NEC Express5800/R120g-1E Maintenance Manual page 110

Chapter 2 Useful Features
Item
IPv6 Property
IPv6
Address Assignment
Mode
Link Local Address
Global Address
Static Address
Prefix Length
Gateway Address
Access Limitation
Limitation Type
IP Address
Service
HTTPS
HTTPS Port Number
HTTP
HTTP Port Number
SSH
SSH Port Number
*1: Can be specified if the server supports this feature.
*2: When set to "Shared BMC LAN", the BMC LAN port is disabled. When set to "Shared BMC LAN", the system (OS) LAN port
also transmits or receives data. Thus, the network performance may be reduced due to load of system LAN (or BMC LAN).
*3: If an illegal value is specified for subnet mask, an error message is displayed and setting is disabled.
*4: Can be changed only when DHCP is set to "Disable".
*5: Can be changed only when DHCP is set to "Enable".
*6: Host Name should be within 63 characters.
Acceptable characters are: alphanumeric, hyphen (-), underscore (_), and period (.).
*7: Host Name and Domain Name should be within total of 255 characters.
Acceptable characters are: alphanumeric, hyphen (-), underscore (_), and period (.).
*8: The range of IP address to "Allow" or "Deny" access is delimited by ",(Comma)". With regard to the setting of "Deny" access,
"*(Asterisk)" can be described as a wild-card. (ex: 192.168.1.*,192.168.2.1,192.168.2.254)
*9: Can be specified when Access Limitation Type is "Allowed Address" or "Deny Address". The length must not exceed 255
characters.
*10: If HTTP is set to "Enable", HTTPS is changed to "Enable" automatically. You are not allowed to set "Enable" to HTTP only.
*11: Port number can be specified only when the relevant port is set to "Enable". The port number must be unique.
*12: Can be specified only when IPv6 is set to "Enable".
*13: Displayed only when "Dynamic" is specified for Address Assignment Mode.
*14: When following both settings are done, Server Configuration Utility fails to change "Connection Type" in Network Property of
EXPRESSSCOPE Engine 3 configuration.
– "Management LAN" configuration of EXPRESSSCOPE Engine 3 is set to "Shared BMC LAN".
– "Boot Mode" configuration of BIOS SETUP is set to "UEFI".
You can change the configuration of "Connection Type" is available when "Boot Mode" is "Legacy".
Change "Boot Mode" configuration from "UEFI" to "Legacy" before changing "Connection Type" configuration, and then
restore "Boot Mode" to "UEFI" (after changing "Connection Type").
110
Enable or disable IPv6.
Specify the mode to assign IPv6 address (Static or Dynamic).
*12
Display link local address.
Display IPv6 address when Dynamic is specified for assignment mode.
Specify IPv6 address when Static is specified for assignment mode.
Specify the prefix length when Static is specified for assignment mode.
Specify the gateway address when Static is specified for assignment mode.
Select the Access Limitation Type.
Allow All
: Access to BMC is not limited.
Allow Address
: Specify the IP Address that is allowed to access BMC.
Deny Address
: Specify the IP Address that deny to access BMC.
Specify the IP Address (IPv4) to allow or deny to access with BMC.
Enable or disable HTTPS service.
Specify the HTTPS port number.
Enable or disable HTTP service.
*11
Specify the HTTP port number.
Enable or disable SSH service.
*11
Specify the SSH port number.
Express5800/R120g-1E Maintenance Guide
Description
*12
*10
*11
*10
2. Server Configuration
(2/2)
Default Value
Disable
Dynamic
–
*12 *13
–
*12
0::0
*12
64
*12
0::0
Allow All
*8 *9
Blank
Enable
443
Enable
80
Enable
22