Page 1 RAM TRUCK 2 0 1 1 1 5 0 0 / 2 5 0 0 / 3 5 0 0 O W N E R ’ S M A N U A L...
Page 2: Introduction
TABLE OF CONTENTS SECTION ............3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 4: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 5: Introduction
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
Page 6 INTRODUCTION 5...
Page 7: Van Conversions/Campers
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 8: Vehicle Identification Number
VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
Page 10: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Wireless Ignition Node (WIN) — If Equipped ......12 Key FOB .
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Open Window Feature — If Equipped ......23 Using The Panic Alarm .
Page 12 Seat Belt Pretensioners — If Equipped ..51 Enhanced Seat Belt Use Reminder System (BeltAlert ) ......51 Seat Belts And Pregnant Women .
Page 13: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Key Fob with Remote Keyless Entry (RKE) — If Equipped Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch.
Page 14: Key Fob
Wireless Ignition Node (WIN) 1 — OFF 2 — ACC (ACCESSORY) 3 — ON/RUN 4 — START THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob.
Page 15: Removing Key Fob From Ignition
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand. Emergency Key Removal NOTE: You can insert the double-sided emergency key into the lock cylinder with either side up.
Page 16: Key-In-Ignition Reminder
(EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
Page 17: Sentry Key
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY The Sentry Key Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
Page 18: Replacement Keys
All of the Key Fobs provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only Key Fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle.
Page 19: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 20: To Disarm The System
NOTE: If the Vehicle Security Light stays on continu- ously during vehicle operation, have the system checked by an authorized dealer. To Disarm the System Use the RKE transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the Vehicle Security Light will flash for 30 seconds.
Page 21: Remote Keyless Entry (Rke) - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The front courtesy overhead console and door cour- tesy lights do not turn off if the dimmer control is in the interior lights ON position (extreme right posi- tion). • The illuminated entry system will not operate if the dimmer control is in the extreme left position.
Page 22 within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE transmitter.
Page 23: To Lock The Doors
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lamps with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: •...
Page 24: Remote Open Window Feature - If
Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: •...
Page 25: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using the Panic Alarm To turn the Panic Alarm feature ON or OFF, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.
Page 26: General Information
1. With the RKE transmitter buttons facing down, use a flat blade screwdriver to pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal. 2. Remove and replace the battery. Avoid touching the new battery with your fingers.
Page 27: How To Use Remote Start
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE maintaining security. The system has a range of approxi- mately 300 ft (91 m). NOTE: The vehicle must be equipped with an auto- matic transmission to be equipped with Remote Start. How To Use Remote Start All of the following conditions must be met before the engine will remote start: •...
Page 28 Remote Start Abort Message on Electronic Vehicle Information Center (EVIC) — If Equipped The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prema- turely: • Remote Start Aborted - Door Ajar •...
Page 29 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shut downs, the system will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote Start request. To Exit Remote Start Mode and Drive the Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm System...
Page 30: Door Locks
DOOR LOCKS Manual Door Locks Front and rear doors may be locked by moving the lock knob down or unlocked by moving the lock knob up. Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed.
Page 31: Power Door Locks - If Equipped
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks — If Equipped A power door LOCK switch is on each front door trim panel. Use this switch to lock or unlock the doors. Power Door Lock Switch Location 1 - Unlock 2 - Lock If you press the power door LOCK switch while the Key...
Page 32 Auto Lock Doors Programming The Auto Lock Doors feature can be enabled or disabled as follows: • For vehicles equipped with the EVIC, refer to “Elec- tronic Vehicle Information Center (EVIC)/Personal Settings (System Setup)” in “Understanding Your In- strument Panel” for further information. •...
Page 33 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle has been shifted into the PARK position after the vehicle has been driven (shifted out of PARK and all doors closed). Auto Unlock Doors Programming — If Equipped The Auto Unlock Doors feature can be enabled or dis- abled as follows: •...
Page 34: Child-Protection Door Lock
Child-Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the Child-Protection Door Lock system. Child-Protection Door Lock Location THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to engage and disengage the Child-Protection locks.
Page 35: Windows
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged. NOTE: • After setting the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
Page 36 The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab , Mega Cab and Crew Cab models.
Page 37 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly. To open the window part way, press to the first detent and release it when you want the window to stop. Auto-Up Feature with Anti-Pinch Protection (4-Door Models Driver’s and Front Passenger Door Only) —...
Page 38 Auto-Up Reset It may be necessary at some point in time to reactivate the Auto-up/Auto-down feature. To do so, perform the following steps: 1. Pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed.
Page 39: Wind Buffeting
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or in partially open positions. This is a normal occurrence and can be minimized.
Page 40 infant and child restraint systems. For more information on LATCH, see Lower Anchors and Tether for CHildren (LATCH). NOTE: The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision.
Page 41: Lap/Shoulder Belts
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the Quad Cab , Mega Cab and Crew Cab front center seating position have combi- nation lap/shoulder belts.
Page 42 WARNING! (Continued) • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing your belt in the wrong place could make your injuries in an accident much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
Page 43 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle WARNING! • A belt buckled into the wrong buckle will not protect you properly.
Page 44 WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in an accident, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones.
Page 45 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in an accident. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug.
Page 46 Regular Cab Front Center Three Point Belt 1. The front center seat belt on the Regular Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat.
Page 47 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in an accident.
Page 48: Lap/Shoulder Belt Untwisting Procedure
In Use Position Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 49: Adjustable Upper Shoulder Belt Anchorage
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Squeeze the anchorage button located on the upper belt guide to release the anchorage, and then move it up or down to the position that fits you best.
Page 50: Energy Management Feature
WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones.
Page 51: Seat Belts In Passenger Seating Positions
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE this feature. Children 12 years old and under should always be properly restrained in the rear seat. How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2.
Page 52: Seat Belt Pretensioners - If Equipped
If the passenger seating position is equipped with an ALR and is being used for normal usage: Only pull the belt webbing out far enough to comfortably wrap around the occupants mid-section so as to not activate the ALR. If the ALR is activated you will hear a ratcheting sound as the belt retracts.
Page 53 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). BeltAlert can be enabled or disabled by your authorized dealer or by performing the following procedure: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the...
Page 54: Seat Belts And Pregnant Women
Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen.
Page 55: Supplemental Restraint System (Srs) - Airbags
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) – Airbags This vehicle has Advanced Front Airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air- bag is mounted in the center of the steering wheel.
Page 56: Airbag System Components
The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Airbags based upon seat position.
Page 57: Advanced Front Airbag Features
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Side Airbag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat Track Position Sensors Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver and front passenger airbags.
Page 58 WARNING! (Continued) • Do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags may offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure.
Page 59 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes side impact sensors adjacent to both front and rear seat occupants that are calibrated to deploy the SABIC airbags during impacts that require airbag occupant protection. WARNING! • If your vehicle is equipped with left and right Supplemental Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC.
Page 60 Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: Children 12 years old and under should always ride buckled up in a rear seat. WARNING! Infants in rear-facing child restraints should never ride in the front seat of a vehicle with a passenger Advanced Front Airbag.
Page 61 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not lean against the door or window. If your vehicle has side airbags, and deployment occurs, the side airbags will inflate forcefully into the space between you and the door. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
Page 62: Airbag Deployment Sensors And Controls
Airbag Deployment Sensors and Controls Occupant Restraint Controller (ORC) The ORC is part of a Federally regulated safety system required for this vehicle. The ORC determines if deployment of the front and/or side airbags in a frontal or side collision is required. Based on the impact sensors signals, a central electronic ORC deploys the Advanced Front Airbags, SABIC air- bags —...
Page 63 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat belts are necessary for your protection in all acci- dents, and also are needed to help keep you in position, away from an inflating airbag. The ORC monitors the readiness of the electronic parts of the airbag system whenever the ignition switch is in the START or ON/RUN position.
Page 64 Driver and Passenger Advanced Front Airbag Inflator Units The Driver and Passenger Advanced Front Airbag Infla- tor Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the Advanced Front Airbags, it signals the inflator units.
Page 65 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE inflates. This especially applies to children. The side curtain airbag is only about 3-1/2 in (9 cm) thick when it is inflated. Because airbag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an airbag should have deployed.
Page 66 If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor.
Page 67 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you.
Page 68: Event Data Recorder (Edr)
Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. The Airbag Warning Light monitors the internal circuits and interconnecting wiring associated with airbag system electrical components. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer ser- vice the airbag system immediately.
Page 69: Child Restraints
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record such data as: • How various systems in your vehicle were operating; •...
Page 70 Children 12 years and under should ride properly buck- led up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. WARNING! In an collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle.
Page 71 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE by children who weigh more than 20 lbs (9 kg) but are less than one year old. Both types of child restraints are held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
Page 72 NOTE: For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK. Cana- dian residents, should refer to Transport Canada’s web- site for additional information. http://www.tc.gc.ca/ roadsafety/safedrivers/childsafety/index.htm WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision.
Page 73 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
Page 74 WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower...
Page 75 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraints having tether straps and hooks for connection to the seat back tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
Page 76 Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH mechanisms in the center position of a Quad Cab rear seat, or Crew Cab model with a bench rear seat. A child may be placed in the rear center seating position of a Quad Cab , or Crew Cab bench model using the seat belt and child tether anchorage.
Page 77 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 78 each behind the front center and right seats. Quad Cab , Mega Cab and Crew Cab models have three anchor- ages, one behind each of the rear seats. WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 79 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. Regular Cab Tether Strap Mounting 1 — Tether Strap Hook 2 — Tether Strap to Child Restraint 3 —...
Page 80 Head Restraint Adjustment 2. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and then to the anchor directly behind the center rear seat. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 3.
Page 81 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufactur- er’s instructions. Multiple Child Restraint Quad Cab /Mega Cab 1 — Inner Anchor Strap 4 —...
Page 82: Engine Break-In Recommendations
2. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint, through the outboard tether strap loop, then route it to the tether strap loop located directly behind the center rear seat.
Page 83: Safety Tips
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.
Page 84: Exhaust Gas
Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
Page 85: Safety Checks You Should Make Inside The Vehicle
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision.
Page 86 WARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and inter- fering with the pedals or the ability to control the...
Page 87: Periodic Safety Checks You Should Make Outside The Vehicle
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks.
Page 88: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......93 Inside Day/Night Mirror ....93 Automatic Dimming Mirror —...
Page 89 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped ... . 103 Ventilated Seats — If Equipped ..106 Manual Seat Adjuster —...
Page 90 Daytime Running Lights (DRL) (Canada Only And Fleet Vehicles) ....127 Multifunction Lever ....127 Windshield Wipers And Washers .
Page 91 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parksense System Usage Precautions ..144 Parkview Rear Back Up Camera — If Equipped ......147 Turning Parkview On Or Off —...
Page 92 Sunroof Maintenance ....160 Sunroof Fully Closed ....160 Electrical Power Outlets .
Page 93 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Window Features ....176 Rear Window Defroster ....176 Power Sliding Rear Window —...
Page 94: Mirrors
MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle). Adjusting Rearview Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield).
Page 95: Automatic Dimming Mirror - If Equipped
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated.
Page 96: Outside Mirrors Folding Feature
WARNING! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror.
Page 97: Power Mirrors - If Equipped
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. Power Mirror Controls The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. Power Mirror Controls 1 —...
Page 98: Heated Mirrors - If Equipped
To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Power Mirror Movement UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Heated Mirrors —...
Page 99: Illuminated Vanity Mirror - If Equipped
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirror — If Equipped Illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on auto- matically.
Page 100: Trailer Towing Mirrors - If Equipped
Slide-On-Rod Extender Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped in or out).
Page 101: Uconnect™ Phone - If Equipped
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A small blindspot mirror is located next to main mirror and can be adjusted separately. Blindspot Mirror Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a hands-free system that allows you to use voice commands to dial a phone number stored in your mobile phone.
Page 102: Power Seats - If Equipped
WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 103 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch.
Page 104: Power Lumbar - If Equipped
CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 105 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater.
Page 106 Press the switch once to select HIGH- level heating. Press the switch a sec- ond time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF. NOTE: • Once a heat setting is selected, heat will be felt within two to five minutes.
