Table of Contents
Advertisement
Command Number 238: Zone No. Assignment to Input No. 3 of Expander Module
No. 3
Default values -------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
Command Number 239: Zone No. Assignment to Input No. 4 of Expander Module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 240: Zone No. Assignment to Input No. 5 of Expander Module
No. 3
Default values-------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 241: Zone No. Assignment to Input No. 6 of Expander Module
No. 3
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 242: Zone No. Assignment to Input No. 7 of Expander Module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions-------------------------------------------------------------------------------------> (1)
Command Number 242: Zone No. Assignment to Input No. 7 of Expander Module
No. 3
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 244: Auxiliary Failure Counter
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Auxiliary Fault Counter.
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note: If you program 00 the equipment will not monitor the fault
Command Number 245: Auxiliary Fault Counter BUS-D485
Default values -------------------------------------------------------------------------------> 0
Positions-------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Battery Fault Counter BUS-D485
The code must be 2 digits long. Valid values are 00 to 16.
Note: If you program 00 the equipment will not monitor the Fault.
Command Number 246: Battery Failure Counter
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Posición de dígito (1)- (2): Battery Fault Counter
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note: If you program 00 the equipment will not monitor the fault.
Command Number 247: Siren Fault Counter
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Siren Fault Counter
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note: If you program 00 the equipment will not monitor the fault.
Command Number 249: Fault Counter Expansion Modules Default
Default values ---------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
0
2
3
8
Digit position (1)- (2): Counter Fault Expander modules
The code must be 2 digits long. Valid values are 00 up to 16 events.
(2)
Note: If you program 00 the equipment will not monitor faults.
Command Number 250: Auxiliary Source Fault Counter (Supervisory, Mains and
Low Battery Fault)
0
Default values--------------------------------------------------------------------------------> 0
2
3
9
(2)
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Fault Counter Auxiliary source
The code must be 2 digits long. Valid values are 00 up to 16 events.
0
Note: If you program 00 the equipment will not monitor faults.
2
4
0
Note: The programmed value is valid for Supervisory, Mains and Low Battery
faults.
(2)
Command Number 252: IP-500 Module Fault Counter
Default values -------------------------------------------------------------------------------> 0
0
2
4
1
Positions -------------------------------------------------------------------------------------> (1)
(2)
Digit position (1)- (2): IP-500 Module Fault Counter
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note: If you program 00 the equipment will not monitor the fault.
0
2
4
2
Command Number 253: Network Fault Counter
Default values -------------------------------------------------------------------------------> 0
(2)
Positions -------------------------------------------------------------------------------------> (1)
0
Digit position (1)- (2): Counter Mains Failure
2
4
3
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note: If you program 00 the equipment will not monitor the fault.
(2)
Command Number 254: Alarm Counter in Zones
Default values ------------------------------------------------------------------------------> 0
8
2
4
4
Positions -------------------------------------------------------------------------------------> (1)
(2)
Digit position (1)- (2): Alarm Counter in Zones
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note: If you program 00 the equipment will not supervise the fault.
Command Number 256: Mobile Data Module Failure Counter (3G-COM-G /
4G-MAX-G)
8
Default values-------------------------------------------------------------------------------> 0
2
4
5
(2)
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Counter Mobile Data Module Fault
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note: If you program 00 the equipment will not monitor the fault.
Command Number 259: Tamper Alarms Counter
8
Default values ------------------------------------------------------------------------------> 0
2
4
6
(2)
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Tamper Alarm Counter
The code must be 2 digits long. Valid values are 00 up to 16 events.
Note: If you program 00 the equipment will not monitor the fault.
8
2
4
7
(2)
8
2
4
9
(2)
8
2
5
0
(2)
8
2
5
2
(2)
8
2
5
3
(2)
8
2
5
4
(2)
8
2
5
5
(2)
8
2
5
6
(2)
23
Advertisement
Table of Contents
