP) feature is intended to aid alarms, including reducing the radio volume.
Page 123 SAFETY Trailer Merge Assist NOTE: Selected setting is stored when the ignition is placed in NOTE: the OFF position. To change this setting, it must be When Trailer Merge Assist is activated, Rear Cross Path selected through the Uconnect Settings. Refer to “Uconnect Settings”...
Page 124 SAFETY NOTE: WARNING! Trailer length is determined within +/- 3 ft (1 m) of actual length. Trailers that are the same size as the The Blind Spot Monitoring system is only an aid to category limit, 10/20/30 ft (3/6/9 m), could be subject help detect objects in the blind spot zones.
Page 125: Forward Collision Warning (Fcw) With Mitigation - If Equipped
SAFETY • La operación de este equipo está sujeta a las mitigate the potential forward collision. If the driver The FCW alerts may be triggered on objects other siguientes dos condiciones: reacts to the warnings by braking and the system deter- than vehicles such as guard rails or sign posts mines that the driver intends to avoid the collision by based on the course prediction.
Page 126 SAFETY Turning FCW On Or Off FCW Braking Status And Sensitivity FCW Limited Warning The FCW button is located in the Uconnect display in The FCW sensitivity and Active Braking status are pro- If the instrument cluster displays “ACC/FCW Limited the control settings.
Page 127: Tire Pressure Monitoring System (Tpms)
SAFETY NOTE: Le présent appareil est conforme aux CNR d`Innova- radio will display a TPMS message, when this occurs tion, Science and Economic Development applicables you must increase the tire pressure to the recom- When filling warm tires, the tire pressure may need to aux appareils radio exempts de licence.
Page 128 SAFETY Tire Pressure Monitoring Low Pressure CAUTION! Warnings • After inspecting or adjusting the tire pressure The “Tire Pressure Monitoring Warning Light” always reinstall the valve stem cap. This will pre- will illuminate in the instrument cluster when vent moisture and dirt from entering the valve tire pressure is low in one or more of the four stem, which could damage the TPMS sensor.
Page 129 SAFETY NOTE: will also sound a chime. In addition, the instrument the instrument cluster will display a "SERVICE TPM cluster will display a “Tire Pressure Temporarily Unavail- SYSTEM" message for a minimum of five seconds When filling warm tires, the tire pressure may need to able”...
Page 130 With the sensors installed and the trailer near or con- sage will display on the radio indicating the process was nected to your Ram truck, initiate the pairing process by unsuccessful. Under certain circumstances, the double entering the settings menu in the radio and select horn chirp may continue to happen every three minutes trailer.
Page 131 SAFETY Should this occur, you should stop as soon as possible To correct this condition, the correct trailer number The hazard lamps will come on to confirm the vehicle is and inflate the tires with a low pressure condition must be selected in the radio. Refer to the “Uconnect in Tire Fill Alert mode.
Page 132 SAFETY • increments for each axle setting. XX = the vehicle’s cold The horn will chirp three times if the tire is over If a system fault is detected, the instrument cluster will placard pressure values for the front and rear axles as inflated or over deflated and will continue to chirp display a "SERVICE TPM SYSTEM"...
Page 133: Occupant Restraint Systems
SAFETY Le présent appareil est conforme aux CNR d`Innova- Some of the safety features described in this section 7. The driver and front passenger seats should be tion, Science and Economic Development applicables may be standard equipment on some models, or may moved back as far as practical to allow the front air aux appareils radio exempts de licence.
Page 134 SAFETY Lap/Shoulder Belts Research has shown that seat belts save lives, and they sequence starts by blinking the Seat Belt Reminder can reduce the seriousness of injuries in a collision. Light and sounding an intermittent chime. Once the All seating positions except the Mega Cab and Crew Some of the worst injuries happen when people are BeltAlert warning sequence has completed, the Seat Cab front center seating position have combination lap/...
Page 135 SAFETY Lap/Shoulder Belt Operating WARNING! WARNING! Instructions • or not an air bag is also provided at their seating A seat belt that is buckled into the wrong buckle 1. Enter the vehicle and close the door. Sit back and position to minimize the risk of severe injury or will not protect you properly.
Page 136 SAFETY 5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle.
Page 137 SAFETY 4. When the seat belt is long enough to fit, insert the WARNING! mini-latch plate into the mini-buckle until you hear a “click.” • Wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer 5.
Page 138 SAFETY First Row Center Lap Belt Operating WARNING! Instructions — If Equipped lap belt is not long enough and only use in the rec- The center seating position for the Mega Cab and Crew ommended seating positions. Remove and store Cab front seat has a lap belt only.
Page 139 SAFETY Seat Belt Pretensioner around the occupant’s mid-section so as to not activate the ALR. If the ALR is activated, you will hear a clicking The front outboard seat belt system is equipped with sound as the seat belt retracts. Allow the webbing to pretensioning devices that are designed to remove retract completely in this case and then carefully pull slack from the seat belt in the event of a collision.
Page 140: Supplemental Restraint Systems (Srs)
SAFETY 3. Allow the seat belt to retract. As the seat belt The air bag system must be ready to protect you in a the ON/RUN position. After the self-check, the Air Bag retracts, you will hear a clicking sound. This indi- collision.
Page 141 SAFETY Driver And Passenger Front Air Bag WARNING! Features on, stays on after you start the vehicle, or if it comes 2500 Series Truck on as you drive, have an authorized dealer service the air bag system immediately. The Advanced Front Air Bag system has multistage driver and front passenger air bags.
Page 142 SAFETY Supplemental Side Air Bags This vehicle may be equipped with a driver and/or front On the other hand, depending on the type and location passenger seat belt buckle switch that detects whether of impact, front air bags may deploy in crashes with Supplemental Seat-Mounted Side Air Bags (SABs) the driver or front passenger seat belt is buckled.
Page 143 SAFETY SABICs inflate with enough force to injure occupants if deploy independently; a left side impact deploys the left WARNING! they are not belted and seated properly, or if items are Side Air Bags only and a right-side impact deploys the positioned in the area where the SABICs inflate.
Page 144 SAFETY system will deploy the side air bags and seat belt pre- If you do have a collision which deploys the air bags, WARNING! tensioners on both sides of the vehicle. any or all of the following may occur: • •...
Page 145 SAFETY ○ NOTE: Horn WARNING! ○ Front wiper • ○ Air bag covers may not be obvious in the interior Headlamp washer pump the steering wheel hub trim cover or the upper pas- trim, but they will open during air bag deployment. senger side of the instrument panel.
Page 146: Child Restraints
SAFETY • How far (if at all) the driver was depressing the CHILD RESTRAINTS There are different sizes and types of restraints for chil- accelerator and/or brake pedal; and, dren from newborn size to the child almost large Everyone in your vehicle needs to be buckled up at all enough for an adult safety belt.
Page 147 SAFETY Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children 12 years old or younger, who have outgrown the Children Too Large for Child Restraints Vehicle Seat Belt, seated in a rear seat of the vehicle height or weight limit of their booster seat Infant And Child Restraints Older Children And Child Restraints WARNING!
Page 148 SAFETY against the seatback, should use the seat belt in a rear seat belt fit periodically and make sure the seat belt WARNING! seat. Use this simple 5-step test to decide whether the buckle is latched. A child’s squirming or slouching can child can use the vehicle’s seat belt alone: move the belt out of position.
Page 149 SAFETY Lower Anchors And Tethers For CHildren LATCH Positions For Installing Child (LATCH) Restraint System Restraints In This Vehicle Mega Cab LATCH Positions LATCH Label Top Tether Anchorage Symbol Regular Cab LATCH Positions Lower Anchorage Symbol (2 Anchorages Per Seat- Your vehicle is equipped with the child restraint anchor- ing Position) age system called LATCH, which stands for Lower...
Page 150 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage system until the combined weight of the What is the weight limit (child’s weight + weight of the child child and the child restraint is 65 lbs (29.5 kg). Use the seat belt restraint) for using the LATCH anchorage system to attach the child 65 lbs (29.5 kg) and tether anchor instead of the LATCH system once the combined...
Page 151 SAFETY Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
Page 152 SAFETY tether strap will have a hook at the end to attach to the 5. Tighten all of the straps as you push the child Always follow the directions of the child restraint top tether anchorage and a way to tighten the strap after manufacturer when installing your child restraint.
Page 153 SAFETY Systems” for additional information on ALR. The cinch- WARNING! ing latch plate is designed to hold the lap portion of the • seat belt tight when webbing is pulled tight and straight Child restraint anchorages are designed to with- through a child restraint’s belt path.
Page 154 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + weight of the child Always use the tether anchor when using the seat belt to install a restraint) for using the Tether Anchor with the seat belt to attach a Weight limit of the Child Restraint forward facing child restraint, up to the recommended weight limit forward facing child restraint?
Page 155 SAFETY Installing Child Restraints Using The Top 9. Test that the child restraint is installed tightly by 3. Slide the latch plate into the buckle until you hear a pulling back and forth on the child seat at the belt “click.”...
Page 156 SAFETY WARNING! Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.
Page 157 SAFETY NOTE: If there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connected to the center tether strap loop. This is the correct way to tether two out- board child seats.
Page 158: Transporting Pets
SAFETY 2. Attach both hooks to the center tether strap loop, TRANSPORTING PETS EXHAUST GAS but do not tighten the straps yet. Air Bags deploying in the front seat could harm your 3. Place a child restraint on the center rear seat. Route pet.
Page 159: Safety Checks You Should Make Inside The Vehicle
SAFETY Floor Mat Safety Information SAFETY CHECKS YOU SHOULD WARNING! MAKE INSIDE THE VEHICLE Always use floor mats designed to fit your vehicle. Only depress the accelerator, the brake, and the clutch use a floor mat that does not interfere with the opera- pedal (if present) to check for interference.
Page 160: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY PERIODIC SAFETY CHECKS YOU SHOULD MAKE OUTSIDE THE VEHICLE Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges.
Page 161: Starting And Operating
STARTING AND OPERATING STARTING THE ENGINE — GAS ENGINE AUTOMATIC TRANSMISSION NORMAL STARTING USING ENGINE START/STOP BUTTON Start the engine with the transmission in PARK position. Before starting your vehicle, adjust your seat, adjust Apply the brake before shifting into any driving range. To Turn On The Engine Using The ENGINE START/STOP both inside and outside mirrors, and fasten your seat Button...
Page 162 STARTING AND OPERATING AutoPark — Rotary Shifter and NOTE: off. The ignition will remain in the ACC mode until the gear selector is in PARK and the button is Eight-Speed Transmission Only For Keyless Enter-N-Go equipped vehicles, the engine pushed twice to the OFF mode. will turn off and the ignition switch will change to ACC AutoPark is a supplemental feature to assist in placing mode.
Page 163: Cold Weather Operation (Below -22°F Or −30°C)
STARTING AND OPERATING The starter motor will engage automatically, run for cranking with the accelerator pedal pushed all the way WARNING! 10 seconds, and then disengage. Once this occurs, to the floor. Release the accelerator pedal and the igni- release the accelerator pedal and the brake pedal, wait tion button/key once the engine is running smoothly.
Page 164: Automatic Transmission
STARTING AND OPERATING Normal Starting 3. If the gear selector is not in PARK and the ENGINE WARNING! START/STOP button is pushed once, the instrument USING THE ENGINE START/STOP BUTTON • cluster will display a “Vehicle Not In Park” message Never leave children alone in a vehicle, or with and the engine will remain running.