Page 107: Ventilated Seats - If Equipped
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF. Press the switch once to select HIGH- level heating.
Page 108: Manual Seat Adjuster - If Equipped
Press the switch once to choose HIGH, press it a second time to choose LOW. Pressing the switch a third time will turn the ventilated seat OFF. When HIGH speed is selected both lights on the switch will be illuminated. When LOW speed is selected one light will be illuminated.
Page 109: Manual Reclining Seats - If Equipped
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE While sitting in the seat, pull up on the handle and slide the seat forward or backward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
Page 110: 40-20-40 Front Bench Seat - If Equipped
position, release the handle. To return the seatback, lift upward on the handle, lean forward and release the handle at the desired position. WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
Page 111: Mega Cab Rear Seat Features
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mega Cab Rear Seat Features Reclining Rear Seats — If Equipped The recliner handle is located on the outside of the seat cushion. To adjust the seatback, lift upward on the handle, lean back on the seatback and when you reach the desired position, release the handle.
Page 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Table Mode Handle Table Mode 2. Fold the seatback forward. 3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. Folding Rear Seat — If Equipped Both the outboard rear seats will drop and move forward when the seatback is folded flat.
Page 113 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 114: Head Restraints
2. Fold the seatback down and push the seat forward. Rear Passenger Fold Flat Seats 3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 WARNING! An improperly latched seat could cause serious in- jury or death.
Page 115 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.
Page 116 Rear Head Restraints The two outboard seat are equipped with adjustable head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the adjustment button, located on the base of the head restraint, and push downward on the head restraint.
Page 117: Driver Memory Seat - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED Driver memory seats allow the driver to recall settings for the adjustable pedals, mirrors, seats and the radio presets using the key fob. The memory seat buttons are located on the outboard side of the drivers seat cushion.
Page 118: Setting Memory Positions And Linking Rke
Setting Memory Positions and Linking RKE Transmitter to Memory NOTE: Each time the S (SET) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store new settings. 1. Turn the vehicle key to the ON/RUN position. 2.
Page 119: Memory Position Recall
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memory Position Recall NOTE: • The vehicle must be in PARK to recall the memory positions. • Not all motors may be moved at one time. Refer to the “Seats/Eight-Way Power Seat” in this section for fur- ther information.
Page 120: Self-Limiting Control
To disable another RKE transmitter linked to either memory position, repeat Steps 1-3 for each RKE trans- mitter. NOTE: The capability to link RKE transmitters to memory is enabled when delivered from the factory. The capability to link RKE transmitters to memory can be disabled (or later re-enabled) by an authorized dealer.
Page 121: To Open And Close The Hood
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE feature may be automatically disabled if the seat is positioned rearward enough and there is no benefit in moving the seat any farther rearward. NOTE: The Easy Entry/Easy Exit feature can be en- abled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC).
Page 122 2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood. Safety Latch (1500 Series Shown) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 CAUTION! To prevent possible damage, do not slam the hood to close it.
Page 123: Lights
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped).
Page 124: Headlights
Headlights To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position.
Page 125: Headlight Delay
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The engine must be running before the head- lights will turn on in the Automatic Mode. Headlight Delay To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately 90 seconds.
Page 126: Interior Lights
Fog Light Switch The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the...
Page 127: Cargo Light
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The brightness of the instrument panel lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the headlights are on you can supplement the brightness of the odometer, trip odom- eter, radio and overhead console by rotating the control to the right until you hear a click.
Page 128: Lights-On Reminder
Lights-on Reminder If the headlights, parking lights, or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights.
Page 129 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Turn Signal Lever NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
Page 130: Windshield Wipers And Washers
High/Low Beam Switch Push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. High/Low Beam Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WINDSHIELD WIPERS AND WASHERS Windshield Wipers...
Page 131: Windshield Washers
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
Page 132: Mist Feature
WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Page 133: Heated Steering Wheel - If Equipped
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle.
Page 134: Driver Adjustable Pedals - If Equipped
WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion, or other physical conditions must exer- cise care when using the steering wheel heater. It may cause burns even at low temperatures, espe- cially if used for long periods.
Page 135: Adjustment
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustment 1. Position the driver’s seat so that you are at least 10 in (25.4 cm) away from the airbag, located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3.
Page 136: Electronic Speed Control - If Equipped
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever is located on the right side of the steering wheel. Electronic Speed Control Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: In order to ensure proper operation, the Elec- tronic Speed Control System has been designed to shut...
Page 137: To Set A Desired Speed
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the Electronic Speed Control system off when you are not using it.
Page 138: To Accelerate For Passing
To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released.
Page 139: Parksense Rear Park Assist - If Equipped
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE REAR PARK ASSIST — IF EQUIPPED The ParkSense Rear Park Assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.g. during a parking maneuver.
Page 140: Parksense Display
The ParkSense Warning Display is located in the Instru- ment cluster’s EVIC display. It provides both visual and audible warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Rear ParkSense Display UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 ParkSense Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status.
Page 141 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Park Assist System Off Slow Tone The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Fast Tone Continuous Tone...
Page 143 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Rear Distance Greater than (in/cm)
Page 144: Enabling And Disabling Park Sense
Enabling and Disabling Park Sense ParkSense can be enabled and disabled with a switch located in the switch bank of the instrument panel or through the Customer-Programmable Features section of the EVIC. The available choices are: OFF, Sound Only, or Sound and Display.
Page 145: Cleaning The Parksense System
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE detected a faulted condition, the EVIC will display the “CLEAN PARK ASSIST SENSORS” or the “SERVICE PARK ASSIST SYSTEM” message for as long as the vehicle is in REVERSE. Under this condition, ParkSense will not operate.
Page 146 • Clean the ParkSense sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The ParkSense system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/ bumper.
Page 147 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Drivers must be careful when backing up even when using the ParkSense Rear Park Assist Sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up.
Page 148: Parkview Rear Back Up Camera - If Equipped
PARKVIEW REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen along with a caution note to “check entire surroundings”...
Page 149: Turning Parkview On Or Off - With Navigation/Multimedia Radio
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage, ParkView should only be used as a parking aid. The ParkView camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.
Page 150: Overhead Console - If Equipped
OVERHEAD CONSOLE — IF EQUIPPED The overhead console is located on the headliner above the review mirror. The overhead console contains the following features: • Courtesy/Reading Lights • Power Sunroof Switch — If Equipped • Power Sliding Rear Window Switch — If Equipped •...
Page 151 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
Page 152: Garage Door Opener - If Equipped
GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink unit operates off your vehicle’s battery. The HomeLink buttons are located in the overhead console, and contain one, two or three dots/lines desig- nating the different HomeLink channels.
Page 153: Programming Homelink
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 154 • Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink buttons while keeping the EVIC display in view. For optimal training, point the battery end of the handheld transmitter away from the HomeLink • Simultaneously press and hold both the chosen HomeLink button and the handheld transmitter but- ton until the EVIC display changes from “CHANNEL # TRAINING”...
Page 155 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 1 — Garage Door Opener 2 —...
Page 156: Gate Operator/Canadian Programming
Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out”...
Page 157: Reprogramming A Single Homelink Button
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.”...
Page 158: General Information
General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
Page 159: Open Sunroof - Express Mode
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Power Accessory Delay feature will allow the power sunroof to operate for approximately ten minutes after the ignition is turned OFF or until a front door is opened. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
Page 160: Pinch Protect Feature
“Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract.
Page 161: Sunroof Maintenance
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.
Page 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 • Inside the top storage tray — with floor mounted • Inside the upper lid of the center storage compartment shifter. — if equipped. Power Outlet — Floor Shifter Power Outlet — Upper Lid...
Page 163 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Rear of the center console storage compartment — Quad Cab or Crew Cab. Power Outlet — Rear Center Console The key symbol indicates that this outlet can supply power when the key is in the ON/RUN or ACC posi- tions.
Page 164: Cigar Lighter And Ash Receiver - If Equipped
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
Page 165: Power Inverter - If Equipped
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For vehicles equipped with an optional floor shifter. Optional Floor Shifter 1 — Cigar Lighter 2 — Ash Receiver POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio.
Page 166 Power Inverter Outlet The power inverter switch is located on the switch bank below the Climate Controls. To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: •...
Page 167: Cupholders
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Instrument Panel Cupholders — (40–20–40 Seats) The cupholders are located in the pull-out tray at the bottom of the center stack. The pull-out tray must be secured when opened. To secure the tray push down until it “clicks”. Front Cupholders Front Instrument Panel Cupholders —...
Page 168: Rear Cupholder - Quad Cab
Rear Cupholder — Quad Cab Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cup wells for rear passenger convenience. Rear Cup Wells UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Rear Cupholder — Crew Cab Crew Cab vehicles are equipped with rear cupholders located in the center armrest.
Page 169: Storage
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Glove Box Storage The glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area. Glove Box 1 — Upper Glove Box 2 —...
Page 170 To open the upper glove box push upward on the handle release. The glove box door will automatically open. Upper Glove Box UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 To open the lower glove box, pull on the handle to release the latch and lower the door.
Page 171: Door Storage
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Storage Front Door Storage — If Equipped Storage areas and bottle holders (drivers side only) are located in the door trim panels. Front Door Storage Rear Door Storage — Crew Cab Storage compartments are located in both the driver and passenger door trim panels.
Page 172: Center Storage Compartment - If Equipped
Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Center Storage Compartment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 WARNING! •...
Page 173 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pull on the upper handle on the front of the armrest to raise the cover. The upper storage area contains a 12 Volt power outlet that can be used to power small electrical devices, refer to “Electrical Power Outlets”...
Page 174: Second Row In-Floor Storage Bin - If Equipped
Second Row In-Floor Storage Bin — If Equipped In-floor storage bins are located in front of the second row seats and can be used for extra storage. The storage bins have removable liners that can be easily removed for cleaning. In-Floor Storage Bin And Latch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 To open in-floor storage bin, lift upward on the handle of...
Page 175: Seatback Storage
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seatback Storage Located in the back of both the driver and passenger front seats are pockets that can be used for storage. Drivers Side Seatback Storage Storage (Regular Cab) The storage bin is located behind the front seats and runs the length of the cab.
Page 176: Plastic Grocery Bag Retainers (Regular Cab Models)
Crew Cab Storage CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind...
Page 177: Rear Window Defroster
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped).
Page 178: Power Sliding Rear Window - If Equipped
Power Sliding Rear Window — If Equipped The switch for the power sliding rear window is located on the overhead console. Press the left side of the switch to open the glass and the right side of the switch to close the glass.
Page 179 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. Load Floor In Open Position 3. Reverse the procedure to store the load floor. Unfolding The Load Floor 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position.
Page 180 Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor.
Page 181: Rambox - If Equipped
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RAMBOX — IF EQUIPPED The RamBox system is an integrated pickup box storage and cargo management system consisting of three fea- tures: • Integrated box side storage bins • Cargo extender/divider • Bed rail tie-down system RamBox Integrated Box Side Storage Bins Cargo storage bins are located on both sides of the pickup box.
Page 182 CAUTION! Failure to follow the following items could cause damage to the vehicle: • Assure that all cargo inside the storage bins is properly secured. • Do not exceed cargo weight rating of 150 lb (68 kg) per bin. To open a storage bin, press and release the button located on the lid.
Page 183 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The interior of the RamBox will automatically illumi- nate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch located at the rear of each storage bin. Pushing the switch once will turn off the bin lights, pushing the switch again will turn the lights back on.
Page 184: Rambox Safety Warning
CAUTION! (Continued) • Loads applied to the top of the bin lid should be minimized to prevent damage to the lid and latching/hinging mechanisms. • Damage to the RamBox bin may occur due to heavy/sharp objects placed in bin that shift due to vehicle motion.
Page 185: Bed Extender - If Equipped
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RamBox Storage Bin Cover Emergency Release Lever — If Equipped As a security measure, a Storage Bin Cover Emergency Release is built into the storage bin cover latching mecha- nism. Storage Bin Cover Emergency Release Lever NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pulling on the glow-in-the-dark lever...
Page 186 To install the bed extender into the storage position, perform the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates. Center Handle and Lock 1 —...
Page 187 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops. Cargo Tie Down Loop 4. Rotate the center handle horizontally to secure the side gates in the closed position.
