Table of Contents
Advertisement
6.1 How to twin a wireless sensor
To twin a sensor, the following steps must be carried out:
1) Be sure to remove the battery from the sensor.
2) Press the [
] key on the keypad.
3) Select [7] RF Disp.
4) Enter the installer code.
5) Choose option [1] Grab Sensor.
6) Indicate the memory location where you want to record the device.
The positions
The available memory slots are 01-24.
7) The keypad will indicate that it is searching for the sensor.
8) Insert the battery into the sensor. Remember to check for correct polarity.
9) Wait for the keypad to confirm that the sensor has been successfully engraved.
and then press the [
].
10) If you wish to continue recording more sensors, repeat the steps from point 6.
Otherwise, press the [#] key to exit the sensor recording option.
6.2 How to pair wireless key fobs
To twin a wireless key fob, the following steps must be carried out:
1) Press the [
] key on the keypad.
2) Select [7] RF Disp.
3) Enter the installer code.
4) Choose option [2] Record. Key Ring.
5) Indicate the memory location where you want to save the key fob. The memory
locations memory available are 01-64.
6) Press and hold any key on the key fob and wait for the keypad to confirm.
your recording. Then press the [
7) If you wish to continue recording more key fobs, repeat the steps from option 5
onwards. If you wish to exit the key fob recording option, press the [
6.3 How to remove wireless sensors
To remove a wireless sensor, the following steps shall be performed:
1) Press the [
] key on the keypad.
2) Select [7] RF Disp.
3) Enter the installer code.
4) Choose option [3] Delete Sens.
5) Indicate the memory location of the sensor to be deleted.
6) Confirm that you really want to delete this sensor by pressing the [1] key.
7) Press the [
] key to accept the deleted sensor confirmation.
8) If you wish to continue deleting more sensors, repeat the steps from point 5.
Otherwise, press the [#] key to exit this option.
6.4 How to remove key rings
To delete a key fob, the following steps must be carried out:
1) Press the [program] key on the keypad.
2) Select [7] RF Disp.
3) Enter the installer code.
4) Choose option [4] Delete Key Fob. Key Ring.
5) Indicate the memory location of the sensor to be deleted.
6) Confirm that you really want to delete this sensor by pressing the [1] key.
7) Press the [
] key to accept the deleted sensor confirmation.
8) If you wish to continue deleting more sensors, repeat the steps from point 5.
Otherwise, press the [#] key to exit this option.
6.5 How to verify the correct operation of a wireless sensor
To be sure that a wireless sensor is working correctly, the panel has a function that
evaluates the level of Signal Strength (RSSI) with which the sensor transmits, in this
way, you will be able to know the signal level with which the signals transmitted
by each wireless sensor enabled in your installation arrive. To evaluate the signal
strength of the wireless sensors, the following steps must be carried out:
1) Press the [program] key on the keypad.
2) Select [7] RF Disp.
3) Enter the installer code.
4) Choose option [5] Test. Sensor.
Each time a sensor generates a transmission, the keypad will indicate the zone
where the sensor is working, the memory location where it is recorded and the
signal level.
6.6 How to display the zones assigned to each sensor
In order to visualise the zones where the different wireless sensors work, the
following steps must be carried out:
1) Press the [program] key on the keypad.
2) Select [7] RF Disp.
3) Enter the installer code.
4) Choose option [6] Zone Assign. Zones.
The keypad will inform you of the memory location where the sensor is stored and
the assigned work zone. To switch to another sensor, use the [
12
] key on the keypad.
] scroll keys.
6.7 How to remove all sensors and/or key fobs
To remove all sensors or keyfobs from your system in one step, the following steps
must be performed:
1) Press the [program] key on the keypad.
2) Select [7] RF Disp.
3) Enter the installer code.
4) Choose option [7] Delete All. All.
5) Choose to delete all sensors by pressing the [1] key or choose to delete all key fobs
by pressing the [2] key.
6) Confirm that you really are sure to delete the selected devices
key and wait for the keypad to indicate that the deletion has been completed.
finished. Press the [
6.8 How to twin a PGM-W/MA-220G module
1) Make sure that the PGM-W module is without 12 V power supply.
2) Press the [
3) Select [7] RF Disp.
4) Enter the installer code.
5) Choose option [8] Record PGM-W.
6) Enter the PGM-W number to be recorded (use the [
number). select the desired PGM-W number). The available PGM-Ws are 1 to 4.
7) The keypad will indicate that it is searching for the device.
8) Power up the PGM-W module, then press the "SINGLE" button located on the
upper left corner of the module.
9) Wait for the keypad to confirm that the PGM-W has been recorded correctly.
and then press the [#] key.
10) If you wish to continue recording other PGM-W modules, repeat the steps from
point 6 onwards. Otherwise, press the [#] key to exit the PGM-W module recording
] key.
option.
6.9 How to remove PGM-/MA-220G modules.
1) Press the [
2) Select [7] RF Disp.
3) Enter the installer code.
4) Choose option [9] Delete PGM-W.
5) Enter the PGM-W number to be deleted (use the [
number). select the desired PGM-W number)
6) Confirm that you really want to delete this module by pressing the [1] key.
7) Press the [
8) If you wish to continue deleting more modules, repeat the steps from point 5.
Otherwise, press the [#] key to exit this option.
] key to return to the RF Devices menu.
] key on the keypad.
] key on the keypad.
] key to accept the confirmation of the deleted module.
] keys to enter the PGM-W
] keys to enter the PGM-W
Advertisement
Table of Contents