Page 165: Extreme Cold Weather
STARTING AND OPERATING • 4. Push the ENGINE START/STOP button a third time to If the engine stalls, or if the ignition switch is left ON CAUTION! return the ignition to the OFF position. for more than two minutes after the “Wait To Start” telltale goes out, reset the intake air heater by turn- Keyless Enter-N-Go Starting Procedure —...
Page 166: Normal Starting Procedure - Engine Manifold Air Temperature Above 66° F (19° C)
STARTING AND OPERATING NORMAL STARTING PROCEDURE — STARTING PROCEDURE — ENGINE CAUTION! ENGINE MANIFOLD AIR MANIFOLD AIR TEMPERATURE 0°F Do not crank the engine for more than 25 seconds at TEMPERATURE ABOVE 66° F TO 66°F (–18°C TO 19°C) a time or starter motor damage may result. Turn the ignition switch to the OFF position and wait at least (19°...
Page 167: Starting Procedure - Engine Manifold Air Temperature Below 0°F (-18°C)
STARTING AND OPERATING STARTING PROCEDURE — ENGINE 3. If the vehicle is driven and vehicle speed exceeds WARNING! 19 mph (31 km/h) before the intake air heater post- MANIFOLD AIR TEMPERATURE heat (after start) cycle is complete, the intake air intake piping, or turbocharger inlet in an attempt to BELOW 0°F (-18°C) heater will shut off.
Page 168: Normal Operation - Diesel Engine
STARTING AND OPERATING • NORMAL OPERATION — DIESEL ENGINE If climatized or diesel Number 1 ULSD fuel is not available, and you are operating below (20°F/-6°C), in sustained arctic conditions, Mopar® Premium Observe the following when the engine is operating: Diesel Fuel Treatment (or equivalent) is recom- •...
Page 169: Engine Idling
STARTING AND OPERATING Battery Blanket Usage NOTE: Your truck may have been ordered with an optional volt- age monitoring idle up feature. If a load is placed on the If ambient temperatures are low and the coolant tem- A battery loses 60% of its cranking power as the battery electrical system while the truck is in park, this feature perature is below 180°F (82°C), the engine idle speed temperature decreases to 0°F (-18°C).
Page 170: Noise
STARTING AND OPERATING 2. The engine RPM will go up to 1,100 RPM. To mal and will change from day to day, as the engine through a dosing module. This process will create a increase the RPM, push and hold the ACCEL/ breaks in, and can vary with changes in ambient tem- clicking sound and at times, will make noise even with RESUME switch and the idle speed will increase to...
Page 171: Idle Shutdown
STARTING AND OPERATING IDLE SHUTDOWN Usually the engine coolant (antifreeze) temperature CAUTION! indicated during operation will be to the left of center in This feature can be enabled so that the truck will auto- the normal range of the gauge. If oil pressure falls to less than normal readings, shut matically shutdown when the truck has been idling for a the engine off immediately.
Page 172: Engine Break-In Recommendations - Gas Engine
STARTING AND OPERATING NOTE: It includes a removable cap that is secured by a teth- CAUTION! ered strap. It also has a c-clip that is used for storage Light duty operation such as light trailer towing or no when not in use for the Winter months. During Winter load operation will extend the time before the engine is Never use Non-Detergent Oil or Straight Mineral Oil in months, remove the heater cord wiring assembly from...
Page 173: Diesel Exhaust Brake - Engine Braking (If Equipped)
STARTING AND OPERATING DIESEL EXHAUST BRAKE — ENGINE WARNING! • Never use the PARK position as a substitute for the BRAKING (IF EQUIPPED) parking brake. Always apply the parking brake fully when parked to guard against vehicle movement The purpose of the exhaust brake (engine braking) fea- and possible injury or damage.
Page 174: Automatic Transmission
STARTING AND OPERATING Automatic “Smart” Exhaust Brake Once the “Exhaust Brake Indicator” is illuminated and WARNING! the vehicle is moving faster than 5 mph (8 km/h); the Automatic “Smart” Exhaust Brake technology delivers exhaust brake will automatically operate when the complete stop before shifting to PARK, and verify smoother, less aggressive exhaust braking characteris- driver removes pressure from the accelerator pedal.
Page 175: Ignition Park Interlock
STARTING AND OPERATING NOTE: NOTE: WARNING! The transmission is NOT locked in PARK when the igni- In the event of a mismatch between the gear selector • Do not leave the key fob in or near the vehicle (or tion is in the ACC mode (even though the engine will be position and the actual transmission gear (for example, in a location accessible to children), and do not off).
Page 176 STARTING AND OPERATING NOTE: WARNING! On four-wheel drive vehicles be sure that the transfer case is in a drive position. hit someone or something. Only shift into gear when the engine is idling normally and your foot is When exiting the vehicle, always: firmly pressing the brake pedal.
Page 177 STARTING AND OPERATING Transmission Limp Home Mode CAUTION! CAUTION! Transmission function is monitored electronically for • Before moving the transmission gear selector out Towing the vehicle, coasting, or driving for any other abnormal conditions. If a condition is detected that of PARK, you must start the engine, and also press reason with the transmission in NEUTRAL can cause could result in transmission damage, Transmission...
Page 178 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recommend that you visit an authorized dealer at your earliest pos- sible convenience. An authorized dealer has diagnostic equipment to assess the condition of your transmission. If the transmission cannot be reset, authorized dealer service is required.
Page 179: Six-Speed Automatic Transmission - If Equipped
STARTING AND OPERATING NOTE: SIX-SPEED AUTOMATIC (ERS) Operation" in this section for further information. Some models will display both the selected gear limit, On four-wheel drive vehicles be sure that the transfer TRANSMISSION — IF EQUIPPED and the actual current gear, while in ERS mode. case is in a drive position.
Page 180 STARTING AND OPERATING • DRIVE (D) Release the gear selector and make sure it is fully WARNING! seated in the PARK gate. This range should be used for most city and highway • • When leaving the vehicle, always make sure the Look at the transmission gear position display and driving.
Page 181 STARTING AND OPERATING Transmission Limp Home Mode NOTE: If the transmission cannot be reset, authorized dealer service is required. Use caution when operating a heavily loaded vehicle at Transmission function is monitored electronically for low speeds (such as towing a trailer up a steep grade, Electronic Range Select (ERS) Operation abnormal conditions.
Page 182 STARTING AND OPERATING Overdrive Operation To exit ERS mode, simply push and hold the ERS (+) switch until the gear limit display disappears from the The automatic transmission includes an electronically instrument cluster. controlled Overdrive (fifth and sixth gears). The trans- mission will automatically shift into Overdrive if the fol- WARNING! lowing conditions are present:...
Page 183: Auxiliary Switches - If Equipped
For further information on using the auxiliary switches, is able to shift into and out of Overdrive. by the 4WD Control Switch (Transfer Case Switch), please refer to the Ram Body Builders Guide by access- which is located on the instrument panel. •...
Page 184 STARTING AND OPERATING This electronically shifted transfer case provides four The 4WD HIGH and 4WD LOW positions are designed WARNING! mode positions: for loose, slippery road surfaces only. Driving in the 4WD HIGH and 4WD LOW positions on dry hard sur- •...
Page 185 STARTING AND OPERATING NOTE: NOTE: Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping Before retrying a selection, make certain that all the The four-wheel drive system will not allow shifts speeds. Do not go faster than road conditions permit. necessary requirements for selecting a new transfer between 2WD/4WD HIGH if the front and/or rear case position have been met.
Page 186: Electronically Shifted Transfer Case (Six Speed Transmission) - If Equipped
STARTING AND OPERATING 4. After the desired position indicator light is on (not This electronically shifted transfer case provides four WARNING! flashing), shift the transmission back into gear. mode positions: • Two-Wheel Drive High Range (2WD) You or others could be injured or killed if you leave NOTE: •...
Page 187 STARTING AND OPERATING Transfer Case Position Indicator Lights the requirements for the selected position have WARNING! been met. To retry a shift: return the control switch The Transfer Case Position Indicator Lights (4WD and back to the original position, make certain all shift 4LOW) are located in the instrument cluster and indi- Always engage the parking brake when powering requirements have been met, wait five seconds and...
Page 188: Manually Shifted Transfer Case - If Equipped
STARTING AND OPERATING 2WD OR 4WD HIGH TO 4WD LOW NOTE: N (Neutral) N (Neutral) — This range disengages both the front and • If Steps 1 or 2 of either the Preferred or Alternate NOTE: rear driveshafts from the powertrain. To be used for flat Procedure are not satisfied prior to attempting the When shifting into or out of 4WD LOW some gear noise towing behind another vehicle.
Page 189 STARTING AND OPERATING Two-Wheel Drive High Range (2H) When operating your vehicle in 4L, the engine speed is shifts can be made up to 55 mph (88 km/h). With the approximately three times that of the 2H or 4H posi- vehicle in motion, the transfer case will engage/ Two-Wheel Drive High Range —...
Page 190: Air Suspension System - If Equipped
STARTING AND OPERATING • Normal Ride Height (NRH) – This is the standard posi- Do not attempt to shift into or out of 4WD LOW while WARNING! the transmission is in gear. tion of the suspension and is meant for normal driving. It will automatically adjust to maintain the rear ride The air suspension system uses a high pressure vol- Transfer Case Position Indicator Light...
Page 191: Instrument Cluster Display Messages
STARTING AND OPERATING NOTE: • INSTRUMENT CLUSTER DISPLAY Tire/Jack Mode – No indicator lamps will be illumi- nated. Tire/Jack Mode is disabled by driving the This mode is intended to be enabled with the engine MESSAGES vehicle, or by deselecting the mode via the running.
Page 192: Stabilizer/Sway Bar System
STARTING AND OPERATING NOTE: NOTE: Even when the axles are in the AXLE UNLOCK position, The rear axle must be locked before the front axle will the limited slip differential in the rear axle still provides lock. torque biasing capability for moderate low traction When both the axles are locked, to unlock the front environments.
Page 193: Safe Off-Road Driving
STARTING AND OPERATING SAFE OFF-ROAD DRIVING — POWER WARNING! WAGON ONLY road light. Once vehicle speed is reduced below 14 mph (22 km/h), the system will attempt to return to the Off-Road mode. OFF-ROAD DRIVING TIPS AND To disconnect the stabilizer/sway bar, shift to either VEHICLE CHARACTERISTICS 4WD HIGH or 4WD LOW and push the SWAY BAR button Your vehicle has excellent on and off-road capabilities.
Page 194: Driving In Snow, Mud And Sand
STARTING AND OPERATING The Basics Of Off-Road Driving When To Use Low Range and multiplied by 1,000 is the RTI. This vehicle has an RTI of 429 (connected sway bar) or an RTI of 538 (dis- You will encounter many types of terrain driving off- When driving off-road, shift into 4WD LOW for additional connected sway bar), which means you can articulate road.
Page 195: Crossing Obstacles (Rocks And Other High Points)
STARTING AND OPERATING Crossing Large Rocks Mud – Deep mud creates a great deal of suction • CROSSING OBSTACLES (ROCKS around the tires and is very difficult to get through. AND OTHER HIGH POINTS) When approaching large rocks, choose a path which You should use 4WD LOW with a gear low enough to ensures you drive over the largest with your tires.
Page 196: Hill Climbing
STARTING AND OPERATING HILL CLIMBING enough traction to complete the climb. If you do not WARNING! make it to the top, place the vehicle in REVERSE Hill climbing requires good judgment and a good under- and back straight down the grade using engine There is an increased risk of rollover when crossing standing of your abilities and your vehicle's limitations.