Page 188 Divider Position The divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions to assist in managing your cargo.
Page 189 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. With the side gates open, position the extender so the outboard ends align with the intended slots in the sides of the bed. Aligning Gate To Slots 3. Rotate the side gates closed so that the outboard ends are secured into the intended slots of the bed.
Page 190 Extender Position The extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed. The extender position utilizes a locating pin and rotating handle located on both sides of the truck bed near the tailgate.
Page 191 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Fit the end of the side gate ends onto the pin and handle. Extender Installation 4. Rotate the handles to the horizontal position to secure into place. Locking Tab...
Page 192: Bed Rail Tie-Down System
WARNING! To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. • Secure all loads to truck utilizing cargo tie downs. • Extender should not be used as cargo tie down. •...
Page 193 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are two adjustable cleats on each side of the bed that can be used to assist in securing cargo. Adjustable Cleats Each cleat must be located and tightened down in one of the detents, along either rail, in order to keep cargo properly secure.
Page 194: Slide-In Campers
To remove the cleats from the utility rail, remove the end cap by pushing up on the locking tab, located on the bottom of the end cap. Slide the cleat off the end of the rail. Utility Rail End Cap UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 SLIDE-IN CAMPERS Camper Applications...
Page 195: Disconnecting The Rear Camera - If Equipped
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Disconnecting the Rear Camera — If Equipped 1. Open the tailgate to access the rear camera connector bracket located on the rear sill. Connector Bracket 2. Remove the connector bracket from the sill by press- ing inward in the locking tab.
Page 196: Removing The Tailgate
5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate. This will prevent damaging the connector and bracket when storing or reinstalling the tailgate.
Page 197: Locking Tailgate
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Remove the tailgate from the vehicle. NOTE: Do not carry the tailgate loose in the truck pickup box. WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers”...
Page 198: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....201 Switch Bank Button Description ... 202 Upper Switch Bank .
Page 199 198 UNDERSTANDING YOUR INSTRUMENT PANEL Customer-Programmable Features (System Setup) ..... . 238 Media Center 730N/430/430N (RER/RBZ/ RHB) CD/DVD/HDD/NAV — If Equipped . . . 244 Operating Instructions (Voice Command System) —...
Page 200 Universal Consumer Interface (UCI) 0.5 — If Equipped ......270 Connecting The iPod ....271 Using This Feature .
Page 201 200 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Controls ..... . 285 Manual Heating And Air Conditioning System ......286 Automatic Temperature Control (ATC) —...
Page 202: Instrument Panel Features
INSTRUMENT PANEL FEATURES 1 — Headlight Switch 2 — Instrument Cluster 3 — Radio 4 — Upper Switch Bank 5 — Upper Glove Compartment 6 — Lower Glove Compartment UNDERSTANDING YOUR INSTRUMENT PANEL 201 7 — 115v Power Inverter Outlet 8 —...
Page 203: Switch Bank Button Description
202 UNDERSTANDING YOUR INSTRUMENT PANEL SWITCH BANK BUTTON DESCRIPTION Upper Switch Bank The upper switch bank is located on the center of the instrument panel. 1. TOW/HAUL Refer to “Starting And Operating” for more information. 2. ESC OFF Refer to “Starting And Operating” for more information. 3.
Page 204: Lower Switch Bank
Lower Switch Bank The lower switch bank is located on the center of the instrument panel. UNDERSTANDING YOUR INSTRUMENT PANEL 203 1. HEATED SEATS Refer to “Understanding The Features Of Your Vehicle” for more information. 2. VENTILATED SEATS Refer to “Understanding The Features Of Your Vehicle” for more information.
Page 205: Instrument Cluster - Base
204 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE...
Page 206: Instrument Cluster - Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 205 INSTRUMENT CLUSTER — PREMIUM...
Page 207: Instrument Cluster Descriptions
206 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Tachometer The tachometer indicates engine speed in Revolutions Per Minute (RPM). CAUTION! Do not operate the engine with the tachometer pointer at high RPM for extended periods. Engine damage may occur. 2.
Page 208 CAUTION! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”...
Page 209 208 UNDERSTANDING YOUR INSTRUMENT PANEL rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. For further information on four-wheel drive operation and proper use, refer to “Four-Wheel Drive Operation — If Equipped”...
Page 210 9. 4WD Auto Indicator The 4WD auto indicator will be illuminated whenever the four-wheel drive mode is auto- matically engaged. 10. SERV (Service) 4WD The SERV 4WD light monitors the electric shift four-wheel drive system. If the SERV 4WD light stays on or comes on during driving, it means that the four-wheel drive system is not functioning properly and that service is required.
Page 211 210 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on mo- mentarily each time the ignition switch is turned to ON/RUN. • Each time the ignition is turned to ON/RUN, the ESC system will be ON even if it was turned off previously.
Page 212 16. Odometer Display / Electronic Vehicle Information Center (EVIC) Display Area — If Equipped Odometer Display The odometer shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
Page 213 212 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: There is also an engine hour function. This indicates the total number of hours the engine has been running. To display the engine hours on the base cluster, perform the following: Place the ignition in the ON/ RUN, but do not start the engine.
Page 214 Lo tirE When the appropriate condition exists, the odometer display will toggle between Lo and tirE for three cycles. noFUSE If the vehicle diagnostic system determines that the Ignition Off Draw (IOD) fuse is improperly installed, or damaged, a “noFUSE” message will display in the odom- eter display area.
Page 215 214 UNDERSTANDING YOUR INSTRUMENT PANEL 17. Engine Temperature Warning Light This light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H, the indicator will continuously flash and a continuous chime will occur until the engine is allowed...
Page 216 For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. 20. High Beam Indicator This indicator shows that headlights are on high beam.
Page 217 216 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Program (ESP) sys- tem.
Page 218 Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected.
Page 219 218 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated.
Page 220 tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle.
Page 221 220 UNDERSTANDING YOUR INSTRUMENT PANEL Although your vehicle will usually be drivable and not need towing, see your authorized dealer for service as soon as possible. CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability.
Page 222 28. Front Fog Light Indicator — If Equipped This indicator will illuminate when the front fog lights are on. 29. Anti-Lock Brake (ABS) Light This light monitors the Anti-lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and may stay on for as long as four seconds.
Page 223 222 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Continued operation with the Transmission Tem- perature Warning Light illuminated could cause the fluid to boil over, come in contact with hot engine or exhaust components causing a fire that may result in personal injury. For vehicles equipped with a premium cluster this warn- ing light will display in the Electronic Vehicle Informa- tion Center (EVIC).
Page 224: Electronic Vehicle Information Center (Evic) - If Equipped
For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. 33. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Con- trol (ESC) is off.
Page 225 224 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: • System Status display • Vehicle information warning message displays •...
Page 226: Evic Displays
Steering wheel EVIC control button, as it appears on the right side of the steering wheel. Press and release the SELECT button for access to main menus, sub menus or to select a personal setting in the system setup menu. Press the BACK button to scroll back to a previous menu or sub menu.
Page 227 226 UNDERSTANDING YOUR INSTRUMENT PANEL • Lights On • Keyfob Battery Low • ECO (Fuel Saver Indicator) — If Equipped • Door(s) Ajar (with a single chime, if vehicle is in motion) • Wrong Key • Damaged Key • Key not programmed •...
Page 228 • Remote start aborted — Fuel low • Remote start disabled — System fault • Remote start disabled — Turn key • Remote start active — Key to Run • Remote Start Disabled — Start Vehicle to Reset • Remote Start Active — Insert Key and Turn to RUN •...
Page 229 228 UNDERSTANDING YOUR INSTRUMENT PANEL Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • Charging System Light This light shows the status of the electrical charg- ing system.
Page 230 If the light remains lit with the engine running your vehicle, will usually be drivable, however, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing.
Page 231 230 UNDERSTANDING YOUR INSTRUMENT PANEL • Transmission Temperature Light This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.g., snow plowing, off- road operation).
Page 232: Fuel Economy / Fuel Saver Mode / Distance
Oil Change Due Your vehicle is equipped with an engine oil change indicator system. The Oil Change Due message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style.
Page 233 232 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Saver Mode The FUEL SAVER MODE message will display above the average fuel economy in the EVIC display. This message will appear whenever MDS (if equipped) allows the engine to operate on four cylinders, or if you are driving in a fuel efficient manner.
Page 234: Trip Functions
significant amount of fuel to the vehicle will turn off the LOW FUEL text and a new DTE value will display. Trip Functions Press and release the ODOMETER/TRIP ODOMETER button until one of the following Trip Functions displays in the EVIC: •...
Page 235: Vehicle Info
234 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Info (Customer Information Features) Press and release the UP or DOWN button until “Vehicle Info” displays in the EVIC and press the SELECT button. Press the UP and DOWN button to scroll through the available information displays, then press SELECT to display anyone of the following choices.
Page 236: Units
Tire Pressure Display NOTE: • Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer UNDERSTANDING YOUR INSTRUMENT PANEL 235 to “Tires-General Information/Tire Inflation Pres- sures”...
Page 237: Compass / Temperature Display
236 UNDERSTANDING YOUR INSTRUMENT PANEL Compass / Temperature Display The compass readings indicate the direction the vehicle is facing. The EVIC will display one of eight compass readings and the outside temperature. NOTE: • The system will display the last known outside tem- perature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed.
Page 238 NOTE: A good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Manual Compass Calibration If the compass appears erratic and the CAL indicator does not appear in the EVIC display, you must put the compass into the Calibration Mode manually, as follows: 1.
Page 239: Customer-Programmable Features (System Setup)
238 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Map 1. Turn the ignition switch ON. 2. Press the UP or DOWN button until the System Setup (Customer-Programmable Features) menu is reached, then press the SELECT button. 3. Press the DOWN button until the “Compass Variance” message is displayed in the EVIC, then press the SELECT button.
Page 240 Use the UP or DOWN button to display one of the following choices. Select Language When in this display you may select one of five lan- guages for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the UP or DOWN button while in this display and scroll through the language choices.
Page 241 240 UNDERSTANDING YOUR INSTRUMENT PANEL (24 km/h). To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated.
Page 242 system has been activated or the check-mark is removed, showing the system has been deactivated. Remote Start Comfort Sys. When this feature is selected and the remote start is activated, the heated steering wheel and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated.
Page 243 242 UNDERSTANDING YOUR INSTRUMENT PANEL To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. Headlamp Off Delay When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds...
Page 244 and release the SELECT button until a check-mark ap- pears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set to ON) when the RKE transmitter is used to unlock the door.
Page 245: Media Center 730N/430/430N (Rer/Rbz/Rhb) Cd/Dvd/Hdd/Nav - If Equipped
244 UNDERSTANDING YOUR INSTRUMENT PANEL Hill Start Assist (HSA) When on is selected, the HSA system is active. Refer to “Electronic Brake Control System” in “Starting And Operating” for system function and operating informa- tion. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been...
Page 246: Operating Instructions (Uconnect™ Phone) - If Equipped
Operating Instructions (Uconnect™ Phone) — If Equipped Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. MEDIA CENTER 130 (SALES CODE RES) NOTE: The radio sales code is located on the lower right side of the radio faceplate.
Page 247 246 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
Page 248 RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency.
Page 249: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
248 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window.
Page 250 discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display.
Page 251 250 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF.
Page 252: Notes On Playing Mp3 Files
Notes on Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 253 252 UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as keep disc open after writing are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 exten- sion as MP3 files.
Page 254: Operation Instructions - Auxiliary Mode
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: •...
Page 255: Media Center 130 With Satellite Radio (Sales Code Res+Rsc)
254 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 WITH SATELLITE RADIO (SALES CODE RES+RSC) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Media Center 130 (RES/RSC) Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio.
Page 256 SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
Page 257 256 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes.
Page 258 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display.
Page 259 258 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: 16-Digit Character Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies Program Type Personality Display Public...
Page 260 By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
Page 261: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
260 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 262 If you insert a disc with the ignition ON/RUN and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds.
Page 263: Notes On Playing Mp3 Files
262 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or...
Page 264 Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally.
Page 265 264 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
Page 266: List Button (Cd Mode For Mp3 Play)
Loading times for playback of MP3 files may be affected by the following: • Media - CD-RW media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs •...
