Daikin EPRA10EAV3 Installer's Reference Manual page 299

Field settings table
Breadcrumb Field code Setting name
9.I [7-09] --
9.I [7-0A] Additional zone fixed pump PWM, in case a bizone kit is installed.
9.I [7-0B] Main zone fixed pump PWM, in case a bizone kit is installed.
9.I [7-0C]
Time needed by the mixing valve to turn from one side to the other, in case a bizone
kit is installed.
9.I [7-0D]
Hysteresis value used to control the tank bivalent in case it's supporting space
heating operation
9.I [7-0E] Offset on the setpoint to determine when the tank is high enough to go the excess
state
9.I [8-00] Minimum running time for domestic hot water operation.
9.I [8-01] Maximum running time for domestic hot water operation.
9.I [8-02] Anti-recycling time.
9.I [8-03] Booster heater delay timer.
9.I [8-04] Additional running time for the maximum running time.
9.I [8-05] Allow modulation of the LWT to control the room temp?
9.I [8-06] Leaving water temperature maximum modulation.
9.I [8-07]
What is the desired comfort main LWT in cooling?
9.I [8-08]
What is the desired eco main LWT in cooling?
9.I [8-09] What is the desired comfort main LWT in heating?
9.I [8-0A] What is the desired eco main LWT in heating?
9.I [8-0B] --
9.I [8-0C] --
9.I [8-0D]
--
9.I [9-00] What is the maximum desired LWT for main zone in heating?
9.I [9-01] What is the mimimum desired LWT for main zone in heating?
9.I [9-02] What is the maximum desired LWT for main zone in cooling?
9.I [9-03]
What is the mimimum desired LWT for main zone in cooling?
9.I [9-04]
Leaving water temperature overshoot temperature.
9.I [9-05] What is the mimimum desired LWT for add. zone in heating?
9.I [9-06] What is the maximum desired LWT for add. zone in heating?
9.I [9-07] What is the mimimum desired LWT for add. zone in cooling?
9.I [9-08] What is the maximum desired LWT for add. zone in cooling?
9.I [9-09] What is the allowed LWT undershoot during cooling start-up?
9.I [9-0A]
What is the room buffering temperature in heating?
9.I [9-0B]
What is the room buffering temperature in Cooling?
9.I [9-0C] Room temperature hysteresis.
9.I [9-0D] Pump speed limitation
9.I [9-0E] --
9.I [C-00]
Domestic heating water priority.
9.I [C-01]
--
9.I [C-02] Is an external backup heat source connected?
9.I [C-03] Bivalent activation temperature.
9.I [C-04]
Bivalent hysteresis temperature.
9.I [C-05]
What is the thermo request contact type for the main zone?
9.I [C-06] What is the thermo request contact type for the add. zone?
(*1) 300 Tank_(*2) 500 Tank_
(*3) *X*_(*4) *H*_(*5) *B*_
(*6) EKECBUA3V_(*7) EKECBUA6V_(*8) EKECBUA9W_
(*9) BUH less
Range, step
Default value
20
R/W
20~95%, step 5%
95%
R/W
20~95%, step 5%
95%
R/W 20~300 seconds, step 5 sec
125 seconds
R/W 2~20, step 0,5 °C
4 °C
R/W 2~22, step 0,5 °C
7 °C
R/O 0~20 min, step 1 min
1 min
R/W 5~95 min, step: 5 min
30 min
R/W 0~10 hour, step: 0,5 hour
0,5 hour
R/W 20~95 min, step: 5 min
50 min
R/W 0~95 min, step: 5 min
95 min
R/W
0: No
1: Yes
R/W 0~10°C, step: 1°C
5°C
R/W [9-03]~[9-02], step: 1°C
18°C
R/W [9-03]~[9-02], step: 1°C
20°C
R/W [9-01]~[9-00], step: 1°C
35°C
R/W [9-01]~[9-00], step: 1°C
33°C
13
10
16
[2-0C]≠2: [2-0C]=2:
R/W 37~65, step: 1°C
[2-0C]=2: 65°C
R/O [2-0C]≠2:
37~55, step: 1°C
55°C
R/W 15~37°C, step: 1°C
25°C
R/W 18~22°C, step: 1°C
22°C
R/W 5~18°C, step: 1°C
7°C
R/W 1~4°C, step: 1°C
2°C
R/W 15~37°C, step: 1°C
25°C
[2-0C]≠2: [2-0C]=2:
R/W 37~65, step: 1°C
[2-0C]=2: 65°C
R/O
[2-0C]≠2:
37~55, step: 1°C
55°C
R/W 5~18°C, step: 1°C
7°C
R/W 18~22°C, step: 1°C
22°C
R/W 1~18°C, step: 1°C
18°C
R/W [3-07]～[3-06]°C, step: 0,5°C
23°C
R/W [3-09]～[3-08]°C, step: 0,5°C
23°C
R/W 1~6°C, step: 0,5°C
1 °C
R/W 0~8, step:1
0: No limitation
1~4: 90~60% pump speed
5~8: 90~60% pump speed during
sampling
6 80% pump speed during sampling
6
R/W 0: Solar priority
1: Heat pump priority
0
R/W 0 none
1 bivalent through header
2 tank DHW bivalent (*5)
3 tank heating + DHW bivalent
R/W -25~25°C, step: 1°C
0°C
R/W 2~10°C, step 1°C
3°C
R/W 0: MMI requests (incl. quick logic)
1: 1 contact
2: 2 contacts
R/W 0: MMI requests (incl. quick logic)
1: 1 contact
2: 2 contacts
11/13
Installer setting at variance with
default value
Date Value
4P670987-1A - 2022.02