Page 197: Driving Through Water
STARTING AND OPERATING Driving Across An Incline – If at all possible avoid • DRIVING THROUGH WATER angle, current and bottom condition. Be careful of driving across an incline. If it is necessary, know murky or muddy waters, check for hidden obstacles. Extreme care should be taken crossing any type of your vehicle's abilities.
Page 198: Airing Down For Off-Road Driving
STARTING AND OPERATING depths greater than the vehicle's running ground mal air pressure before driving on road or at highway winch. If you are severely hung up on something you clearance. You should never attempt to cross flow- conditions. Be sure you have a way to return the tires to should jack the vehicle up and stack something under ing water which is deeper than the vehicle's running their normal on road air pressure.
Page 199: After Driving Off-Road
STARTING AND OPERATING Using The Tow Hooks With A Tow Strap – Tow • out cable. Placing something over the strung out WARNING! straps are a quick and easy way to recover your cable helps keep the cable on the ground if it vehicle from minor situations if you have a second- breaks.
Page 200: Limited-Slip Differential
STARTING AND OPERATING • Check for accumulations of plants or brush. These The limited-slip differential is especially helpful during very high forces and should be used with care. Do not things could be a fire hazard. They might hide dam- slippery driving conditions.
Page 201: Understanding The Features Of Your Winch
STARTING AND OPERATING Low Voltage Interrupt 3. Winch Drum With Integral Brake: The winch drum Gloves: It is extremely important to wear pro- allows the rope to be stored on the winch and trans- tective gloves while operating the winch or Your winch is equipped with a device that will interrupt mits force to the rope.
Page 202 STARTING AND OPERATING WARNING! WARNING! CAUTION! • • • Never use as a hoist. Always pass remote control through a window to Always inspect winch installation and synthetic avoid pinching lead in door, when using remote rope condition before operating the winch. Frayed, •...
Page 203 STARTING AND OPERATING Winch Rope Hook Strap Pulling Synthetic Rope 2. Put on gloves. 6. Secure to the anchor point. Once you have estab- WARNING! lished your anchor point, secure the tree-trunk pro- 3. Disengage the clutch to allow free spooling of the tector or choker-chain around the object.
Page 204 STARTING AND OPERATING CAUTION! Always be certain the anchor you select will withstand the load. NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural anchors include trees, stumps and rocks.
Page 205 STARTING AND OPERATING 12. Check synthetic rope. The rope should be neatly before the rope is put under tension. Do not wound around the spooling drum. Improper wind- approach or move the blanket once tension is ing can cause damage to the synthetic rope. applied.
Page 206: Rigging Techniques
STARTING AND OPERATING NOTE: stack, spool out that section of the rope and 19. Disconnect the remote control. Disconnect the reposition it to the opposite end of the drum, How to spool under no load: Arrange the remote remote control cord from the control box and store which will free up space for continued winching.
Page 207: Fuel Saver Technology - Gas Engine (If Equipped)
STARTING AND OPERATING ing pulling efficiency and damaging synthetic rope. A rope through a snatch block. Disengage the clutch and, snatch block, secured to a point directly in front of the using the snatch block, pull out enough synthetic rope vehicle will enable you to change your pulling direction to reach your anchor point.
Page 208: To Set A Desired Speed
STARTING AND OPERATING TO ACCELERATE FOR PASSING Metric Speed (km/h) WARNING! • Pushing the RES (+) button once will result in a Press the accelerator as you would normally. When the Leaving the Speed Control system on when not in use 1 km/h increase in set speed.
Page 209: To Deactivate
STARTING AND OPERATING • TO DEACTIVATE If the ACC sensor detects a vehicle ahead, ACC will WARNING! apply limited braking or accelerate (not to exceed A soft tap on the brake pedal, pushing the CANCEL but- the original set speed) automatically to maintain a •...
Page 210: Adaptive Cruise Control (Acc) Operation
STARTING AND OPERATING ADAPTIVE CRUISE CONTROL (ACC) ACTIVATING ADAPTIVE CRUISE TO ACTIVATE/DEACTIVATE OPERATION CONTROL (ACC) Push and release the Adaptive Cruise Control (ACC) on/off button. The ACC menu in the instrument cluster The speed control buttons (located on the right side of You can only engage ACC if the vehicle speed is above displays “ACC Ready.”...
Page 211: To Set A Desired Acc Speed
STARTING AND OPERATING TO CANCEL TO RESUME WARNING! The following conditions cancel the system: If there is a set speed in memory push the RES (+) but- Leaving the Adaptive Cruise Control (ACC) system on ton and then remove your foot from the accelerator •...
Page 212: To Vary The Speed Setting
STARTING AND OPERATING • TO VARY THE SPEED SETTING If the button is continually pushed, the set speed SETTING THE FOLLOWING will continue to decrease in 5 mph decrements until DISTANCE IN ACC To Increase Speed the button is released. The decrease in set speed is While ACC is set, you can increase the set speed by reflected in the instrument cluster display.
Page 213: Overtake Aid
STARTING AND OPERATING If there is no vehicle ahead, the vehicle will maintain ACC OPERATION AT STOP the set speed. If a slower moving vehicle is detected in If the ACC system brings your vehicle to a standstill the same lane, the instrument cluster displays the ACC while following a vehicle ahead, your vehicle will Set With Target Indicator Light, and the system adjusts resume motion, without any driver interaction, if the...
Page 214: Adaptive Cruise Control (Acc) Menu
STARTING AND OPERATING ADAPTIVE CRUISE CONTROL (ACC) DISPLAY WARNINGS AND To keep the ACC system operating properly, it is impor- tant to note the following maintenance items: MENU MAINTENANCE • Always keep the sensor clean. Carefully clear the The instrument cluster display will show the current ACC windshield.
Page 215: Precautions While Driving With Acc
STARTING AND OPERATING Offset Driving into the sun and fog on the inside of glass. In these PRECAUTIONS WHILE DRIVING cases, the instrument cluster display will show “ACC/ WITH ACC ACC may not detect a vehicle in the same lane that is FCW Limited Functionality Clean Front Windshield”...
Page 216 STARTING AND OPERATING Lane Changing ACC may not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it may not detect the vehicle until it's too late for the ACC system to take action.
Page 217: General Information
STARTING AND OPERATING GENERAL INFORMATION NORMAL (FIXED SPEED) CRUISE what speed was set. This light will turn on when the system is turned on via the on/off control. It turns CONTROL MODE The following regulatory statement applies to all Radio green when the cruise control is set.
Page 218: Parksense Rear Park Assist - If Equipped
STARTING AND OPERATING • The driver's preferred units can be selected through the The gear selector is removed from the DRIVE ParkSense can be active only when the gear selector is instrument panel settings. Refer to “Instrument Cluster position. in REVERSE. If ParkSense is enabled at this gear selec- Display”...
Page 219: Parksense Display
STARTING AND OPERATING PARKSENSE DISPLAY When the vehicle is in REVERSE, the warning display will turn on indicating the system status. The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on the object’s distance and location relative to the vehicle.
Page 220 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continu- ous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Continuous Tone WARNING ALERTS Rear Distance Greater than...
Page 221: Enabling And Disabling Parksense
STARTING AND OPERATING Adjustable Chime Volume Settings SERVICE THE PARKSENSE REAR PARKSENSE SYSTEM USAGE The rear chime volume settings are programmable PARK ASSIST SYSTEM PRECAUTIONS through the Uconnect system. Refer to “Uconnect Set- tings” in “Multimedia” for further information. During vehicle start up, when the Rear ParkSense Sys- NOTE: tem has detected a faulted condition, the instrument The chime volume settings include low, medium, and...
Page 222: Parksense Front And Rear Park Assist
STARTING AND OPERATING • On vehicles equipped with a tailgate, ParkSense PARKSENSE SENSORS CAUTION! should be disabled when the tailgate is in the low- The four ParkSense sensors, located in the rear fascia/ ered or open position and the vehicle is in •...
Page 223 STARTING AND OPERATING Front/Rear ParkSense Arcs 1 — No Tone/Solid Arc 6 — Fast Tone/Flashing Arc 2 — No Tone/Flashing Arc 7 — Fast Tone/Flashing Arc 3 — Fast Tone/Flashing Arc 8 — Slow Tone/Solid Arc 4 — Continuous Tone/Flashing Arc 9 —...
Page 224 STARTING AND OPERATING If an obstacle is detected in the left and/or right rear region, the display will show a single arc in the left and/or right rear region and the system will produce a tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from a single 1/2 second tone to slow, to fast, to continuous.
Page 225: Enabling And Disabling Front And/Or Rear Parksense
STARTING AND OPERATING NOTE: Front or Rear ParkSense switch is pushed, and the sys- CLEANING THE PARKSENSE tem requires service, the Front or Rear ParkSense ParkSense will reduce the volume of the radio, if on, SYSTEM switch LED will blink momentarily, and then the LED will when the system is sounding an audio tone.
Page 226: Lanesense - If Equipped
STARTING AND OPERATING • Use the ParkSense switch to turn the ParkSense The driver may manually override the haptic warning by CAUTION! system off if obstacles such as bicycle carriers, applying torque to the steering wheel at any time. trailer hitches, etc. are placed within 18 inches •...
Page 227: Lanesense Warning Message
STARTING AND OPERATING Lane Sense On Message System ON (Gray Lines) With White Telltale Lane Crossed (Flashing Yellow Lane Line) With Yellow Telltale Left Lane Departure — Only Left Lane Detected To turn the LaneSense system off, push the LaneSense NOTE: button again (LED turns on).
Page 228: Changing Lanesense Status
STARTING AND OPERATING NOTE: • When the LaneSense system senses the lane has been approached and is in a lane departure situa- • When enabled the system operates above 37 mph tion, the left lane line flashes yellow (on/off). The (60 km/h) and below 112 mph (180 km/h).
Page 229 STARTING AND OPERATING When the vehicle is shifted out of REVERSE (with Cam- AUX Camera Touchscreen Button The following table shows the approximate distances era delay turned on), the rear Camera image will be for each zone: displayed for up to 10 seconds after shifting to another gear, unless the vehicle speed exceeds 8 mph Zones Distance To The Rear Of...
Page 230: Aux Camera - If Equipped
STARTING AND OPERATING NOTE: The ParkView Camera is located in the center of the AUX CAMERA — IF EQUIPPED tailgate handle. • If the AUX button is pressed and no AUX Camera is Your vehicle may be equipped with one or two AUX Cam- NOTE: connected, the touchscreen will display a blue eras, which display rearview and side view images from...
Page 231 STARTING AND OPERATING Modes Of Operation NOTE: When the vehicle is shifted into REVERSE, the Rear View and Top View is the default view of the system The Rear View can be manually activated by selecting • Front tires will display on the image when the tires (Automatic Activation).
Page 232 STARTING AND OPERATING • screen to allow the driver to see both sides of the trailer While in Zoom View, the guidelines will not be Rear View Camera at the same time. This view allows the driver to pan visible. Pressing the Backup Camera soft key will left/right to better frame the trailer in the image.
Page 233 STARTING AND OPERATING Adjusting Centerline The camera delay system is turned off manually Zoom View is available until the gear selector is placed through the Uconnect Settings menu. Refer to in DRIVE or REVERSE and speeds are at or above Follow the steps below to manually adjust the “Uconnect Settings”...
Page 234: Aux Camera - If Equipped
STARTING AND OPERATING NOTE: • • The vehicle speed is over 8 mph (13 km/h) for Black video will be displayed for the right side of the 10 seconds Top and Rear View, and full screen of the Backup If the vehicle is in 4WD Low, the Forward Facing Cam- Camera view when the Rear View Camera is not era image will be displayed until the “X”...