Page 267: Uconnect™ Multimedia (Satellite Radio) - If Equipped
266 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 268 information, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www- .siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
Page 269 268 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
Page 270 additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows.
Page 271: Operating Instructions (Uconnect™ Phone) - If Equipped
270 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button.
Page 272: Connecting The Ipod
This feature allows an iPod to be plugged into the vehicle’s sound system through a 16–pin connector, using the provided interface cable. UCI supports Mini, 4G, Photo, Nano, 5G iPod iPhone devices. Some iPod software versions may not fully support the UCI features. Please visit Apple’s website for software updates.
Page 273: Using This Feature
272 UNDERSTANDING YOUR INSTRUMENT PANEL Using This Feature By using the provided connection cable to connect an iPod to the vehicle’s UCI 16–pin connector port: • The iPod audio can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.) information on the radio display.
Page 274 • Jump backward in the current track by pressing and holding the << RW button. Holding the << RW button long enough will jump to the beginning of the current track. • Jump forward in the current track by pressing and holding the FF >>...
Page 275: List Or Browse Mode
274 UNDERSTANDING YOUR INSTRUMENT PANEL • RND button (available on sales code RES radio only): Pressing this button toggles between Shuffle ON and Shuffle OFF modes for the iPod . If the RND icon is showing on the radio display, then the shuffle mode is List Or Browse Mode During Play mode, pressing any of the buttons described below, will bring up List mode.
Page 276 • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • To Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode.
Page 277: Universal Consumer Interface (Uci) 1.0 - If Equipped
276 UNDERSTANDING YOUR INSTRUMENT PANEL UNIVERSAL CONSUMER INTERFACE (UCI) 1.0 — IF EQUIPPED NOTE: This section is for sales code RES and REQ/ REL/RET radios only with Uconnect™. For sales code RER, REN, RBZ, REP, REW, RB2 or REZ touch-screen radio UCI feature, refer to the separate RER, REN, RBZ, RB2 or REZ User’s Manual.
Page 278: Using This Feature
Using This Feature By using iPod cable or external USB device to connect to USB port: • The device audio can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.) information on the radio display. •...
Page 279 278 UNDERSTANDING YOUR INSTRUMENT PANEL • Jump backward in the current track by pressing and holding the << RW button. Holding the << RW button long enough will jump to the beginning of the current track. • Jump forward in the current track by pressing and holding the FF >>...
Page 280: List Or Browse Mode
device, or press VR button and say Shuffle ON or Shuffle Off . If the RND icon is showing on the radio display, then the shuffle mode is ON. List Or Browse Mode During Play mode, pressing any of the buttons described below, will bring up List mode.
Page 281 280 UNDERSTANDING YOUR INSTRUMENT PANEL • Preset 6 – Podcasts • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • To Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode.
Page 282: Bluetooth Streaming Audio (Btsa)
WARNING! Do not plug in or remove the iPod or external USB device while driving. Failure to follow this warning could result in an accident. Bluetooth Streaming Audio (BTSA) Music can be streamed from your cellular phone to the Uconnect™ phone system. Controlling BTSA using Radio Buttons To get into the BTSA mode, press either “AUX”...
Page 283: Video Entertainment System (Ves)™ - If Equipped
282 UNDERSTANDING YOUR INSTRUMENT PANEL Browse Browsing is not available on a BTSA device. Only the current song that is playing will display info. VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED The optional Video Entertainment System (VES)™ is available with: •...
Page 284: Steering Wheel Audio Controls - If Equipped
VES™ Remote Control Location NOTE: Refer to the “Uconnect™ Multimedia” section of Uconnect™ User Manual located on the DVD for further details. UNDERSTANDING YOUR INSTRUMENT PANEL 283 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel.
Page 285: Radio Operation
284 UNDERSTANDING YOUR INSTRUMENT PANEL The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch will increase the volume, and pressing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to Radio, CD or other valid audio source.
Page 286: Cd/Dvd Disc Maintenance
CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3.
Page 287: Manual Heating And Air Conditioning System
286 UNDERSTANDING YOUR INSTRUMENT PANEL throughout the vehicle. The controls are located on the instrument panel below the radio. NOTE: During snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient tempera- ture.
Page 288 Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the OFF position.
Page 289 288 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-Level Mode Air is directed through the panel and floor outlets. NOTE: There is a difference in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort.
Page 290 Recirculation Control Press this button to choose between outside air intake or recirculation of the air inside the vehicle. A LED will illuminate when you are in Recircula- tion mode. Only use the Recirculation mode to temporarily block out any outside odors, smoke, or dust, and to cool the interior rapidly upon initial start-up in very hot or humid weather.
Page 291: Automatic Temperature Control (Atc) - If Equipped
290 UNDERSTANDING YOUR INSTRUMENT PANEL Economy Mode If ECONOMY mode is desired, press the A/C button to turn off the LED indicator and the A/C compressor. Rotate the temperature control knob to the desired temperature. Air Conditioning Operation Push this button to engage the Air Conditioning (A/C).
Page 292 • SYNC feature links the temperature controls, the pas- senger side temperature becomes the same as the temperature selected by the driver. The ATC system automatically maintains the interior comfort level desired by the driver and all passengers. UNDERSTANDING YOUR INSTRUMENT PANEL 291 Automatic Temperature Control (ATC) Panel 1 - Blower Control 9 - DEFROST...
Page 293 292 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Operation 1. Position the MODE control knob to the Auto position on the Automatic Temperature Control (ATC) Panel. 2. Position the BLOWER control knob in the Auto posi- tion on the ATC Panel. 3. Next, adjust the temperature you would like the system to maintain by adjusting the driver and front passenger temperature buttons.
Page 294 blower will engage immediately if the Defrost mode is selected, or by adjusting the blower control knob and setting the fan to any fixed speed. Manual Operation This system offers a full complement of manual override features. NOTE: Each of these features operate independently from each other.
Page 295 294 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In many temperature positions, the BI-LEVEL mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets. Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.
Page 296: Summer Operation
Recirculation Control When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the RECIRCULATION control button. Recirculation mode should only be used temporarily. The recirculation LED will illuminate on the blower control knob when this button is selected.
Page 297: Vacation/Storage
296 UNDERSTANDING YOUR INSTRUMENT PANEL Vacation/Storage Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in fresh air with the blower setting in high. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
Page 298: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 297 Operating Tips...
Page 300: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....305 Normal Starting ..... 305 Automatic Transmission .
Page 301 300 STARTING AND OPERATING Transfer Case Position Indicator Light ..327 Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped ..327 Shifting Procedure ....331 Electronically Shifted Transfer Case (Five-Position Switch) –...
Page 302 Shallow Standing Water ....363 Off-Road Driving Tips ....364 After Driving Off-Road .
Page 303 302 STARTING AND OPERATING ESC Activation/Malfunction Indicator Light And ESC Off Indicator Light ... . 399 Trailer Sway Control (TSC) – If Equipped . . . 400 Tire Safety Information ....401 Tire Markings .
Page 304 Base System ......426 Premium System – If Equipped ..428 Tire Pressure Monitor System (TPMS) Tire Light Load Inflation Switch Description (2500 Models) –...
Page 305 304 STARTING AND OPERATING Adding Fuel ......444 Loose Fuel Filler Cap Message ... 446 Vehicle Loading .
Page 306: Starting Procedures
STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! Never leave children alone in a vehicle.
Page 307: If Engine Fails To Start
306 STARTING AND OPERATING If Engine Fails To Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
Page 308: After Starting
accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key fob once the engine is running smoothly. If the engine shows no sign of starting after two 15- second periods of cranking with the accelerator pedal held to the floor, the “Normal Starting”...
Page 309: Automatic Transmission
308 STARTING AND OPERATING WARNING! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: •...
Page 310: Key Ignition Park Interlock
Key Ignition Park Interlock This vehicle is equipped with a Key Ignition Park Inter- lock which requires the shift lever to be placed in PARK prior to turning the key fob to the LOCK position. The key fob can only be removed from the ignition switch when the ignition is in the LOCK position and once removed the shift lever is locked in PARK.
Page 311 310 STARTING AND OPERATING 5. Using a screwdriver or other suitable tool, press and hold the override tab through the access port (ringed circle) on the bottom of the steering column. Interlock Manual Override 6. Move the shift lever into the NEUTRAL position. 7.
Page 312: Four-Speed Automatic Transmission - If Equipped
4. Using the screwdriver, press and hold the override tab through the access port on the center console. Interlock Manual Override 5. Move the shift lever into the NEUTRAL position. 6. The vehicle may then be started in NEUTRAL. 7. Reinstall the override cover. STARTING AND OPERATING 311 Four–Speed Automatic Transmission –...
Page 313 312 STARTING AND OPERATING PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever in the PARK position.
Page 314 WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into PARK, remove the key fob from the ignition, and apply the parking brake.
Page 315 314 STARTING AND OPERATING Overdrive Operation The Overdrive automatic transmission contains an elec- tronically controlled fourth gear (OVERDRIVE). The transmission will automatically shift from third gear to OVERDRIVE if the following conditions are present: • the shift lever is in DRIVE •...
Page 316 performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in TOW/HAUL mode, the transmission will shift to third gear and fourth gear will be enabled under steady cruise conditions. TOW/HAUL Switch STARTING AND OPERATING 315 The “TOW/HAUL Indicator Light”...
Page 317: Five-Speed Automatic Transmission - If Equipped
316 STARTING AND OPERATING 3. Turn OFF the engine and be sure to turn the key fob to the LOCK position. 4. Wait approximately 10 seconds, then restart the en- gine. 5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation.
Page 318 lever left (-) or right (+), or toggle the switch on the column shift lever down (-) or up (+) to select the desired top gear. For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second gear) or 1 (first gear), when needed.
Page 319 318 STARTING AND OPERATING through third gear are underdrive gears, and fourth gear is direct drive. ERS fifth gear (Overdrive) is the same as the normal fourth gear. When in the DRIVE position in first through fourth gear, the first tap down (-), will display the ERS designation for the current gear (the transmission will not downshift).
Page 320 Gear Ranges Do not race the engine when shifting from PARK or NEUTRAL position into another gear range. PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range.
Page 321 320 STARTING AND OPERATING WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into PARK, remove the key fob from the ignition, and apply the parking brake.
Page 322 Overdrive Operation The Overdrive automatic transmission contains an elec- tronically controlled fourth and fifth gear (Overdrive). The transmission will automatically shift from DRIVE to Overdrive if the following conditions are present: • the shift lever is in DRIVE; • the engine coolant (antifreeze) has reached normal operating temperature;...
Page 323 322 STARTING AND OPERATING performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in the TOW/HAUL mode, fifth gear is dis- abled and 2-3 and 3-4 shift patterns are modified. TOW/HAUL Switch Shifts into Overdrive (fourth gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to third gear are performed (for improved braking) when driving conditions warrant.
Page 324: Four-Wheel Drive Operation - If Equipped
NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant (antifreeze) are warm [usually after 1 to 3 miles (1.6 to 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold.
Page 325 324 STARTING AND OPERATING When additional traction is required, the 4H and 4L positions can be used to lock the front and rear drive- shafts together and force the front and rear wheels to rotate at the same speed. This is accomplished by simply moving the shift lever to the desired positions.
Page 326 NOTE: Delayed shifts out of four-wheel drive may be experienced due to uneven tire wear, low or uneven tire pressures, excessive vehicle loading, or cold tempera- tures. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
Page 327: Shifting Procedure - Manually Shifted Transfer Case
326 STARTING AND OPERATING and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting Procedure – Manually Shifted Transfer Case 2H ⇔ 4H Shifting between 2H and 4H can be made with the vehicle stopped or in motion.
Page 328: Transfer Case Position Indicator Light
Transfer Case Position Indicator Light The “Transfer Case Position Indicator Light” in the instrument cluster is used to alert the driver that the front axle is fully engaged and all four wheels are driving. Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped This is an electronic shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel.
Page 329 328 STARTING AND OPERATING • Neutral (NEUTRAL) This electronically shifted transfer case is designed to be driven in the two-wheel drive position (2WD) for normal street and highway conditions on dry, hard surfaced roads. When additional traction is required, the transfer case 4WD LOCK and 4WD LOW positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.
