Table of Contents
Advertisement
KPP 14-1
block diagram 14-1
configuration 14-6
low-power modes and 8-6
matrix construction 14-6
matrix scanning 14-6
multiple key closures 14-8
operation 14-6
programming model 14-2, C-13
signals 14-2
standby 14-7
KPSR 14-3, C-14
KRDD bits 14-5, C-15
KRE bits 14-3, C-14
KRIE bit 14-4, C-14
–L–
Level-sensitive interrupts 13-2, C-27
Link register 2-3
Load and store 2-2
LOAD bit 15-4, C-24
Load PWMPR and PWMWR bit 15-4, C-24
LOOP bit 11-15, C-44
LOOP IR bit 11-15, C-44
Loop TX and RX for IR Test bit 11-15, C-44
Loop TX and RX for Test bit 11-15, C-44
Loopback bit 12-8, C-33
LOW_REFCLK 8-1
Low-power modes 8-1, 8-4
ISPI operation in 12-11
peripheral behavior 8-5
PWM operation in 15-8
UART operation in 11-23
Low-voltage reset 4-5, 8-6
LPBK bit 12-8, C-33
LPMD (CPU) signals 8-4
LVRSTIN bit 9-4, C-6
LVRSTIN signal 4-5, 8-6
–M–
M•CORE 2-1
architecture 2-2
bus interface 2-8
data format 2-5
instruction set 2-6
operand addressing 2-6
programming model 2-3
MAL 16-13, C-51
Manual mode 12-2, 12-9
Master in, slave out 12-3
Master Mode bit 12-6, C-32
Master out, slave in 12-4
Maximum ratings A-1
MBCA 16-14, C-51
MBCB 16-14, C-51
MBO bit 16-11, C-50
Memory
MOTOROLA
I-4
All manuals and user guides at all-guides.com
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Address Latch 16-13, C-51
Breakpoint 16-12
B, A Control bits 16-10, C-49
B, A Range Control bits 16-10, C-49
Counters 16-14, C-51
Occurrence bit 16-11, C-50
load and store 2-2
map
MMC2001 3-1
peripheral modules 3-2, C-1
organization 2-5
MFCR instruction 2-4
MMC2001
memory
map 3-1
signals 4-1
MOD
timing specifications A-2
MOD signal 4-4, 7-2, 7-6
MODE bit 15-5, C-24
Modules
address map 3-2, C-1
interface operation 3-2
Move from Control Register 2-4
Move to Control Register 2-4
MSTR bit 12-6, C-32
MTCR instruction 2-4
Multiply 2-2
–N–
NIER 10-3, C-2
NIPND 10-4, C-4
Normal Interrupt
Enable Register 10-3, C-2
Pending Flags 10-4, C-4
Pending Register 10-4, C-4
NP flags 10-4, C-4
–O–
OCMR 16-6, C-46
OCR 16-8, C-47
ODEC 16-12
OE Assert bit 7-10, C-19
OE signal 4-4, 7-2
OEA bit 7-10, C-19
OnCE 16-1
block diagram 16-1
Command Register 16-6, C-46
commands 16-21
Control Register 16-8, C-47
controller 16-2, 16-5
debug output 16-6
decoder 16-12
interface signals 16-5
operation 16-1
serial interface 16-5
signals 16-3
MMC2001
REFERENCE MANUAL
Advertisement
Table of Contents