Page 235: Engine Runaway - Diesel Engine
STARTING AND OPERATING NOTE: WARNING! WARNING! • If the AUX button is pressed and no AUX Camera is • The inlet for the engine air intake is located behind Never add fuel to the vehicle when the engine is connected, the touchscreen will display a blue the drivers side headlamp and receives air through running.
Page 236: Loose Fuel Filler Cap Message
STARTING AND OPERATING Emergency Fuel Can Refueling REFUELING THE VEHICLE — DIESEL WARNING! NOTE: ENGINE Static electricity can cause an ignition of flammable In the event that you run the vehicle out of fuel, once liquid, vapor or gas in any vehicle or trailer. To reduce refueled, place the ignition in the ON position for risk of serious injury or death when filling containers: 1.
Page 237: Diesel Exhaust Fluid
STARTING AND OPERATING NOTE: NOTE: The purpose of the SCR system is to reduce levels of NOx (oxides of nitrogen emitted from engines) that are Ensure funnel is inserted fully to hold flapper door • Your vehicle is equipped with a DEF injection sys- harmful to our health and the environment to a near- open.
Page 238 STARTING AND OPERATING Adding Diesel Exhaust Fluid ○ Excessive overfilling of the DEF tank can result in a MIL lamp/fault code and inaccurate level The DEF gauge (located on the instrument cluster) will readings. display the level of DEF remaining in the tank. Refer to “Instrument Cluster”...
Page 239: Vehicle Loading
STARTING AND OPERATING 3. Stop filling the DEF tank immediately when any of PAYLOAD CURB WEIGHT the following happen: DEF stops flowing from the fill The payload of a vehicle is defined as the allowable The curb weight of a vehicle is defined as the total bottle into the DEF tank, DEF splashes out the filler load weight a truck can carry, including the weight of weight of the vehicle with all fluids, including vehicle...
Page 240: Trailer Towing
STARTING AND OPERATING Gross Trailer Weight (GTW) CAUTION! WARNING! The GTW is the weight of the trailer plus the weight of Do not load your vehicle any heavier than the GVWR It is important that you do not exceed the maximum all cargo, consumables and equipment (permanent or or the maximum front and rear GAWR.
Page 241 STARTING AND OPERATING Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they are commonly used to tow small and medium sized trailers.
Page 242: Trailer Hitch Type And Maximum Trailer Weight
STARTING AND OPERATING Gooseneck Hitch 5. Install and adjust the tension in the weight distribut- 5. Install and adjust the tension in the weight distribut- ing bars per the manufacturers’ recommendations ing bars per the manufacturers’ recommendations The gooseneck hitch employs a pivoted coupling arm so that the height of the front fender is approxi- so that the height of the front fender is approxi- which attaches to a ball mounted in the bed of a pickup...
Page 243: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING NOTE: TRAILER TOWING WEIGHTS WARNING! Remember that everything put into or on the trailer (MAXIMUM TRAILER WEIGHT adds to the load on your vehicle. Also, additional Improper towing can lead to a collision. Follow these RATINGS) factory-installed options or dealer-installed options guidelines to make your trailer towing as safe as pos- must be considered as part of the total load on your sible:...
Page 244 STARTING AND OPERATING Towing Requirements — Trailer Brakes Integrated Trailer Brake Module — WARNING! If Equipped Do not interconnect the hydraulic brake system or • ○ GAWR vacuum system of your vehicle with that of the ○ Your vehicle may have an Integrated Trailer Brake Mod- Tongue weight rating for the trailer hitch utilized.
Page 245 STARTING AND OPERATING GAIN Adjustment Buttons (+/-) The user interface consists of the following: not recognized by the ITBM, braking functions will Manual Brake Control Lever not be available), the GAIN setting will illuminate Pushing these buttons will adjust the brake control and the correct type of trailer must be selected from power output to the trailer brakes in 0.5 increments.
Page 246 STARTING AND OPERATING NOTE: NOTE: Display Messages The trailer brake control interacts with the instrument • • An aftermarket controller may be available for use Disconnect the trailer wiring connector from the cluster display. Display messages, along with a single with trailers with air or electric-over-hydraulic trailer vehicle (or any other device plugged into vehicle’s chime, will be displayed when a malfunction is deter-...
Page 247: Towing Tips
STARTING AND OPERATING Air Suspension System NOTE: Using TOW/HAUL mode or selecting a lower gear range To aid in attaching/detaching the trailer from the (using the ERS shift control) while operating the vehicle vehicle, the air suspension system can be used. Refer under heavy loading conditions will improve perfor- to “Air Suspension System”...
Page 248: Before Plowing
STARTING AND OPERATING The loaded vehicle weight, including the snowplow sys- OPERATING TIPS CAUTION! tem, all aftermarket accessories, driver, passengers, Under ideal snow plowing conditions, 20 mph options, and cargo, must not exceed either the Gross The “Lamp Out” indicator could illuminate if exterior (32 km/h) should be maximum operating speed.
Page 249: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE Two-Wheel Drive Towing Condition Wheels OFF The Ground Four-Wheel Drive Models Models See Instructions • Automatic transmission in PARK NOT ALLOWED Flat Tow NONE • Transfer case in NEUTRAL (N) •...
Page 250: Recreational Towing - Four-Wheel Drive Models
STARTING AND OPERATING RECREATIONAL TOWING — 2. Shift the transmission to NEUTRAL. CAUTION! FOUR-WHEEL DRIVE MODELS NOTE: • Do not disconnect the rear driveshaft because If vehicle is equipped with air suspension, ensure fluid will leak from the transfer case, causing dam- NOTE: the vehicle is set to Normal Ride Height.
Page 251 STARTING AND OPERATING Shifting Out Of (N) NEUTRAL 10. Shift the transmission into PARK. On eight-speed 5. Turn the engine off. Shift automatic transmission transmissions the shifter will automatically select into PARK. On eight-speed transmissions the shifter Use the following procedure to prepare your vehicle for PARK when the engine is turned off.
Page 252: Driving Tips
STARTING AND OPERATING Flowing/Rising Water DRIVING TIPS CAUTION! • Always check the depth of the standing water WARNING! DRIVING ON SLIPPERY SURFACES before driving through it. Never drive through standing water that is deeper than the bottom of Do not drive on or across a road or path where water Acceleration the tire rims mounted on the vehicle.
Page 253: Off-Road Driving Tips
STARTING AND OPERATING • OFF-ROAD DRIVING TIPS After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake Care should be taken when attempting to climb steep rotors, wheels, brake linings, and axle yokes hills or driving diagonally across a hill or slope. If natu- inspected and cleaned as soon as possible.
Page 254: In Case Of Emergency
IN CASE OF EMERGENCY HAZARD WARNING FLASHERS ASSIST AND SOS SYSTEM — IF EQUIPPED The Hazard Warning Flashers switch is located on the NOTE: upper switch bank just below the radio. Depending on the vehicle’s trim level, the overhead console may vary. Hazard Warning Flashers Switch With 12-inch Display Push the switch to turn on the Hazard Warning Flash- ers.
Page 255 IN CASE OF EMERGENCY • The SOS and ASSIST buttons will only function if you 3. Once a connection between the vehicle and a SOS are connected to an operable LTE (voice/data) or 4G operator is made, the SOS Call system may transmit (data) network.
Page 256 IN CASE OF EMERGENCY cle’s SOS Call system will attempt to remain con- WARNING! WARNING! nected with the SOS operator until the SOS operator terminates the connection. • Modifications to any part of the SOS Call system detected. If the Air Bag Warning Light is illumi- could cause the air bag system to fail when you nated, have an authorized dealer service the Occu- 5.
Page 257: General Information
IN CASE OF EMERGENCY L'exploitation est autorisée aux deux conditions Exterior Bulbs WARNING! suivantes: Bulb Name Bulb Number and applications when it is safe to do so. Failure to do 1. l'appareil ne doit pas produire de brouillage, et so may result in an accident involving serious injury Low Beam (Halogen H11LL 2.
Page 258: Replacing Exterior Bulbs
IN CASE OF EMERGENCY Exterior Bulbs CAUTION! Bulb Name Bulb Number • Do not contaminate the bulb glass by touching it Center High Mounted with your fingers or by allowing it to contact other Stop Lamp (CHMSL) oily surfaces. Shortened bulb life will result. •...
Page 259 IN CASE OF EMERGENCY 3. Look under the hood and behind the headlamp to find the high beam bulb access cover. 4. Reach behind the headlamp and disengage the access cover by rotating counterclockwise. 5. Disconnect the internal lamp wiring harness connec- tor from the high beam bulb.
Page 260 IN CASE OF EMERGENCY Fog Lamps — If Equipped Rear Tail/Stop, Turn Signal And Backup Lamps Please see an authorized dealer for service on LED and Halogen front fog lamps. 1. Remove the two screws and push pins that pass Halogen through the bed sheet metal.
Page 261 IN CASE OF EMERGENCY Center High Mounted Stop Lamp CAUTION! (CHMSL) With Cargo Lamp Do not contaminate the bulb glass by touching it with 1. Remove the two screws holding the housing/lens to your fingers or by allowing it to contact other oily sur- the body as shown.
Page 262: Fuses
IN CASE OF EMERGENCY 2. Turn the socket a quarter turn counterclockwise to FUSES POWER DISTRIBUTION CENTER access the bulb. The Power Distribution Center is located in the engine 3. Pull the bulb straight out from the socket. compartment near the battery. This center contains WARNING! cartridge fuses, micro fuses, relays, and circuit break- 4.
Page 263 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – – Spare 60 Amp Yellow – ABS Pump Motor (HD Only) 60 Amp Yellow – Rad Fan – If Equipped 50 Amp Red – 400W Inverter – If Equipped 40 Amp Green –...
Page 264 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description — – Spare — – Spare 20 Amp Blue – Trailer Tow Backup Lights – If Equipped 20 Amp Blue – Trailer Tow Parking Lights – If Equipped 30 Amp Pink –...
Page 265 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 20 Amp Yellow Trailer Tow – Left Turn/Stop Lights - If Equipped – 20 Amp Yellow Non Memory Adjustable Pedals - If Equipped – – Spare – 10 Amp Red Fuel Vapor Blocker Valve - If Equipped –...
Page 266 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 15 Amp Blue Engine Control Module / Powertrain Control Module / AEB RACM MOD / Feed To AUX PDC Relay Coils/ HRLS – 15 Amp Blue ID / Clearance Lights –...
Page 267: Jacking And Tire Changing
IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description F103 – 10 Amp Red HeadLamp AFLS — If Equipped F104 – 20 Amp Yellow UCI Port / USB Rear REMOVAL OF JACK AND TOOLS WARNING! CAUTION! To access the jack and jack tools, you must remove the •...
Page 268 IN CASE OF EMERGENCY CAUTION! • The lug wrench can only be attached to extension two (2). • When attaching the tool to the winch mechanism be sure the large flared end opening on extension four (4) is positioned correctly over the winch mechanism adjusting nut.
Page 269: Removing The Spare Tire
IN CASE OF EMERGENCY WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 270: Preparations For Jacking
IN CASE OF EMERGENCY NOTE: PREPARATIONS FOR JACKING Passengers should not remain in the vehicle when the 1. Park the vehicle on a firm, level surface. Avoid ice or vehicle is being raised or lifted. slippery areas. JACKING INSTRUCTIONS WARNING! WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Page 271 IN CASE OF EMERGENCY 2. Using the lug wrench, loosen, but do not remove, the 3. Placement of the jack is critical: wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. Changing a dually tire requires the lug wrench adapter.