Page 330 3. When the shift is complete, the indicator light for the selected position will stop flashing and remain ON. If One Or More Shift Conditions Are Not Met: 1. The indicator light for the current position will remain 2. The newly selected position indicator light will con- tinue to flash.
Page 331 330 STARTING AND OPERATING When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h).
Page 332: Shifting Procedure
4WD LOCK Four-Wheel Drive Lock Range - This range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. This range provides additional traction for loose, slippery road surfaces only. 4WD LOW Four-Wheel Drive Low Range - This range provides low speed four-wheel drive.
Page 333 332 STARTING AND OPERATING When the shift is complete, the position indicator light for the selected position will stop flashing and remain 2WD⇔ 4WD LOCK Rotate the 4WD control switch to the desired position. Shifts between 2WD and 4WD LOCK can be done with the vehicle stopped or in motion.
Page 334 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift the transmission back into gear. Alternate Procedure 1. Bring the vehicle to a complete stop. 2.
Page 335: Electronically Shifted Transfer Case (Five-Position Switch) - If Equipped
334 STARTING AND OPERATING Electronically Shifted Transfer Case (Five-Position Switch) – If Equipped This is an electronic shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel. Transfer Case Switch (Five–Position) This electronically shifted transfer case provides five mode positions: •...
Page 336 drive will be automatically engaged when the vehicle senses a loss of traction. Because the front axle is en- gaged, this mode will result in lower fuel economy than the 2WD mode. When additional traction is required, the transfer case 4WD LOCK and 4WD LOW positions can be used to lock the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed.
Page 337 336 STARTING AND OPERATING If One Or More Shift Conditions Are Not Met: 1. The indicator light for the current position will remain 2. The newly selected position indicator light will con- tinue to flash. 3. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met.
Page 338 AUTO or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel.
Page 339: Shifting Procedure
338 STARTING AND OPERATING 4WD AUTO Four-Wheel Drive Auto Range - This range sends power to the rear wheels. The four–wheel drive system will be automatically engaged when the vehicle senses a loss of traction. Additional traction for varying road conditions. 4WD LOCK Four-Wheel Drive Lock Range - This range locks the front and rear driveshafts together forcing the front and rear...
Page 340 • If all the requirements to select a new transfer case position have been met, the current position indicator light will turn OFF, the selected position indicator light will flash until the transfer case completes the shift. When the shift is complete, the position indicator light for the selected position will stop flashing and remain 2WD ⇔...
Page 341: Axle Locker System (2500 Models Only) - If Equipped
340 STARTING AND OPERATING Alternate Procedure 1. Bring the vehicle to complete stop. 2. With the ignition switch in the ON position and the engine either OFF or running, shift the transmission into NEUTRAL. 3. Rotate the transfer case control switch to the desired position.
Page 342 CAUTION! • Do not lock the front or rear axle on hard surfaced roads. The ability to steer the vehicle is reduced and damage to the drivetrain may occur when the axles are locked on hard surfaced roads. • Do not try to lock the rear axle if the vehicle is stuck and the tires are spinning.
Page 343 342 STARTING AND OPERATING NOTE: Left to right wheel speed difference may be necessary to allow the axle to fully lock. If the indicator light is flashing after placing the switch in the REAR LOCK or FRONT/REAR LOCK position, drive the ve- hicle in a turn or on loose gravel to expedite the locking action.
Page 344: Safe Off-Road Driving - Power Wagon Only
SAFE OFF-ROAD DRIVING — POWER WAGON ONLY Off-Road Driving Tips and Vehicle Characteristics Your vehicle has excellent on and off-road capabilities. These off-road capabilities will allow you to explore those wilderness trails where few travel, providing a source of exciting and satisfying recreation. Before you venture out, you should contact your local governmental agency to determine the designated off-road vehicle (ORV) trails or recreation areas.
Page 345 344 STARTING AND OPERATING high water fording characteristics with the ability to cross a pool of water, without stopping, 24 inches deep at a maximum speed of 10 mph (16 km/h) and a pool of water 30 inches deep at a maximum speed of 5 mph (8 km/h), both with an entrance ramp angle of 1.3 degrees.
Page 346: Driving In Snow, Mud And Sand
CAUTION! Never park your vehicle over dry grass or other combustible materials. The heat from your vehicle exhaust system could cause a fire. WARNING! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation.
Page 347 346 STARTING AND OPERATING no more than a ⁄ turn quickly back and forth, while still applying throttle. This will allow the tires to get a fresh bite and help maintain your momentum. CAUTION! On icy or slippery roads, do not downshift at high engine RPMs or vehicle speeds because engine brak- ing may cause skidding and loss of control.
Page 348: Crossing Obstacles (Rocks And Other High Points)
CAUTION! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneu- vers. Crossing Obstacles (Rocks And Other High Points) While driving off road, you will encounter many types of terrain.
Page 349 348 STARTING AND OPERATING Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest with your tires. This will lift your undercarriage over the obstacle. The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.
Page 350: Hill Climbing
accelerator to avoid spinning the log out from under your tires. Then ease the vehicle off the log using your brakes. CAUTION! Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high centered.
Page 351 350 STARTING AND OPERATING the vehicle if something goes wrong? If everything looks good and you feel confident, then change trans- mission into a lower gear, shift the transfer case into 4L (Low) and proceed with caution. You should use first gear and 4L (Low Range) for very steep hills.
Page 352 ability to proceed then make sure you are in 4L (Low Range) with the transmission in first gear (manually select first gear on automatic transmissions) and pro- ceed with caution. Allow engine braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock.
Page 353: Driving Through Water
352 STARTING AND OPERATING WARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury.
Page 354 CAUTION! Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or muddy •...
Page 355: Airing Down For Off-Road Driving
354 STARTING AND OPERATING CAUTION! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. • Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water – Flowing water can be extremely dangerous. Never attempt to cross a fast running stream or river even in shallow water.
Page 356: Vehicle Recovery
form to the ground contour. Different terrain, tires, and vehicles require different tire pressure. Hard surfaces like rock and heavier vehicles require higher pressures than softer surfaces such as sand and lighter vehicles. You will need to experiment to determine what is right for your situation.
Page 357 356 STARTING AND OPERATING vehicle impingement on the surroundings, then using a tow strap to the vehicle tow hooks would be fast and easy. If the vehicle is severely hung up or in a situation where great care needs to be taken during the recovery, then nothing can do the job better than a winch.
Page 358 CAUTION! Damage can occur when spinning your tires at an excessive high speed. Do not spin your tires faster than an indicated 35 mph (56 km/h). • Using the Tow Hooks With a Tow Strap – Tow straps are a quick and easy way to recover your vehicle from minor situations if you have a secondary vehicle which is not stuck.
Page 359 358 STARTING AND OPERATING WARNING! Never use tow straps with end hooks or link two straps with a clevis pin. These heavy metal objects could become projectiles if a strap breaks, which could cause severe injury. Never leave more than two or three feet of slack in the strap.
Page 360: After Driving Off-Road
as you power the winch in. Be careful not to allow slack in the cable as you recover the vehicle. Do not try to guide the cable into the drum. If it starts to bunch up on one end, let it. You can re-spool the cable afterwards.
Page 361: Limited-Slip Differential
360 STARTING AND OPERATING • After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.
Page 362: Driving On Slippery Surfaces
WARNING! On vehicles equipped with a limited-slip differential never run the engine with one rear wheel off the ground since the vehicle may drive through the rear wheel remaining on the ground. You could lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface.
Page 363: Traction
362 STARTING AND OPERATING Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
Page 364: Shallow Standing Water
Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
Page 365: Off-Road Driving Tips
364 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances.
Page 366 always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage.
Page 367: Winch Usage (Power Wagon Only) - If Equipped
366 STARTING AND OPERATING WINCH USAGE (POWER WAGON ONLY) — IF EQUIPPED Things To Know Before Using Your Winch General Winch Information Your vehicle is equipped with an electric vehicle recovery winch. This winch uses the electrical power from the vehicle charging system to power a motor that winds wire rope into the winch drum via planetary gear reduc- tion.
Page 368 Low Voltage Interrupt Your winch is equipped with a device that will interrupt winch function if the vehicle charging system voltage drops to a low level. The winch will not power-in or out for 30 seconds if this device is tripped. If the interrupt is tripped, the vehicle should be operated at high idle for a few minutes to allow the vehicle charging system to recover before continuing to winch.
Page 369: Understanding The Features Of Your Winch
368 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components...
Page 370 1. Motor: The winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote Socket: The remote socket allows the remote control to be attached to the control pack to allow the winch to function.
Page 371: Winch Accessories
370 STARTING AND OPERATING Winch Accessories The following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: Wire rope, through use, which can slice skin. It is ex- tremely important to wear pro- tective gloves while operating the winch or handling the wire rope.
Page 372: Operating Your Winch
Clevis/D-Shackles: Operating Your Winch D-Shackle is a safe means of connecting the looped ends of cables, straps and snatch Failure to observe any of these warnings regarding blocks. The shackle’s pin is proper winch usage may result in severe injury. threaded to allow easy re- •...
Page 373 372 STARTING AND OPERATING WARNING! (Continued) • Always stand clear of wire rope and load and keep others away during winching. • Always keep hands and clothing clear of the wire rope, hook and fairlead opening during operation and when spooling. •...
Page 374 General Information Practice using your winch before you get stuck. Some key points to remember when using your winch are: 1. Always take your time to assess the situation and plan your pull carefully. 2. Always take your time when using a winch. 3.
Page 375 374 STARTING AND OPERATING CAUTION! (Continued) • Always keep remote control lead clear of the drum, wire rope and rigging. • Inspect for cracks, pinches, frayed wires, or loose connections. Replace if damaged. • Be careful not to pull the Winch Cable Collar through the rollers.
Page 376 3. Disengage the clutch to allow free spooling of the winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserves battery power. Free Spool 4. Free the winch hook and attach the hook strap. Free the winch hook from its anchor point. Attach the hook strap to the hook (if not attached).
Page 377 376 STARTING AND OPERATING 6. Secure to the anchor point. Once you have established your anchor point, secure the tree-trunk protector or choker-chain around the object. Tree Trunk Protector CAUTION! Always be certain the anchor you select will with- stand the load.
Page 378 NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural an- chors include trees, stumps and rocks. Hook the cable as low as possible. If no natural anchors are available when recovering another vehicle, your vehicle becomes the anchor point.
Page 379 378 STARTING AND OPERATING 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door.
Page 380 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. STARTING AND OPERATING 379 13. In certain situations you may decide to throw a heavy blanket or similar object over the wire rope.
Page 381 380 STARTING AND OPERATING the vehicle and never near the wire rope or snatch block. Your situation may have other no people zones. No People Zones 15. Begin winching. With the winching vehicles engine on and light tension already on the wire rope, begin winching slowly and steadily.
Page 382 NOTE: • Avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the winch motor to cool down. • What to look for under load: The wire rope must always spool onto the drum as indicated by the drum rotation decal on the winch.
Page 383 382 STARTING AND OPERATING 18. Rewind the wire rope. The person handling the wire rope should walk the rope in and not let it slide through the hand, control the winch at all times. WARNING! To prevent serious injury, NEVER put your fingers inside the hook area as you are powering-in.
Page 384: Rigging Techniques
wire rope towards the fairlead, carefully spooling in the remaining wire rope. By pulsing the remote control switch. 19. Store the hook on the most outboard loop of the tow hook. STARTING AND OPERATING 383 20. Disconnect the remote control. Disconnect the remote control cord from the control box and store in a clean and dry place.
Page 385 384 STARTING AND OPERATING How to Change the Pulling Direction Change Pulling Directions All winching operations should have a straight line from the winch to the object being pulled. This minimizes the wire rope collecting on one side of the drum affecting pulling efficiency and damaging wire rope.
Page 386: Power Steering
Double Line Because pulling power decreases with the number of layers of wire rope on the winch drum, you can use a snatch block to double line out more wire rope. This decreases the number of layers of wire rope on the drum, and increases pulling power.
Page 387: Power Steering Fluid Check
386 STARTING AND OPERATING NOTE: • Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system. • Upon initial start-up in cold weather, the power steer- ing pump may make noise for a short amount of time.