Page 272 IN CASE OF EMERGENCY 5. Remove the lug nuts and pull the wheel off. On Single Rear Wheel (SRW) trucks, install the spare wheel and lug nuts with the cone shaped end of the wheel nuts toward the wheel. On 3500 Dual Rear Wheel models (DRW) trucks, if the outer tire is being replaced then leave the inner wheel on the vehicle.
Page 273: To Stow The Flat Or Spare
IN CASE OF EMERGENCY 8. Lower the jack to its fully closed position. Stow the 3. Attach the lug wrench to the extension tubes with replaced tire, jack, and tools as previously the curved angle facing away from the vehicle. described.
Page 274: Reinstalling The Jack And Tools
IN CASE OF EMERGENCY REINSTALLING THE JACK AND HUB CAPS/WHEEL COVERS — TOOLS IF EQUIPPED The hub caps must be removed before raising the 1. Tighten the jack all the way down by turning the jack vehicle off the ground. turn-screw counterclockwise until the jack is snug.
Page 275: Jump Starting
IN CASE OF EMERGENCY NOTE: JUMP STARTING (wheel skins), insert the flat end of the lug wrench between the outer edge of the wheel cover and the • If you have a diesel engine, you may have two bat- wheel. Pry against the wheel to remove the wheel cover. If your vehicle has a discharged battery, it can be jump teries, however jump start off the driver side battery.
Page 276: Jump Starting Procedure
IN CASE OF EMERGENCY 5. Start the engine in the vehicle that has the booster WARNING! CAUTION! battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged • Take care to avoid the radiator cooling fan when- Failure to follow these procedures could result in battery.
Page 277: Gear Selector Override - 6-Speed
IN CASE OF EMERGENCY CAUTION! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular devices, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
Page 278: If Your Engine Overheats
IN CASE OF EMERGENCY To push or tow the vehicle in cases where the transmis- sion will not shift out of PARK (such as a depleted bat- tery), a Manual Park Release is available. Follow these steps to activate the Manual Park Release: 1.
Page 279: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY NOTE: • You can also turn the temperature control to maxi- CAUTION! mum heat, the mode control to floor and the blower • For trucks equipped with an 8–speed transmission, control to high. This allows the heater core to act as •...
Page 280: Two-Wheel Drive Models
IN CASE OF EMERGENCY Wheels OFF The Towing Condition 2WD Models 4WD Models Ground See instructions in “Recreational Towing” under “Starting And If transmission is operable: Operating” • Transmission in NEUTRAL Automatic Transmission in PARK • Flat Tow NONE • 30 mph (48 km/h) max speed •...
Page 281: Four-Wheel Drive Models
IN CASE OF EMERGENCY FOUR-WHEEL DRIVE MODELS EMERGENCY TOW HOOKS — CAUTION! IF EQUIPPED The manufacturer recommends towing with all wheels Tow hooks are for emergency use only, to rescue a OFF the ground. Acceptable methods are to tow the Your vehicle may be equipped with emergency tow vehicle stranded off road.
Page 282: Servicing And Maintenance
SERVICING AND MAINTENANCE NOTE: • SCHEDULED SERVICING — GAS ENGINE Check the fluid levels of the coolant reservoir, brake master cylinder, power steering and automatic Under no circumstances should oil change intervals transmission (six-speed only) and fill as needed exceed 8,000 miles (13,000 km), 12 months or Your vehicle is equipped with an automatic oil change •...
Page 283 SERVICING AND MAINTENANCE At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Inspect engine cooling system protection and hoses. • Inspect exhaust system. • Inspect engine air cleaner if using in dusty or off-road conditions. If required, replace air cleaner filter. •...
Page 284: Heavy Duty Use Of The Vehicle
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Maintenance Replace cabin air filter. Replace engine air cleaner filter. Replace spark plugs. ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 285: Scheduled Servicing- Diesel Engine
SERVICING AND MAINTENANCE Replace the engine oil and oil filter every 15,000 miles • SCHEDULED SERVICING— DIESEL ENGINE Inspect front end, and lubricate — If equipped with (24,000 km) or 12 months, or sooner if prompted by serviceable fittings. the oil change indicator system. Under no circum- •...
Page 286: Perform Service Indicator - Cummins® Diesel
SERVICING AND MAINTENANCE PERFORM SERVICE INDICATOR — vice”. When the “Perform Service” message is dis- case Ventilation (CCV) filter element. The procedure for played on the instrument cluster it is necessary to have clearing and resetting the “Perform Service” indicator CUMMINS®...
Page 287 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Inspect engine air cleaner filter, replace if necessary. ** Inspect the CV/Universal joints. Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;...
Page 288 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Inspect the front and rear axle sur- faces. If gear oil leakage is suspected, check the fluid level. If using your vehicle for police, taxi, fleet, off-road or frequent trailer towing change the axle fluid.
Page 289 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Change automatic transmission fluid and filter(s) if using your vehicle for any of the following: police, fleet, or frequent trailer towing (68RFE trans- mission only). Change automatic transmission fluid and filter(s).
Page 290: Engine Compartment
SERVICING AND MAINTENANCE ENGINE COMPARTMENT 6.4L ENGINE 1 — Engine Coolant Pressure Cap 6 — Battery 2 — Engine Coolant Reservoir 7 — Air Cleaner Filter 3 — Engine Oil Fill 8 — Power Steering Fluid Reservoir Cap 4 — Engine Oil Dipstick 9 —...
Page 291: 6.7L Diesel Engine - Six-Speed 68Rfe
SERVICING AND MAINTENANCE 6.7L DIESEL ENGINE — SIX-SPEED 68RFE 1 — Battery 7 — Brake Fluid Reservoir Cap 2 — Engine Coolant Pressure Reservoir 8 — Battery 3 — Engine Coolant Reservoir Cap 9 — Air Cleaner Filter 4 — Automatic Transmission Dipstick 10 —...
Page 292: L Diesel Engine - Six-Speed Aisin (As69Rc Hd)
SERVICING AND MAINTENANCE 6.7L DIESEL ENGINE — SIX-SPEED AISIN (AS69RC HD) 1 — Battery 7 — Brake Fluid Reservoir Cap 2 — Engine Coolant Reservoir Cap 8 — Battery 3 — Engine Coolant Pressure Reservoir 9 — Power Distribution Center (Fuses) 4 —...
Page 293: Checking Oil Level - Gas Engine
SERVICING AND MAINTENANCE CHECKING OIL LEVEL — GAS ADDING WASHER FLUID ENGINE The fluid reservoir is located under the hood and should be checked for fluid level at regular intervals. Fill To ensure proper lubrication of your vehicle's engine, the reservoir with windshield washer solvent only (not the engine oil must be maintained at the correct level.
Page 294: Pressure Washing
SERVICING AND MAINTENANCE PRESSURE WASHING ENGINE OIL WARNING! Change Engine Oil — Gas Engine • Battery fluid is a corrosive acid solution and can CAUTION! burn or even blind you. Do not allow battery fluid to The oil change indicator system will remind you that it is contact your eyes, skin, or clothing.
Page 295 SERVICING AND MAINTENANCE American Petroleum Institute (API) vehicle is unused for an extended period of time, incor- Lubricants which do not have both the engine oil certifi- rect oil, extended oil changes or extended idling. If the Engine Oil Identification Symbol — cation mark and the correct SAE viscosity grade num- engine continues to tick or if the Malfunction Indicator ber should not be used.
Page 296: Engine Oil Filter
SERVICING AND MAINTENANCE Engine Air Cleaner Filter Selection Engine oil not designated by the FCA or Cummins® ENGINE OIL FILTER Material Standards and API CK-4 should not be used, The quality of replacement engine air cleaner filters The engine oil filter should be replaced with a new filter as engine and exhaust system durability may be com- varies considerably.
Page 297 SERVICING AND MAINTENANCE Engine Air Cleaner Filter Inspection and 2. Lift the air cleaner cover to access the air cleaner filter. Replacement — Diesel Engine 3. Remove the air cleaner filter element from the hous- Inspect engine air cleaner filter for dirt and or debris, if ing assembly.
Page 298: Air Conditioner Maintenance
SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling — AIR CONDITIONER MAINTENANCE WARNING! R-134a — (If Equipped) For best possible performance, your air conditioner Do not remove the cabin air filter while the vehicle is should be checked and serviced by an authorized R-134a Air Conditioning Refrigerant is a hydrofluoro- running, or while the ignition is in the ACC or ON/RUN dealer at the start of each warm season.
Page 299 SERVICING AND MAINTENANCE 3. There are travel stops on both sides of the glove compartment. Push inward on right side of the glove compartment travel stop to disengage the stop. Then pull the right of the glove compartment out- ward (away from the hinge) to disengaging the right side of the compartment from the hinge.
Page 300: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE Conditions that would require replacement: WARNING! • Rib chunking (one or more ribs has separated from • When working near the radiator cooling fan, dis- belt body) connect the fan motor lead. The fan is temperature • Rib or belt wear controlled and can start at any time regardless of •...
Page 301: Engine Mounted Fuel Filter Replacement - Diesel Engine
SERVICING AND MAINTENANCE NOTE: If more than a couple ounces/milliliters of fuel have CAUTION! been drained, follow the directions for “Priming If The Care should be taken in disposing of used fluids from Engine Has Run Out Of Fuel.” your vehicle. Used fluids, indiscriminately discarded, •...
Page 302: Underbody Mounted Fuel Filter Replacement - Diesel Engine
SERVICING AND MAINTENANCE 11. Install lid onto housing and tighten to 22.5 ft lb CAUTION! CAUTION! (30.5 N.m). Do not overtighten the lid. • • Diesel fuel will damage blacktop paving surfaces. Diesel fuel will damage blacktop paving surfaces. 12. Prime the engine using the procedure in “Priming Drain the filter into an appropriate container.
Page 303: Priming If The Engine Has Run Out Of Fuel - Diesel Engine
SERVICING AND MAINTENANCE PRIMING IF THE ENGINE HAS RUN INTERVENTION REGENERATION WARNING! OUT OF FUEL — DIESEL ENGINE STRATEGY — MESSAGE PROCESS Do not use alcohol or gasoline as a fuel blending FLOW agent. They can be unstable under certain conditions WARNING! and be hazardous or explosive when mixed with die- The Cummins®...
Page 304: Diesel Exhaust Fluid
Avoid using the wiper blades to remove frost or ice from States by calling 866-RAM-INFO (866-726-4636). In the windshield. Keep the blade rubber out of contact Canada call 1–800–465–2001 (English) or 1–800–...
Page 305 SERVICING AND MAINTENANCE 3. Tilt the lower end of the wiper blade away from the arm and use one finger to push the release tab toward the wiper arm. Windshield Wiper Arm And Blade Removing Wiper From Wiper Arm 1 — Wiper 1 —...
Page 306: Exhaust System
SERVICING AND MAINTENANCE EXHAUST SYSTEM To minimize the possibility of catalytic converter CAUTION! damage: The best protection against carbon monoxide entry into • • Do not interrupt the ignition when the transmission The catalytic converter requires the use of the vehicle body is a properly maintained engine is in gear and the vehicle is in motion.
Page 307 SERVICING AND MAINTENANCE Engine Coolant Checks NOTE: prevent reducing this extended maintenance period, it is important that you use the same engine coolant (OAT Check the engine coolant (antifreeze) protection every • Mixing of engine coolant (antifreeze) other than coolant conforming to MS.90032) throughout the life of 12 months (before the onset of freezing weather, where specified Organic Additive Technology (OAT) engine your vehicle.