Page 388: Multi-Displacement System (Mds) (If Equipped) - 5.7L Engine Only
CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New Vehicle Limited Warranty. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading.
Page 389 388 STARTING AND OPERATING The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, pull the parking brake release handle.
Page 390 make it difficult to move the shift lever out of PARK. The parking brake should always be applied whenever the driver is not in the vehicle. WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
Page 391: Brake System
390 STARTING AND OPERATING BRAKE SYSTEM If power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, you will experience a substantial increase in braking effort to stop the vehicle. If either the front or rear hydraulic system loses normal braking capability, the remaining system will still func- tion with some loss of overall braking effectiveness.
Page 392: Traction Control System (Tcs) - If Equipped
NOTE: ABS improves steering control of the vehicle during hard braking maneuvers. WARNING! • ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that af- forded by the condition of the vehicle brakes and tires or the traction afforded.
Page 393: Brake Assist System (Bas) - If Equipped
392 STARTING AND OPERATING Brake Assist System (BAS) – If Equipped The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The BAS detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes.
Page 394: Hill Start Assist (Hsa) - If Equipped
Hill Start Assist (HSA) – If Equipped The HSA system is designed to assist the driver in launching a vehicle on an incline. HSA will maintain the level of brake pressure the driver inputs for a short duration once the driver takes his foot off of the brake pedal.
Page 395 394 STARTING AND OPERATING The system will only work if the intended direction of the vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and the vehicle is in DRIVE and the activation criteria are met, HSA will activate.
Page 396 WARNING! (Continued) • HSA is not a parking brake. If you stop the vehicle on a hill without putting the transmission in PARK or using the parking brake, it will roll down the incline and could cause a collision with an- other vehicle or object.
Page 397: Electronic Stability Control (Esc) - If Equipped
396 STARTING AND OPERATING EVIC Equipped Vehicles HSA is a Customer Programmable Feature on a EVIC equipped vehicle. If you wish to turn off the HSA feature, refer to “Electronic Vehicle Information Center (EVIC)/ Customer Programmable Features” in “Understanding Your Instrument Panel” for further information. Electronic Stability Control (ESC) –...
Page 398 this mode. This mode should be used for almost all driving situations. ESC should only be turned to “Partial Off” or “ESP Off” for specific reasons as noted below. ESC Partial Off This mode is entered by momentarily pressing the “ESC Off”...
Page 399 398 STARTING AND OPERATING All Four-Wheel Drive Vehicles in 4WD AUTO and 4WD LOCK Modes Can Also Choose the Following ESC Operating Mode. This is the Only ESC Operating Mode in 4WD LOW: Full Off This mode is intended for off-road use when ESC stabil- ity features could inhibit vehicle maneuverability due to trail conditions.
Page 400: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
“ESC Off” is the only operating mode for ESC in 4WD LOW. Whenever the vehicle is started in 4WD LOW or the transfer case (if equipped) is shifted from 4WD LOCK or NEUTRAL, to 4WD LOW, the ESC system will be in this mode.
Page 401: Trailer Sway Control (Tsc) - If Equipped
400 STARTING AND OPERATING Malfunction Indicator Light” begins to flash during ac- celeration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. NOTE: • The “ESC Activation/Malfunction Indicator Light” and the “ESC OFF Indicator Light”...
Page 402: Tire Safety Information
TSC is only active in the default “ESC On” mode. TSC can be disabled by pressing the “ESC Off” switch and entering “ESC Partial Off” mode. It is not active in the “ESC Partial Off” or “ESC Off” modes. Refer to the ESC portion of this section for an explanation of the different ESC operating modes.
Page 403 402 STARTING AND OPERATING NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards.
Page 404 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%)
Page 405 404 STARTING AND OPERATING Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 406: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. DOT = Department of Transportation —...
Page 407: Tire Terminology And Definitions
406 STARTING AND OPERATING Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof.
Page 408: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire Placard Location STARTING AND OPERATING 407 Tire and Loading Information Placard Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle...
Page 409 408 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading”...
Page 410 available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
Page 411 410 STARTING AND OPERATING...
Page 412: Tires - General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 413: Tire Inflation Pressures
412 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure.
Page 414: Tire Pressures For High Speed Operation
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 415: Radial Ply Tires
414 STARTING AND OPERATING loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous.
Page 416: Tire Spinning
original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity.
Page 417: Tread Wear Indicators
416 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves.
Page 418: Replacement Tires
Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 419: Supplemental Tire Pressure Information - If Equipped
418 STARTING AND OPERATING WARNING! (Continued) • Never use a tire with a smaller load index or capacity other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision.
Page 420 CAUTION! To avoid damage to your vehicle, tires or chains, observe the following precautions: • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Bro- ken chains can cause serious vehicle damage. Stop the vehicle immediately if noise occurs that could suggest chain breakage.
Page 421: Snow Tires
420 STARTING AND OPERATING NOTE: • The use of class “S” chains is permitted with P245/ 70R17 tires only. • The use of class “U” chains is permitted on the front and rear of 4X4, 2500 model trucks with LT245/ 70R17E tires.
Page 422: Tire Rotation Recommendations
If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h).
Page 423: Directional Tires - If Equipped
422 STARTING AND OPERATING The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire Rotation Directional Tires – If Equipped For the R/T package with 22” tires & wheels, tire rotation must be performed with consideration of the tire rotation direction.
Page 424: Dual Rear Wheels
Dual Rear Wheels Tire Rotation The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. STARTING AND OPERATING 423 CAUTION! 3500 Dual Rear Tires have only one approved direc-...
Page 425: Tire Pressure Monitor System (Tpms)
424 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C).
Page 426 For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (158 kPa).
Page 427: Base System
426 STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure.
Page 428 The matching full size spare wheel and tire assembly (if equipped) has a TPM sensor. The matching full size spare can be used in place of any of the four road tires. The TPMS will only monitor the pressure in the full size spare when it is used in place of a road tire.
Page 429: Premium System - If Equipped
428 STARTING AND OPERATING 3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. Vehicles with Full Size Spare 1. The matching full size spare wheel and tire assembly has a TPM sensor that can be monitored by the TPMS.
Page 430 The matching full size spare wheel and tire assembly (if equipped) has a TPM sensor. The full size spare can be used in place of any of the four road tires. A spare with a pressure below the low-pressure limit will not cause the TPM Telltale Light to illuminate or the chime to sound.
Page 431 430 STARTING AND OPERATING turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS Warning If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid.
Page 432: Tire Pressure Monitor System (Tpms) Tire Light Load Inflation Switch Description (2500 Models) - If Equipped
1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumulation of snow or ice around the wheels or wheel housings.
Page 433 432 STARTING AND OPERATING The TPMS tire light load inflation switch will allow the driver to switch between the max load inflation pressure (cold) low pressure warning threshold and the light load inflation pressure (cold) low pressure warning threshold depending on the vehicle’s load condition. The Tire and Loading Information label defines the recommended front and rear cold tire inflation pressures for the vehicle when operating in the Max Load condition.
Page 434 also equipped to be driven with tire pressures appro- priate to either a Light Load condition or the vehicle Max Load condition. • The tire light load inflation switch will allow the driver to change between the max load inflation pressure (cold) low pressure warning threshold and the light load inflation pressure (cold) low pressure warning threshold depending on the vehicle’s load condition.
Page 435 434 STARTING AND OPERATING Tire Pressure Information label. The Supplemental Tire Pressure Information label is located on the rear face of the driver door opening. Use an accurate tire gauge to check the tire pressures when lowering all four tire pressures.
Page 436: General Information
the max load inflation pressure (cold) values to switch the TPMS system to the max load inflation pressure (cold) low pressure warning threshold. If after pressing the tire light load inflation switch, and tire pressures are below the max load inflation pressure (cold) low pressure warning thresholds, the TPMS low pressure warning telltale light (located in the instrument cluster) will turn ON and a chime will sound.
Page 437: 5.7L Engine
436 STARTING AND OPERATING gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. 5.7L Engine The 5.7L engine is designed to meet all emissions regulations and provide satisfac- tory fuel economy and performance when using high quality unleaded gasoline hav- ing an octane range of 87 to 89.
Page 438: Gasoline/Oxygenate Blends
The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability for the engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as Ethanol. Fuels blended with oxygenates may be used in your vehicle.
Page 439: Mmt In Gasoline
438 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with E-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory More extensive repairs will be required for prolonged exposure to E-85 fuel.
Page 440: Fuel System Cautions
Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine perfor- mance and damage the emission control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
Page 441: Carbon Monoxide Warnings
440 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill.
Page 442: Ethanol Fuel (E85)
E85 Fuel Cap CAUTION! Only vehicles with the E85 fuel filler door label can operate on E85. STARTING AND OPERATING 441 E85 Badge Ethanol Fuel (E85) E85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
Page 443: Fuel Requirements
442 STARTING AND OPERATING WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
Page 444: Selection Of Engine Oil For Flexible Fuel Vehicles (E85) And Gasoline Vehicles
Selection Of Engine Oil For Flexible Fuel Vehicles (E85) and Gasoline Vehicles FFV vehicles operated on E85 require specially formu- lated engine oils. These special requirements are included in MOPAR engine oils, and in equivalent oils meeting Chrysler Specification MS-6395. The manufacturer re- quires engine oils that are API Certified and meet the requirements of Material Standard MS-6395.
Page 445: Maintenance
444 STARTING AND OPERATING Maintenance CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability. ADDING FUEL The fuel filler cap (gas cap) is located behind the fuel filler door, on the left side of the vehicle.
Page 446 CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the “Malfunc- tion Indicator Light (MIL)”...
Page 447: Loose Fuel Filler Cap Message
446 STARTING AND OPERATING Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the EVIC telltale display area. Refer to “Electronic Vehicle Information Center (EVIC) in “Understanding Your Instrument Panel”...
Page 448 Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded. Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).
Page 449: Trailer Towing
448 STARTING AND OPERATING then be determined separately to be sure that the load is properly distributed over the front and rear axle. Weigh- ing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.
Page 450: Common Towing Definitions
Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR.
Page 451 450 STARTING AND OPERATING WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Tongue Weight (TW) The tongue weight is the downward force exerted on the hitch ball by the trailer.
Page 452 safety. The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with GAWR requirements.
Page 453 452 STARTING AND OPERATING EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of Weight- Distributing Hitch (Incorrect) Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed.
Page 454: Trailer Hitch Classification
Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Classification The rear bumper is intended to tow trailers up to 5,000 lbs (2 268 kg) without added equipment or alter- ations to the standard equipment.
Page 455: Trailer Towing Weights (Maximum Trailer Weight Ratings)
• http:// www.dodge.com/bodybuilder. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle.
Page 456: Towing Requirements
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “Tire Safety Information/Tire and Loading In- formation Placard”...
Page 457 456 STARTING AND OPERATING WARNING! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 458 WARNING! (Continued) 2. GTW 3. GAWR 4. Trailer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements –...
Page 459 458 STARTING AND OPERATING actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
Page 460 NOTE: This module has been designed and verified for electric trailer brakes. To determine the type of brakes on your trailer, check with your trailer manufacturer or dealer. 1 — GAIN/Brake Output Power Display 2 — Manual Brake Control Lever 3 —...
Page 461 460 STARTING AND OPERATING lever is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes. The trailer and the vehicle’s brake lamps will come on when either vehicle braking or manual trailer brakes are applied.
Page 462 1. Make sure the trailer brakes are in good working condition, functioning normally, and properly adjusted. See your trailer dealer if necessary. 2. Hook up the trailer and make the electrical connec- tions according to the trailer manufacturer’s instructions. 3. When a trailer with electric brakes is plugged in, the GAIN setting will illuminate.
Page 463 462 STARTING AND OPERATING CAUTION! The ITBM module has been designed and verified for electric trailer brakes. Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in damage to your vehicle, trailer, or other property.
Page 464 Towing Requirements – Trailer Lights and Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package will include a four and seven- pin wiring harness.
Page 465: Towing Tips
464 STARTING AND OPERATING Seven-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 — Left Stop/Turn 3 — Right Stop/Turn 7 — Running Lamps 4 — Electric Brakes WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automo- tive technician.
Page 466 NOTE: Using “TOW/HAUL” mode or a lower gear range while operating the vehicle under heavy operating conditions will improve performance and extend trans- mission life by reducing excessive shifting and heat build up. This action will also provide better engine braking. The automatic transmission fluid and filter should be changed if you regularly tow a trailer for more than 45 minutes of continuous operation.
Page 467: Snowplow
466 STARTING AND OPERATING − Air Conditioning Turn off temporarily. SNOWPLOW 1500 Models Only NOTE: Do not use this model vehicle for snowplow applications. WARNING! Snowplows and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure.
Page 468 NOTE: Before installation of a snowplow it is highly recommended that the owner/installer obtain and follow the recommendations contained within the current Dodge Body Builders Guide. See your authorized dealer, installer or snowplow manufacturer for this information. There are unique electrical systems that must be con- nected to properly assure operator safety and prevent overloading vehicle systems.
Page 469 468 STARTING AND OPERATING Snowplow Prep Package Model Availability For Information about snowplow applications visit www.dodge.com or refer to the current Dodge Body Builders Guide. 1. The maximum number of occupants in the truck should not exceed two. 2. The total GVWR or the Front GAWR or the Rear GAWR should never be exceeded.
Page 470 Over the Road Operation With Snowplow Attached The blade restricts air flow to the radiator and causes the engine to operate at higher than normal temperatures. Therefore, when transporting the plow, angle the blade completely and position it as low as road or surface conditions permit.
Page 471 470 STARTING AND OPERATING General Maintenance Snowplows should be maintained in accordance with the plow manufacturer’s instructions. Keep all snowplow electrical connections and battery terminals clean and free of corrosion. When plowing snow, to avoid transmission and drive- train damage, the following precautions should be ob- served.
Page 472: Recreational Towing (Behind Motorhome, Etc.)
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Flat Tow NONE Front Dolly Tow Rear On Trailer Two-Wheel Drive Four-Wheel Drive Models Models See Instructions • Automatic transmission in PARK • Manual transmission in gear NOT ALLOWED (NOT in NEUTRAL (N) •...
Page 473: Recreational Towing - Two-Wheel Drive Models
472 STARTING AND OPERATING Recreational Towing – Two-Wheel Drive Models DO NOT flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed ONLY if the rear wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer.
Page 474 must be placed in gear (NOT in NEUTRAL) for recre- ational towing. Refer to the following for the proper transfer case NEUTRAL shifting procedure for your vehicle. CAUTION! • Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing.
Page 475 474 STARTING AND OPERATING Shifting Into Neutral (N) – Manual Shift Transfer Case (If Equipped) Use the following procedure to prepare your vehicle for recreational towing. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake.
Page 476 8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with automatic transmission in DRIVE or manual transmission in first gear. 10. Turn OFF the engine. 11.
Page 477 476 STARTING AND OPERATING 6. Shift the transfer case lever to the desired position. NOTE: When shifting out of transfer case Neutral (N), turning the engine OFF may be required to avoid gear clash. 7. Shift the automatic transmission into PARK, or place manual transmission in Neutral.
Page 478 CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop. Shift automatic transmission into PARK. 2.
Page 479 478 STARTING AND OPERATING 14. Shift the transmission into PARK or place manual transmission in gear (not in Neutral). CAUTION! Damage to the transmission may occur if the trans- mission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL, ensure that the engine is OFF prior to shifting the transmission into PARK.
Page 480 Shifting Out of Neutral – Electronic Shift Transfer Case (If Equipped) Use the following procedure to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3.
Page 481 480 STARTING AND OPERATING 15. Shift the transmission into gear, release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally. NOTE: • Steps 1 through 5 are requirements that must be met prior to pressing the transfer case NEUTRAL button and must continue to be met until the shift has been completed.
Page 482: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....482 Jacking And Tire Changing ....482 Jack Location .
Page 483: Hazard Warning Flasher
482 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.
Page 484: Jack Location
Jack Location The jack and jack tools are stored under the front passenger seat. Removal To access the jack and jack tools you must remove the plastic access cover, located on the side of the seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab.
Page 485 484 WHAT TO DO IN EMERGENCIES Jack and Tools (1500 Series) Jack and Tools (2500/3500 Series)
Page 486 WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 487 486 WHAT TO DO IN EMERGENCIES Folding Flap and Rolling Bag Tying Bag to Jack with Straps...
Page 488 WHAT TO DO IN EMERGENCIES 487 Jack and Tools Tied Jack and Tools (1500 Series) 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt.
Page 489: Removing The Spare Tire
488 WHAT TO DO IN EMERGENCIES Jack and Tools (2500/3500 Series) Removing The Spare Tire Remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
Page 490: Preparations
Removing the Spare Tire 1 — Wheel Wrench 2 — Spare Tire It is recommended that you stow the flat or spare to avoid tangling the loose cable. WHAT TO DO IN EMERGENCIES 489 NOTE: The winch mechanism is designed for use with the jack extension tube only.
Page 491: Instructions
490 WHAT TO DO IN EMERGENCIES 4. Place the shift lever into PARK. On four-wheel drive vehicles, shift the transfer case to the 4L position. 5. Turn the ignition OFF. 6. Block both the front and rear of the wheel diagonally opposite the jacking position.
Page 492 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change.
Page 493 492 WHAT TO DO IN EMERGENCIES 4X4 Jacking Location 4X2 Jacking Location Operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required.
Page 494 For 4x2 and 4x4 trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between the wheel and the shock bracket with the drive tubes extending to the rear.
Page 495 494 WHAT TO DO IN EMERGENCIES 4x2 Jacking Location Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required. For 2500/3500 4x4 series trucks, when changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
Page 496 drive tube to the extension tube. Place the jack under the axle between the spring and the shock absorber with the drive tubes extending to the rear. Rear Jacking Location (All) Connect the jack tube extension and wheel wrench. WHAT TO DO IN EMERGENCIES 495 CAUTION! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts...
Page 497 496 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel off. On single rear-wheel (SRW) trucks, install the spare wheel and wheel nuts with the cone shaped end of the wheel nuts toward the wheel. On 3500 dual rear-wheel models (DRW) the wheel nuts are a two-piece assembly with a flat face.
Page 498: Hub Caps/Wheel Covers - If Equipped
Hub Caps/Wheel Covers — If Equipped The hub caps must be removed before raising the vehicle off the ground. For 2500/3500 single rear-wheel (SRW) models, use the blade on the end of the lug wrench to pry the hub cap off. Insert the blade end into the pry-off notch and carefully pop off the hub cap with a back-and-forth motion.
Page 499: Wheel Nuts
498 WHAT TO DO IN EMERGENCIES nut bolt circle and strike the high side down with a rubber mallet. Be sure that the hub caps and wheel skins are firmly seated around the wheel. Wheel Nuts All wheel nuts should be tightened occasionally to elimi- nate the possibility of wheel studs being sheared or the bolt holes in the wheels becoming elongated.
Page 500 Oiling Location Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assem- bling the wheels for best access to the tire valve on the inner wheel. The tires of both dual wheels must be completely off the ground when tightening, to ensure wheel centering and maximum wheel clamping.
Page 501: To Stow The Flat Or Spare
500 WHAT TO DO IN EMERGENCIES These dual rear wheels should be tightened as follows: Tightening Pattern 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table.
Page 502: Hoisting
WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immedi- ately. Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening.
Page 503: Preparations For Jump-Start
502 WHAT TO DO IN EMERGENCIES NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.
Page 504: Jump-Starting Procedure
WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
Page 505 504 WHAT TO DO IN EMERGENCIES CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle.
Page 506: Freeing A Stuck Vehicle
8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicle you should have the battery and charging system in- spected at your authorized dealer.
Page 507 506 WHAT TO DO IN EMERGENCIES Allow the engine to idle with the transmission shift lever in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during pro- longed efforts to free a stuck vehicle.
Page 508: Emergency Tow Hooks - If Equipped
EMERGENCY TOW HOOKS — IF EQUIPPED Your vehicle may be equipped with emergency tow hooks. NOTE: For off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle. WARNING! •...
Page 509: Towing A Disabled Vehicle
508 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the transmission and drivetrain are operable, disabled vehicles may also be towed as described under “Recreational Towing”...
Page 510: Towing Without The Ignition Key Fob
Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets.
Page 511: Two-Wheel Drive Models
510 WHAT TO DO IN EMERGENCIES Two-Wheel Drive Models The manufacturer recommends towing your vehicle with all four wheels OFF the ground using a flatbed. If flatbed equipment is not available, and the transmis- sion is operable, the vehicle may be towed (with rear wheels on the ground) with the transmission in NEU- TRAL.
Page 512 CAUTION! • Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing. • Failure to follow these towing methods could result in damage to the transmission and/or trans- fer case.
Page 514 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 3.7L ... . . 516 Engine Compartment — 4.7L ... . . 517 Engine Compartment —...
Page 515 514 MAINTAINING YOUR VEHICLE Body Lubrication ....529 Windshield Wiper Blades ....530 Adding Washer Fluid .
Page 516 Fluid Capacities ..... . 569 Fluids, Lubricants And Genuine Parts ..571 MAINTAINING YOUR VEHICLE 515 Engine .
Page 517: Engine Compartment - 3.7L
516 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.7L 1 — Air Cleaner Filter 2 — Automatic Transmission Dipstick (If Equipped) 3 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 5 — Battery 6 — Integrated Power Module 7 — Washer Fluid Reservoir 8 —...
Page 518: Engine Compartment - 4.7L
ENGINE COMPARTMENT — 4.7L 1 — Air Cleaner Filter 2 — Automatic Transmission Dipstick 3 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 5 — Battery 6 — Integrated Power Module MAINTAINING YOUR VEHICLE 517 7 — Washer Fluid Reservoir 8 —...
Page 519: Engine Compartment - 5.7L
518 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.7L 1 — Air Cleaner Filter 2 — Automatic Transmission Dipstick 3 — Engine Oil Fill 4 — Engine Oil Dipstick 5 — Brake Fluid Reservoir 6 — Battery 7 — Washer Fluid Reservoir 8 —...
Page 520: Onboard Diagnostic System (Obd Ii)
ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 521: Emissions Inspection And Maintenance Programs
520 MAINTAINING YOUR VEHICLE the SELECT button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass...
Page 522: Replacement Parts
4. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
Page 523: Dealer Service
522 MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself.
Page 524: Engine Oil
CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air condi- tioning.
Page 525 524 MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, whichever occurs first. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395.
Page 526: Engine Oil Filter
Lubricants which do not have both the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. NOTE: For 2500/3500 trucks with a 5.7L engine oper- ating under a gross combined weight rating of 14,000 lbs (6 350 kg) or greater, SAE 5W-30 engine oil is recom- mended for all operating temperatures.
Page 527: Engine Air Cleaner Filter
526 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Refer to “Maintenance Schedule” for further information. WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance.
Page 528 WARNING! (Continued) • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other. •...
Page 529: Air Conditioner Maintenance
528 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test.
Page 530: Front Driveshaft Lubrication - 2500/3500
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluoro- carbon (HFC) that is endorsed by the Environmental Protection Agency (EPA) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment.
Page 531: Windshield Wiper Blades
530 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
Page 532: Exhaust System
The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
Page 533 532 MAINTAINING YOUR VEHICLE WARNING! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle”...
Page 534 Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
Page 535: Cooling System
534 MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.
Page 536 Refer to “Maintenance Schedule” for further information. Selection Of Coolant Use only the manufacturer’s recommended engine cool- ant (antifreeze). Refer to “Fluids, Lubricants, and Genu- ine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection.
Page 537 536 MAINTAINING YOUR VEHICLE replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze).
Page 538 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
Page 539 538 MAINTAINING YOUR VEHICLE of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle.
Page 540: Brake System
• Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat.
Page 541 540 MAINTAINING YOUR VEHICLE The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a “MAX” dot and an “MIN” dot. The fluid level must be kept within these two dots. Do not add fluid above the MAX mark because leakage may occur at the cap.
Page 542: Rear Axle And 4X4 Front Driving Axle Fluid Level
WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point.