Page 308: Charge Air Cooler - Inter-Cooler
SERVICING AND MAINTENANCE • • Mixing engine coolant (antifreeze) types is not rec- coolant in open containers or allow it to remain in Check the coolant freeze point in the radiator and in ommended and can result in cooling system dam- puddles on the ground.
Page 309: Brake System
SERVICING AND MAINTENANCE engine. The air entering the engine has been cooled by If necessary, add fluid to bring level within the desig- WARNING! about 50° to 100°F (10° to 38°C). This cooling pro- nated marks on the side of the reservoir of the brake cess enables more efficient burning of fuel resulting in master cylinder.
Page 310 SERVICING AND MAINTENANCE Fluid Level Check — Six-Speed its performance may be impaired by supplemental addi- dipstick. Note that the holes in the dipstick will be tives. Therefore, do not add any fluid additives to the Transmission full of fluid if the actual level is at or above the hole. transmission.
Page 311: Rear Axle And 4X4 Front Driving Axle Fluid Level
SERVICING AND MAINTENANCE 8. Reinsert the dipstick until fully seated and lock it Insert the wire into the fill plug hole and use it like a down. The bending of the blade will orient the cap in dipstick. Remove the wire and measure from the the correct position.
Page 312: Transfer Case
SERVICING AND MAINTENANCE TRANSFER CASE the air cleaner for tightness. The air filter element must also be clean and serviced according to the instructions Selection Of Lubricant outlined in the Scheduled Maintenance section of this manual. Use only the manufacturer's recommended fluid. Refer Tampering With Noise Control System to “Fluids And Lubricants”...
Page 313 SERVICING AND MAINTENANCE Noise Emission Warranty This warranty covers this vehicle as designed, built and the time it left the manufacturer's control, caused noise equipped by the manufacturer, and is not limited to any emissions to exceed Federal standards, are covered by The manufacturer warrants that this vehicle as manu- particular part, component or system of the vehicle this warranty for the life of the vehicle.
Page 314: Hoisting
SERVICING AND MAINTENANCE Tire Markings NOTE: HOISTING • P (Passenger) — Metric tire sizing is based on US design standards. P-Metric tires have the letter “P” A conventional floor jack may be used at the jacking molded into the sidewall preceding the size designa- locations.
Page 315 SERVICING AND MAINTENANCE TIRE SIZING CHART EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in)
Page 316 SERVICING AND MAINTENANCE Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Page 317 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure Tire And Loading Information Placard NOTE: Under a maximum loaded vehicle condition, gross axle NOTE: weight ratings (GAWRs) for the front and rear axles The proper cold tire inflation pressure is listed on the must not be exceeded.
Page 318 SERVICING AND MAINTENANCE Metric Example For Load Limit (4) The resulting figure equals the For example, if “XXX” amount equals 635 kg and there available amount of cargo and luggage will be five 68 kg passengers in your vehicle, the load capacity.
Page 319 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 320: Tires - General Information
SERVICING AND MAINTENANCE TIRES — GENERAL INFORMATION Both underinflation and overinflation affect the stability CAUTION! of the vehicle and can produce a feeling of sluggish Tire Pressure response or over responsiveness in the steering. After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.
Page 321 SERVICING AND MAINTENANCE very important. Increased tire pressure and reduced Damaged Run Flat tires, or Run Flat tires that have Refer to “Freeing A Stuck Vehicle” in “In Case Of Emer- vehicle loading may be required for high-speed vehicle experienced a loss of pressure should be replaced gency”...
Page 322 SERVICING AND MAINTENANCE NOTE: These indicators are molded into the bottom of the WARNING! tread grooves. They will appear as bands when the Wheel valve stem must be replaced as well when tread depth becomes a 1/16 of an inch (1.6 mm). installing new tires due to wear and tear in existing •...
Page 323: Tire Types
SERVICING AND MAINTENANCE Snow Tires Spare Tire Matching Original Equipped TIRE TYPES Tire And Wheel — If Equipped Some areas of the country require the use of snow tires All Season Tires — If Equipped during the Winter. Snow tires can be identified by a Your vehicle may be equipped with a spare tire and “mountain/snowflake”...
Page 324: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE WARNING! WARNING! WARNING! tread wear indicators, the temporary use spare tire Compact and Collapsible spares are for temporary Limited use spares are for emergency use only. Instal- needs to be replaced. Be sure to follow the warnings, emergency use only.
Page 325: Tire Chains And Traction Devices
SERVICING AND MAINTENANCE Dark Vapor Chrome, Black Satin Chrome, or Low Gloss 3500 (Single Rear Wheel) Models CAUTION! Clear Coat Wheels • Install on rear tires only. • Avoid products or automatic car washes that use For LT275/70R18E and LT285/60R20E tires, use CAUTION! acidic solutions or strong alkaline additives or harsh of a U-class snow chain is recommended.
Page 326: Tire Rotation Recommendations
SERVICING AND MAINTENANCE NOTE: CAUTION! If your vehicle is equipped with a Tire Pressure Informa- • Drive cautiously and avoid severe turns and large tion System (TPIS): bumps, especially with a loaded vehicle. • The Tire Pressure Information System (TPIS) uses •...
Page 327: Department Of Transportation Uniform
SERVICING AND MAINTENANCE the government course as a tire graded TEMPERATURE GRADES CAUTION! 100. The relative performance of tires The Temperature grades are A (the inward. That way the tread design of asymmetrical depends upon the actual conditions of tires and the white writing of the OWL tires will highest), B, and C, representing the maintain proper position.
Page 328: Storing The Vehicle
SERVICING AND MAINTENANCE BODYWORK BODY AND UNDERBODY WARNING! MAINTENANCE The temperature grade for this tire is PROTECTION FROM ATMOSPHERIC Cleaning Headlights established for a tire that is properly AGENTS Your vehicle is equipped with plastic headlights and fog inflated and not overloaded. Exces- Vehicle body care requirements vary according to geo- lights that are lighter and less susceptible to stone sive speed, under-inflation, or exces-...
Page 329 SERVICING AND MAINTENANCE • • Use a high quality cleaner wax, such as Mopar® If a lot of driving is done on gravel roads, consider CAUTION! Cleaner Wax to remove road film, stains and to pro- mud or stone shields behind each wheel. tect your paint finish.
Page 330: Interiors
SERVICING AND MAINTENANCE Stain Repel Fabric Cleaning Procedure — WARNING! WARNING! If Equipped Do not use silicon-based protection products to clean A frayed or torn belt could rip apart in a collision and Stain Repel seats may be cleaned in the following your bedliner.
Page 331: Leather Parts
SERVICING AND MAINTENANCE LEATHER PARTS GLASS SURFACES Mopar® Total Clean is specifically recommended for All glass surfaces should be cleaned on a regular basis leather upholstery. with Mopar® Glass Cleaner, or any commercial household-type glass cleaner. Never use an abrasive Your leather upholstery can be best preserved by regu- type cleaner.
Page 332: Technical Specifications
TECHNICAL SPECIFICATIONS IDENTIFICATION DATA BRAKE SYSTEM WHEEL AND TIRE TORQUE SPECIFICATIONS If power assist is lost for any reason (for example, VEHICLE IDENTIFICATION NUMBER repeated brake applications with the engine off), the brakes will still function. However, you will experience a Proper lug nut/bolt torque is very important to ensure The Vehicle Identification Number (VIN) is found on the substantial increase in braking effort to stop the...
Page 333: Fuel Requirements - Gas Engine
TECHNICAL SPECIFICATIONS After 25 miles (40 km), check the lug nut/bolt torque to This engine is designed to meet all emis- be sure that all the lug nuts/bolts are properly seated sions regulations and provide satisfactory against the wheel. fuel economy and performance when using high quality unleaded gasoline having a posted octane number range of 87 as specified by the (R+M)/2 method.
Page 334: Gasoline/Oxygenate Blends
TECHNICAL SPECIFICATIONS Designated TOP TIER Detergent Gasoline DO NOT USE E-85 IN NON-FLEX some vehicles. The manufacturer recommends that contains a higher level of detergents to fur- gasoline without MMT be used in your vehicle. The FUEL VEHICLES ther aide in minimizing engine and fuel sys- MMT content of gasoline may not be indicated on the tem deposits.
Page 335: Carbon Monoxide Warnings
TECHNICAL SPECIFICATIONS NOTE: For most year-round service, No. 2 diesel fuel meeting FUEL SPECIFICATIONS ASTM (formerly known as the American Society for Test- Intentional tampering with the emissions control system The Cummins® Turbo Diesel engine has been devel- ing and Materials) specification D-975 Grade S15 will can result in civil penalties being assessed against you.
Page 336: Biodiesel Fuel Requirements
20% (B20) provided months. that you comply with the requirements outlined below. Ram PickUp 2500/3500 Only — 15,000 Miles* It is important that you understand and comply with Fuel Water Separation — Must Use (*unless otherwise notified with a oil service message) these requirements.
Page 337: Fluid Capacities - Gas Engine
TECHNICAL SPECIFICATIONS FLUID CAPACITIES — GAS ENGINE Metric Fuel (Approximate) 2500/3500 Shortbed Models 31 Gallons 117 Liters 2500/3500 Longbed Models 32 Gallons 121 Liters 2500/3500 Crew Cab Longbed Models — If Equipped 50 Gallons 189 Liters Engine Oil With Filter 6.4L Engine (We recommend you use SAE 0W-40 engine oil meeting the requirements of FCA Material 7 Quarts 6.6 Liters...
Page 338: Fluids And Lubricants
TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS GASOLINE ENGINE Component Fluid, Lubricant, or Genuine Part We recommend you use Mopar® Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Engine Coolant Technology). For best performance and maximum protection under all types of operating conditions, the manufacturer only recom- mends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SN.
Page 339: Chassis
Transfer Case We recommend you use Mopar® Transfer Case Lubricant for Borg Warner 44-44 and 44-45. We recommend you use SAE 75W-85 HD Ram GL-5 Synthetic Axle Lubricant in 9.25 Front, 11.5 and 12.0 (Single Rear Front and Rear Axle Wheel) Rear Axles.
Page 340: Chassis
Transfer Case We recommend you use Mopar® BW44–44 Transfer Case Fluid. We recommend you use SAE 75W-85 HD Ram GL-5 Synthetic Axle Lubricant in 9.25 Front, 11.5 and 12.0 (Single Rear Front and Rear Axle Fluid (2500/3500) Wheel) Rear Axles. Use Mopar® GL-5 Synthetic Gear Lubricant SAE 75W-140 in 12.0 (Dual Rear Wheel) Rear axles. Lim- ited slip additive is required for limited slip axles.
Page 341: Multimedia
MULTIMEDIA ○ UCONNECT SYSTEMS Only connect and use trusted media devices (e.g. WARNING! personal mobile phones, USBs, CDs). • Privacy of any wireless and wired communications can- For detailed information about your Uconnect 4/4C/4C It is not possible to know or to predict all of the not be assured.
Page 342: Uconnect 3 Settings
MULTIMEDIA UCONNECT 3 SETTINGS Voice, Clock, Safety & Driving Assistance, Lights, Doors & Locks, Power Side Steps (if equipped), Auto-On Com- fort Systems (if equipped), Engine Off Options, Suspen- sion, Trailer Brake, Audio, Phone/Bluetooth®, Radio Setup (if equipped), Restore Settings, and Clear Per- sonal Data.