Page 543: Transfer Case
542 MAINTAINING YOUR VEHICLE This inspection should be made with the vehicle in a level position. The fluid level should be even with the bottom of the fill hole for the manufacturer’s C205F HD front axles. The fluid level should be 5/8 in (16 mm) below the fill hole on 9 1/4 in manufacturer’s rear axles.
Page 544: Automatic Transmission
Lubricant Selection Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Fluid Level Check This fluid level can be checked by removing the filler plug. The fluid level should be to the bottom edge of the filler plug hole with the vehicle in a level position.
Page 545 544 MAINTAINING YOUR VEHICLE Fluid Level Check If equipped with a dipstick, use the following procedure. If your vehicle has a capped dipstick tube, it is sealed and should not be tampered with. Your authorized dealer has the proper tools to ensure that the fluid level is set properly.
Page 546 required into the dipstick tube. Do not overfill. After adding any quantity of oil through the oil fill tube, wait a minimum of two minutes for the oil to fully drain into the transmission before rechecking the fluid level. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD”...
Page 547: Appearance Care And Protection From Corrosion
546 MAINTAINING YOUR VEHICLE It is important that proper lubricant is used in the transmission. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supple- mental additives.
Page 548 • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR Car Wash or equiva- lent, or a mild car wash soap and rinse the panels completely with clear water.
Page 549 548 MAINTAINING YOUR VEHICLE • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately.
Page 550 Stain Repel Fabric Cleaning Procedure – If Equipped Stain Repel seats may be cleaned in the following man- ner: • Remove as much of the stain as possible by blotting with a clean, dry towel. • Blot any remaining stain with a clean, damp towel. •...
Page 551 550 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning Headlights Your vehicle is equipped with plastic headlights and fog lights (if equipped) that are lighter and less susceptible to stone breakage than glass headlights.
Page 552 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
Page 553: Fuses
552 MAINTAINING YOUR VEHICLE 2. Mix a mild soap or detergent with water with a soft cloth or brush. 3. Rinse bedliner with water. 4. Once dry, apply a small amount of MOPAR Spray-On Bedliner Conditioner to a moist towel or sponge and wipe over the entire surface of the truck bedliner.
Page 554 cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart. Totally Integrated Power Module (TIPM) MAINTAINING YOUR VEHICLE 553 Cavity Cartridge Mini Fuse Fuse 40 Amp Trailer Tow Green 30 Amp Electric Brake Pink 30 Amp...
Page 555 554 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 40 Amp Green 30 Amp Pink 60 Amp Yellow 20 Amp Blue 30 Amp Pink 40 Amp Green Description Cavity Cartridge Power Seat Drivetrain Control Module Streaming Video Module/Video Sys- tem 3 Module/Video System 2 Module/ DISP/DVD Trailer Tow Lamps/...
Page 556 Cavity Cartridge Mini Fuse Fuse 20 Amp Power Outlet #1 (Ci- Yellow gar Lighter)/Rain Snsr 20 Amp Power Outlet #2 Yellow 20 Amp Front Heated Seat & Yellow Steering Wheel 20 Amp Rear Heated Seats Yellow 20 Amp Hands Free Module/ Yellow Vanity Lamp/ Universal Garage...
Page 557 556 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 25 Amp Natural 15 Amp Blue 20 Amp Yellow 10 Amp 10 Amp 20 Amp Yellow 10 Amp Description Cavity Cartridge Automatic Shutdown 1 and 2 Instrument Cluster Interior Lighting /Sw Steering Wheel/Sw Bank Automatic Shutdown...
Page 558 Cavity Cartridge Mini Fuse Fuse 15 Amp LH Front & Rear Blue Parklamps 20 Amp Power Outlet Yellow 10 Amp Antilock Brakes/ Stability Control Sys- tem Module/ Stoplamp Switch 25 Amp All Door Lock &Un- Natural lock Description • When installing the totally integrated power mod- ule cover, it is important to ensure the cover is properly positioned and fully latched.
Page 559: Vehicle Storage
558 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw (IOD) fuse located in the Integrated Power Module, located in the engine compartment.
Page 560: Replacement Bulbs
REPLACEMENT BULBS LIGHT BULBS – Interior Overhead Console Lamps ....TS 212-2 Dome Lamp ......7679 NOTE: For lighted switches, see your authorized dealer for replacement instructions.
Page 561 560 MAINTAINING YOUR VEHICLE 4. Remove the two plastic push-in rivets that secure the upper radiator seal to the radiator. 5. Remove the upper radiator seal from the vehicle. 6. Remove the two headlamp assembly attachment screws. 7. Reach into the front wheel house ahead of the front wheel, remove the fastener, and lift the cover over the access hole in the front of the wheel house splash shield.
Page 562 9. Remove the headlamp assembly. Grasp the outboard edge of the lamp and pull it straight forward to disen- gage the ball stud from the plastic grommet. MAINTAINING YOUR VEHICLE 561 10. Disconnect the wiring harness connectors from the bulb socket. 11.
Page 563: Fog Lamps
562 MAINTAINING YOUR VEHICLE Fog Lamps 1. Reach under and behind the front bumper to access the back of the front fog lamp housing. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise bulb from the housing.
Page 564 2. Pull the outboard side of the lamp rearward far enough to unsnap the two receptacles on the outboard side of the lamp housing from the two plastic snap post retainers in the outer box side panel. MAINTAINING YOUR VEHICLE 563 3.
Page 565: Center High-Mounted Stoplamp (Chmsl) With Cargo Lamp
564 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplamp (CHMSL) With Cargo Lamp 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket socket and bulb from housing.
Page 566: Cab Top Clearance Lamps - If Equipped
CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • Outside Bulbs: Cargo Lamps MAINTAINING YOUR VEHICLE 565 • Inside Bulb: Center High-Mounted Stop Lamp 5.
Page 567 566 MAINTAINING YOUR VEHICLE 2. Rotate the socket ⁄ turn and pull it from the lamp 3. Pull the bulb straight from it’s socket and replace. assembly.
Page 568: Rear Lamp Bar Id Marker (Dual Rear Wheels) - If Equipped
Rear Lamp Bar ID Marker (Dual Rear Wheels) — If Equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. MAINTAINING YOUR VEHICLE 567 2. Turn the socket ⁄ turn counterclockwise to access the bulb.
Page 569: Side Marker Lamps (Dual Rear Wheels) - If Equipped
568 MAINTAINING YOUR VEHICLE Side Marker Lamps (Dual Rear Wheels) — If Equipped 1. Push rearward on the side marker lamp assembly. 2. Pull the entire assembly from the fender. 3. Turn the socket ⁄ turn counterclockwise and remove from assembly to access the bulb. 4.
Page 570: Fluid Capacities
FLUID CAPACITIES Fuel (Approximate) 1500 Regular Cab Shortbed/Crew Quad Cab Models 1500 Regular Cab Longbed/Crew Quad Cab Models (Optional) 2500/3500 Shortbed Models 2500/3500 Longbed Models Engine Oil with Filter 3.7L Engine (SAE 5W-20, API Certified) 4.7L Engine (SAE 5W-20, API Certified) 5.7L Engine (SAE 5W-20, API Certified) 5.7L Engine (SAE 5W-30, API Certified).
Page 571 570 MAINTAINING YOUR VEHICLE Cooling System 3.7L Engine (MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 4.7L Engine (MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 5.7L Engine — 1500 Models (MOPAR Antifreeze/ Coolant 5 Year/100,000 Mile Formula or equivalent) 5.7L Engine —...
Page 572: Engine
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil – For 2500/3500 trucks operat- ing under a gross combined weight rating greater than 14,000 lbs/(6,350 kg.) Engine Oil Filter Spark Plugs – 3.7L Engine Spark Plugs – 4.7L Engine Spark Plugs –...
Page 573: Chassis
572 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Transfer Case – NVG 246 Only Front Axle – 1500 Four-Wheel Drive Models Rear Axle – 1500 Models Front and Rear Axle – 2500/3500 Models Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product.
Page 574 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..574 Maintenance Schedule ....574 Required Maintenance Intervals ..576...
Page 575 574 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability.
Page 576 NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated.
Page 577 576 MAINTENANCE SCHEDULES • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of the coolant reservoir, brake master cylinder, and transmission and add as needed. • Check all lights and other electrical items for correct operation.
Page 578 8,000 Miles (13,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). ❏...
Page 579: Service Schedule
578 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏...
Page 580 40,000 Miles (65,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). ❏...
Page 581 580 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). ❏...
Page 582 64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏...
Page 583 582 MAINTENANCE SCHEDULES 72,000 Miles (117,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏...
Page 584 88,000 Miles (143,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). ❏...
Page 585 584 MAINTENANCE SCHEDULES 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏...
Page 586 104,000 Miles (169,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏...
Page 587 586 MAINTENANCE SCHEDULES 120,000 Miles (195,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏...
Page 588 128,000 Miles (208,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏...
Page 589 588 MAINTENANCE SCHEDULES 144,000 Miles (234,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏...
Page 590 † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
Page 592: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......593 Prepare For The Appointment .
Page 593 592 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....597 Department Of Transportation Uniform Tire Quality Grades ......598 Treadwear .
Page 594: Suggestions For Obtaining Service For Your Vehicle
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
Page 595: Chrysler Group Llc Customer Center
594 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Page 596: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 597: Warranty Information
596 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience.
Page 598: In Canada
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer.
Page 599: Department Of Transportation Uniform Tire
598 IF YOU NEED CONSUMER ASSISTANCE LLC vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
Page 600: Traction Grades
in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Federal safety requirements in addition to these grades. Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Page 601 600 IF YOU NEED CONSUMER ASSISTANCE grade C corresponds to a level of performance, which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum required by law.
Page 602 INDEX...
Page 603 602 INDEX Adding Engine Coolant (Antifreeze) ..535 Adding Fuel ......444 Adjustable Pedals .
Page 604 Fluid Level Check ....543,544 Fluid Type ......543,572 Gear Ranges .
Page 605 604 INDEX Power Steering ......386 Radiator (Coolant Pressure) ....536 Car Washes .
Page 606 Coolant Level ..... . 534,537 Disposal of Used Coolant ....537 Drain, Flush, and Refill .
Page 607 606 INDEX Electrical Power Outlets ....160 Electronic Brake Control System ... . . 390 Anti-Lock Brake System .
Page 608 Exhaust Gas Caution ....83,440 Exhaust System ..... . . 83,531 Exterior Lighting .
Page 609 608 INDEX Filler Cap (Gas Cap) ....446 Gauge ......206 Light .
Page 610 Hazard Driving Through Flowing, Rising, or Shallow Standing Water ....362 Hazard Warning Flasher ....482 Head Restraints .
Page 611 610 INDEX Integrated Power Module (Fuses) ... . 552 Integrated Trailer Brake Controls ... . . 458 Interior Appearance Care ....549 Interior Lights .
Page 612 Center Mounted Stop ....564 Check Engine (Malfunction Indicator) ..219 Courtesy/Reading ..... 149 Daytime Running .
Page 613 612 INDEX Lower Anchors and Tether for CHildren (LATCH) ......73 Lubrication, Body .
Page 614 Odometer ......210,211 Trip ......210,211 Off-Pavement Driving (Off-Road) .
Page 615 614 INDEX Phone, Cellular ......100 Phone, Hands-Free (Uconnect™) ... . . 100 Pickup Box .
Page 616 Reformulated Gasoline ....436 Refrigerant ......529 Reminder, Seat Belt .
Page 617 616 INDEX Seats ......100,109 Adjustment ......100 Child .
Page 618 Speedometer ......207 Starting ......25,305 Automatic Transmission .
Page 619 618 INDEX High Speed ......413 Inflation Pressures ..... 412 Life of Tires .
Page 620 Transmission ......311 Automatic ..... . 311,316,543 Fluid .
Page 621 620 INDEX Washing Vehicle ......547 Water Driving Through ..... . 362 Wheel and Wheel Trim .
Page 622 Chrysler Group LLC 11D241-126-AB Second Edition Printed in U.S.A.

This manual is also suitable for:

3500 2011 Ram truck 2500 2011 Ram truck3500 2011 2500 2011

RAM 2011 1500 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for RAM 2011 Ram 1500

Summary of Contents for RAM 2011 Ram 1500