Page 343 MULTIMEDIA Language After pressing the Language button on the touchscreen, the following setting will be available: Setting Name Selectable Options English Français Español Set Language Arabic/Brasileiro/Deutsch/English Español/Français/Italiano/Nederlands Polski/Português/Türk/Pусский NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Español) for all display nomenclature, including the trip functions and the Navigation system (if equipped).
Page 344 MULTIMEDIA Units After pressing Units on the touchscreen, the following settings will be available: Setting Name Selectable Options Units Metric Custom Speed km/h Distance Fuel Consumption MPG (UG) MPG (UK) L/100 km km/L Pressure Power — If Equipped HP (US) HP (UK) Temperature °C...
Page 345 MULTIMEDIA Clock After pressing the Clock button on the touchscreen, the following settings will be available: Setting Name Selectable Options 12 hour 24 hour Set Time & Format Sync Time Safety/Assistance After pressing the Safety/Assistance button on the touchscreen, the following settings will be available: Setting Name Selectable Options Forward Collision Warning —...
Page 346 MULTIMEDIA Setting Name Selectable Options Surround View Camera Delay — If Equipped NOTE: The “Surround View Camera Delay” setting determines whether or not the screen will display the 360 degree view image with guidelines for up to 10 seconds after the vehicle is shifted out of REVERSE.
Page 347 MULTIMEDIA Setting Name Selectable Options NOTE: When the vehicle is shifted out of REVERSE (with camera delay turned OFF), the rear camera mode is exited and the navigation or audio screen appears again. When the vehicle is shifted out of REVERSE (with camera delay turned ON), the rear view image with dynamic grid lines will be displayed for up to 10 seconds after shifting out of REVERSE unless the forward vehicle speed exceeds 8 mph (12 km/h), the transmission is shifted into PARK or the ignition is switched to the OFF position.
Page 348 MULTIMEDIA Setting Name Selectable Options Tire Fill Assist Setting Name Selectable Options Forward Collision Warning — If Equipped Warning Only Warning & Braking Forward Collision Warning Sensitivity — Near If Equipped Front ParkSense Chime Volume High Rear ParkSense Chime Volume — High If Equipped Tilt Side Mirrors In Reverse —...
Page 349 MULTIMEDIA Setting Name Selectable Options NOTE: When the vehicle is shifted out of REVERSE (with camera delay turned Off), the rear camera mode is exited and the navigation or audio screen appears again. When the vehicle is shifted out of REVERSE (with camera delay turned On), the rear view image with dynamic grid lines will be displayed for up to 10 seconds after shifting out of REVERSE unless the forward vehicle speed exceeds 8 mph (12 km/h), the transmission is shifted into PARK or the ignition is switched to the OFF position.
Page 350 MULTIMEDIA Setting Name Selectable Options Tire Fill Assist Lights After pressing the Lights button on the touchscreen, the following settings will be available: Setting Name Selectable Options 0 sec 30 sec Headlight Off Delay 60 sec 90 sec 0 sec 30 sec Headlight Illumination On Approach 60 sec...
Page 351 MULTIMEDIA Setting Name Selectable Options NOTE: When the “Rear Cargo Guidance Lights” feature is selected, the lights in the cargo and bed of the truck will come on either when the headlight switch is pressed, or the button on the back bed of the truck is pressed. Doors &...
Page 352 MULTIMEDIA Setting Name Selectable Options Passive Entry — If Equipped NOTE: The “Passive Entry” feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. It automatically unlocks the doors when the outside door handle is grabbed.
Page 353 MULTIMEDIA Engine Off Options After pressing the Engine Off Options button on the touchscreen, the following settings will be available: Setting Name Selectable Options Easy Exit Seats — If Equipped 0 sec 30 sec Headlight Off Delay 60 sec 90 sec 0 sec 45 sec Engine Off Power Delay...
Page 354 MULTIMEDIA Setting Name Selectable Options Wheel Alignment Mode NOTE: The “Wheel Alignment Mode” feature prevents auto leveling of the air suspension while performing a wheel alignment service. Before performing a wheel alignment, this mode must be enabled. Refer to an authorized dealer for further information. Trailer Brake —...
Page 355 MULTIMEDIA Setting Name Selectable Options Speed Adjusted Volume NOTE: The “Speed Adjusted Volume” feature increases or decreases volume relative to vehicle speed. Surround Sound — If Equipped NOTE: The “Surround Sound” feature provides simulated surround sound mode. AUX Volume Offset — If Equipped NOTE: The “AUX Volume Offset”...
Page 356 MULTIMEDIA SiriusXM® Setup — If Equipped After pressing the SiriusXM® Setup button on the touchscreen, the following settings will be available: Setting Name Selectable Options Tune Start Channel Skip List of Channels NOTE: SiriusXM® can be programmed to exclude undesirable channels while scanning. To make your selection, press the Channel Skip button on the touchscreen, select the chan- nels you would like to skip.
Page 357: Uconnect 4/4C/4C Nav Settings
MULTIMEDIA Clear Personal Data After pressing the Clear Personal Data button on the touchscreen, the following setting will be available: Setting Name Selectable Options Clear Personal Data NOTE: When this feature is selected it will remove all personal data including Bluetooth® devices and presets. If “Yes” is selected a pop-up will appear asking "Are you sure you want to clear all personal data?”...
Page 358 MULTIMEDIA Language After pressing the Language button on the touchscreen, the following setting will be available: Setting Name Selectable Options Set Language English Français Español NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Español) for all display nomenclature, including the trip functions and the Navigation system (if equipped).
Page 359 MULTIMEDIA Setting Name Selectable Options Fuel Saver Display in Cluster — If Equipped NOTE: When selected, the system displays fuel saver mode in the instrument cluster. Navigation Next Turn Pop-ups Displayed In Cluster — If Equipped Phone Pop-ups Displayed in Cluster — If Equipped Units After pressing the Units button on the touchscreen, you may select each unit of measurement independently displayed in the Instrument Cluster Display, and Navigation system (if equipped).
Page 360 MULTIMEDIA Voice After pressing the Voice button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Never w/Help Always Clock After pressing the Clock button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With GPS —...
Page 361 MULTIMEDIA Setting Name Selectable Options Surround View Camera Delay — If Equipped NOTE: The “Surround View Camera Delay” setting determines whether or not the screen will display the 360 degree view image with guidelines for up to 10 seconds after the vehicle is shifted out of REVERSE.
Page 362 MULTIMEDIA Safety & Driving Assistance After pressing the Safety & Driving Assistance button on the touchscreen, the following settings will be available: Setting Name Selectable Options Surround View Camera — If Equipped NOTE: The “Surround View Camera” feature displays a complete 360 degree view of the vehicle's exterior environment while backing up. Surround View Camera Delay —...
Page 363 MULTIMEDIA Setting Name Selectable Options Active ParkView Backup Camera Guidelines NOTE: The “Active ParkView Backup Camera Guidelines” feature overlays the Rear Backup Camera image with active or dynamic grid lines to help illustrate the width of the vehicle and its projected backup path, based on the steering wheel position when the option is checked. A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.
Page 364 MULTIMEDIA Setting Name Selectable Options Blind Spot Alert — If Equipped Lights Lights & Chime Hill Start Assist — If Equipped Tire Fill Assist — If Equipped Mirrors & Wipers After pressing the Mirrors & Wipers button on the touchscreen, the following settings will be available: Setting Name Selectable Options Tilt Side Mirrors In Reverse —...
Page 365 MULTIMEDIA Setting Name Selectable Options Headlight Illumination On Approach – NOTE: When the “Headlight Illumination On Approach” feature is selected, the headlights will activate and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked with the key fob.
Page 366 MULTIMEDIA Doors & Locks After pressing the Doors & Locks button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto Door Locks — If Equipped NOTE: When the “Auto Door Locks” feature is selected, all doors lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit”...
Page 367 MULTIMEDIA Setting Name Selectable Options Personal Settings Linked To Key Fob — If Equipped NOTE: • The “Personal Settings Linked To Key Fob” feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. • The seats return to the memorized seat location (if “Personal Settings Linked To Key Fob”...
Page 368 MULTIMEDIA Engine Off Options After pressing the Engine Off Options button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off Power Delay – NOTE: When the “Engine Off Power Delay” feature is selected, the power window switches, radio, Uconnect phone system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to OFF.
Page 369 MULTIMEDIA Setting Name Selectable Options Transport Mode NOTE: When the “Transport Mode” feature is selected, the air suspension system lowers and then disables to assist with flat bed towing. Wheel Alignment Mode NOTE: Before performing a wheel alignment, the “Wheel Alignment Mode” must be enabled. Refer to an authorized dealer for further information. Trailer —...
Page 370 MULTIMEDIA Setting Name Selectable Options Trailer Name List of Trailer Names NOTE: You can select and personalize your trailer name depending on the type of trailer you are hauling. Select the trailer name from the following list: trailer, boat, car, cargo, dump, equipment, flatbed, gooseneck, horse, livestock, motorcycle, snowmobile, travel, utility, and 5th wheel.
Page 371 MULTIMEDIA Setting Name Selectable Options Surround Sound — If Equipped NOTE: The “Surround Sound” feature provides simulated surround sound mode. AUX Volume Offset — If Equipped NOTE: The “AUX Volume Offset” feature provides the ability to tune the audio level for portable devices connected through the AUX input. Auto Play Phone/Bluetooth®...
Page 372 MULTIMEDIA SiriusXM® Setup — If Equipped After pressing the SiriusXM® Setup button on the touchscreen, the following settings will be available: Setting Name Selectable Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the 12 presets, so you can enjoy the complete song.
Page 373 MULTIMEDIA Restore Default Settings After pressing the Restore Default Settings button on the touchscreen, the following setting will be available: Setting Name Selectable Options Restore Default Settings Cancel NOTE: When the “Restore Settings” feature is selected, it resets clock, audio and other features to their default settings. Clear Personal Data After pressing the Clear Personal Data button on the touchscreen, the following setting will be available: Setting Name...
Page 374: Uconnect 4C Nav With 12-Inch Display Settings
MULTIMEDIA UCONNECT 4C NAV WITH 12-INCH Press the Settings button on the touchscreen to display the settings menu screen. In this mode, the Uconnect DISPLAY SETTINGS system allows you to access programmable features that may be equipped such as Language, Display, Units (if equipped), Voice Settings, Clock, Camera, Safety &...
Page 375 MULTIMEDIA Language After pressing the Language button on the touchscreen, the following setting will be available: Setting Name Selectable Options Language English Español Français NOTE: When the Language feature is selected, you may select one of multiple languages (English / Français / Español) for all display nomenclature, including the trip functions and the Navigation system (if equipped).
Page 376 MULTIMEDIA Setting Name Selectable Options Controls Screen Timeout — If Equipped Fuel Saver Display — If Equipped NOTE: When selected, the system displays fuel saver mode in the instrument cluster. Navigation Turn-by-Turn Displayed in Cluster — If Equipped Phone Pop-ups Displays In Cluster Ready To Drive Pop-Ups —...
Page 377 MULTIMEDIA Voice Settings After pressing the Voice Settings button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Never w/Help Always Clock After pressing the Clock button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With GPS —...
Page 378 MULTIMEDIA Setting Name Selectable Options Surround View Camera Guidelines — If Equipped NOTE: The “Surround View Camera Guidelines” feature allows you to see active guidelines over the Surround View Camera display whenever the gear selector is put into REVERSE, or the Surround View button on the touchscreen is pressed.
Page 379 MULTIMEDIA Setting Name Selectable Options CHMSL (Center High Mounted Stop Lamp) Camera Dynamic Centerline — If Equipped NOTE: When the “CHMSL Camera Dynamic Centerline” feature is selected, it will assist in backing up for trailer alignment and hook up. This feature is only available if your vehicle is equipped with Surround View Camera.
Page 380 MULTIMEDIA Mirrors & Wipers After pressing the Mirror & Wipers button on the touchscreen, the following settings will be available: Setting Name Selectable Options Tilt Side Mirrors In Reverse — If Equipped NOTE: When the “Tilt Side Mirrors In Reverse” feature is selected, the outside side-view mirrors will tilt downward when the ignition is in the ON/RUN position and the transmission gear selector is in the REVERSE position.
Page 381 MULTIMEDIA Setting Name Selectable Options NOTE: When the “Headlights With Wipers” feature is selected, and the headlight switch is in the AUTO position, the headlights turn on approximately 10 seconds after the wipers are turned on. The headlights also turn off when the wipers are turned off if they were turned on by this feature. Auto Dim High Beams —...
Page 382 MULTIMEDIA Auto-On Comfort & Remote Start — If Equipped After pressing the Auto-On Comfort & Remote Start button on the touchscreen, the following setting will be available: Setting Name Selectable Options Auto-On Driver Heated/Vented Seat & Remote Start All Starts Steering Wheel —...
Page 383 MULTIMEDIA Setting Name Selectable Options NOTE: • When “1st Press Of Key Fob Unlocks: Driver Door” is programmed, only the driver's door unlocks on the first press of the key fob unlock button. You must push the key fob unlock button twice to unlock the passengers’ doors. •...
Page 384 MULTIMEDIA Setting Name Selectable Options Easy Exit Seat — If Equipped NOTE: When the “Easy Exit Seat” feature is selected, the Driver’s seat will automatically move rearward once the engine is shut off. Suspension — If Equipped After pressing the Suspension button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Suspension Messages...
Page 385 MULTIMEDIA Trailer Brake After pressing the Trailer Brake button on the touchscreen, the following setting will be available: Setting Name Selectable Options Trailer Trailer 1 Trailer 2 Trailer 3 Trailer 4 After selecting the specific trailer, the following programmable options become available: Setting Name Selectable Options Use This Trailer...
Page 386 MULTIMEDIA Audio Settings After pressing the Audio Settings button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Front Right Back Left NOTE: The “Balance/Fade” feature allows you to adjust the Balance and Fade settings. Press and drag the Speaker icon or use the arrows to adjust, tap the C icon to readjust to the center.
Page 387 MULTIMEDIA Bluetooth® After pressing the Bluetooth® button on the touchscreen, the following settings will be available: Setting Name Selectable Options Phone Pop-ups Displayed in Cluster Do Not Disturb List of Settings NOTE: Press “Do Not Disturb” to access the available settings. The following settings are: “Auto Reply” (Both, Text, Call), “Auto Reply Message” (Custom, Default), and “Custom Auto Reply Message”...
Page 388 MULTIMEDIA Setting Name Selectable Options Listener Items Listening History List Of Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the 12 presets, so you can enjoy the complete song.
Page 389: Safety And General Information
MULTIMEDIA Setting Name Selectable Options Clear Personal Data Cancel NOTE: When the “Clear Personal Data” feature is selected it removes all personal data including Bluetooth® devices and presets. Setting Name Selectable Options Clear SiriusXM® Data Done NOTE: You must contact SiriusXM® Customer Care at 1-855-290-6593 in order to remove your account and profile information associated with SiriusXM® in this vehicle. •...
Page 390: Uconnect 3 With 5-Inch Display
MULTIMEDIA Care And Maintenance 1 — RADIO 10 — MEDIA Push the RADIO button on the faceplate to enter Radio Pushing the MEDIA button on the faceplate will allow Touchscreen Mode. The different tuner modes, FM/AM/SXM you to switch to Media mode: CD (if equipped), USB, •...
Page 391 MULTIMEDIA SiriusXM® Satellite Radio Mode — The radio is equipped with the following modes: During a Seek Up function, if the radio reaches the starting station after passing through the entire band If Equipped • two times, the radio will stop at the station where it •...
Page 392: Media Mode
MULTIMEDIA ○ Equalizer — Press the Equalizer button on the This functionality is only available for radios equipped 5. To set the time, select the Seek Up or Seek Down with a Satellite receiver. To receive satellite radio, the touchscreen to adjust the Bass, Mid and Treble. arrows as appropriate.
Page 393 MULTIMEDIA Audio Source Selection USB/iPod® Mode Fast Seek Down Press and hold the Seek Down button on the touch- Once in Media Mode, press the Source button on the USB/iPod® Mode is entered by either inserting a USB screen and the desired mode will begin to rewind touchscreen and the desired mode button on the touch- Jump Drive or iPod®...
Page 394: Phone Mode
MULTIMEDIA NOTE: PHONE MODE The Uconnect Phone allows you to dial a phone number with your mobile phone using simple voice commands. For mobile phone compatibility and pairing instructions, Operating Phone Mode please visit UconnectPhone.com. NOTE: AUX Mode The Uconnect Phone requires a mobile phone equipped with the Bluetooth®...
Page 395 MULTIMEDIA Connecting/Disconnecting A Mobile 5. If “No” is selected and you still would like to pair a 9. When the pairing process has successfully com- Phone Or Bluetooth® Device pleted, the system will prompt you to choose whether or not this is your favorite phone. Selecting PAIRING A PHONE the “Yes”...
Page 396 MULTIMEDIA Deletion Of A Mobile Phone Or A Downloading A Phonebook From Your NOTE: Bluetooth® Audio Device Mobile Phone The names in the phonebook which do not contain phone numbers or where both fields (name and sur- To delete a mobile phone or Bluetooth® audio device If equipped and specifically supported by your phone, name) are empty will not be displayed.
Page 397 MULTIMEDIA Answering Or Ignoring A Call With No Call Currently In • • Only the mobile phone’s phonebook is downloaded. Calls without a reply Progress SIM card phonebook is not part of the mobile • All calls phonebook. When an incoming call rings or is announced on the To access these types of calls, press the Recent Calls Uconnect system, push the Answer button on the touch- •...
Page 398: Steering Wheel Audio Controls
MULTIMEDIA Transferring/Call Continuation READING MESSAGES Transferring The system can read the messages received by the mobile phone. The ongoing calls can be transferred from the mobile phone to the system and vice versa without ending the To use this function, the mobile phone must support call.
Page 399: Media Mode
MULTIMEDIA MEDIA MODE Pushing the top of the switch once will go to the next track on the selected media (AUX/USB/Bluetooth®). Pushing the bottom of the switch once goes to the beginning of the current track, or to the beginning of the previous track if it is within eight seconds after the current track begins to play.
Page 400: Radio Operation And Mobile Phones
MULTIMEDIA Applicable to only Uconnect 4C/4C NAV With 8.4-inch from repositioning the mobile phone, it is recom- Display, and Uconnect 4C NAV With 12-inch Display mended that the volume be turned down or off during radios, different scenarios are listed when a non-phone mobile phone operation when not using the Uconnect device is plugged into the smaller and larger USB Ports, system.
Page 401: Voice Recognition Quick Tips
MULTIMEDIA 2. This device must accept any interference received, harmful interference to radio communications. How- 2. Reduce background noise. Wind noise and passen- including interference that may cause undesired ever, there is no guarantee that interference will not ger conversations are examples of noise that may operation.
Page 402: Basic Voice Commands
MULTIMEDIA BASIC VOICE COMMANDS The following basic Voice Commands can be given at any point while using your Uconnect system. Push the VR button on the steering wheel. After the beep, say: • “ Cancel” to stop a current voice session “...
Page 403: Radio
MULTIMEDIA RADIO 1. Once an incoming text message is read to you, push Press the Browse button on the touchscreen to see all the VR button on the steering wheel or Phone Use your voice to quickly get to the AM, FM or button (if enabled).
Page 404: Climate (4C/4C Nav)
MULTIMEDIA NOTE: SIRI® EYES FREE — IF EQUIPPED Voice Text Reply is not compatible with iPhone®, but if • Only the beginning of your custom message will be Siri lets you use your voice to send text messages, your vehicle is equipped with Siri® Eyes Free, you can seen on the touchscreen.
Page 405: Apple Carplay® - If Equipped
MULTIMEDIA • • Text Messages Additional Apps La operación de este equipo está sujeta a las siguientes dos condiciones: • Additional Apps Refer to your Uconnect Owner’s Manual Supplement for further information. Refer to your Uconnect Owner’s Manual Supplement for 1.
Page 406 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE IF YOU NEED ASSISTANCE FCA US LLC CUSTOMER CENTER P.O. Box 21–8004 FOR YOUR VEHICLE The manufacturer and its authorized dealers are vitally Auburn Hills, MI 48321–8004 interested in your satisfaction. We want you to be happy Phone: (866) 726-4636 with our products and services.
Page 407 CUSTOMER ASSISTANCE MOPAR PARTS CUSTOMER ASSISTANCE FOR THE service contract. We are not responsible for other com- panies’ contracts. If you purchased a contract other HEARING OR SPEECH IMPAIRED than a genuine FCA Canada Inc. service contract and Mopar original equipment parts & accessories and fac- (TDD/TTY) you have a problem, you will have to contact the admin- tory filled fluids are available from an authorized dealer.
Page 408 CUSTOMER ASSISTANCE To contact NHTSA, you may call the PUBLICATION ORDER FORMS Vehicle Safety Hotline toll free at To order the following manuals, you may use either the 1-888-327-4236 (TTY: website or the phone numbers listed below. 1-800-424-9153); or go to Service Manuals http://www.safercar.gov;...
Page 409 INDEX Alarm Panic ..... .14 Adaptive Cruise Control (ACC) (Cruise Control) . . .207 Back-Up .....226 Security Alarm .
Page 410 INDEX Caps, Filler Disposal Of Used Coolant ...306 Draining Fuel/Water Separator Filter ..298 Oil (Engine) ....288, 293 Drain, Flush, And Refill .
Page 411 INDEX Idling .....167 Fluid Level Checks Gauges Jump Starting ....273 Brake .
Page 412 INDEX Hood Release ....58 Keyless Enter-N-Go ... .23, 159, 162 Hill Descent Control Indicator ..115 Hub Caps .
Page 413 INDEX Malfunction Indicator Light (Check Engine) . .104, 110 Oil Change Indicator ....283 Pickup Box ....72, 74 Manual Oil, Engine .
Page 414 INDEX Rear ParkSense System ...216, 220 Safety Tips ....156 Sentry Key (Immobilizer) ....20 Rear Window, Sliding .
Page 415 INDEX Steering High Speed ....318 Trailer And Tongue Weight ...241 Tilt Column ....33 Inflation Pressure .
Page 416 INDEX Reset Auto-Up ....56 Windshield Defroster ....157 Vehicle Identification Number (VIN) ..330 Windshield Washers .
Page 419 It is always the driver’s responsibility to comply with all local laws. This Owner’s Manual has been prepared to help you get acquainted with your new Ram brand vehicle and to provide a convenient reference for common questions.
Page 420 ©2023 FCA US LLC. All Rights Reserved. Tous droits réservés. Ram is a registered trademark of FCA US LLC. Ram est une marque déposée de FCA US LLC. App Store is a registered trademark of Apple Inc. Google Play Store is a registered trademark of Google.

This manual is also suitable for:

3500 2020

RAM 2500 2020 Owner's Manual

Quick Links

Related Manuals for RAM 2500 2020

Summary of Contents for RAM 2500 2020