Garnet PC-732G Manual page 22

Command Number 204: Keypad Zone Assignment No. 5
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 205: Keypad Zone Assignment No. 6
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 206: Keypad Zone Assignment No. 7
Default values ------------------------------------------------------------------------------> 0
Positions-------------------------------------------------------------------------------------> (1)
Command Number 207: Keypad Zone Assignment No. 8
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 220: Assign Zone No. to Module Input No. 1 Expander N° 1
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Zone No. assignment to Expander Module Input No. 1
NO. 1. The code must be 2 digits long. Valid values are 00 to 32. With the value [00]
the zone is bypassed.
Note: Commands 221 to 227 (Assign Zone No. to input No. 1 of expander module
No. 1) are programmed in the same way as command No. 220.
Command Number 221: Zone No.Assign. to Input No. 2 of Expander Module No. 1
Default values-------------------------------------------------------------------------------> 0
Positions-------------------------------------------------------------------------------------> (1)
Command Number 222: Zone No. Assignment to Input No. 3 of Expander Module
No. 1
Default values-------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 223: Zone No. Assignment to Input No. 4 of Expander Module
No. 1
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 224: Zone No. Assignment to Input No. 5 of Expander Module
No. 1
Default values-------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 225: Zone No. Assignment to Input No. 6 of Expander Module
No. 1
Default values--------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 226: Zone No. Assignment to Input No. 7 of Expander Module
No. 1
Default values -------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command Number 227: Zone No. Assignment to Input No. 8 of Expander Module
No. 1
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
22
0
2 0 4
(2)
0
2 0 5
(2)
0
2 0 6
(2)
0
2 0 7
(2)
0
2 2 0
(2)
0
2 2 1
(2)
0
2 2 2
(2)
0
2 2 3
(2)
0
2 2 4
(2)
0
2 2 5
(2)
0
2 2 6
(2)
0
2 2 7
(2)
Command Number 228: Assignment of Zone No. to Module Input No. 1
Expander N° 2
Default values -------------------------------------------------------------------------------> 0
Positions ---------------------------------------------------------------------------------------> (1)
Digit position (1)-(2): Zone No. assignment to Input No. 1 of Expander Module No.
2. The code must be 2 digits long. Valid values are 00 to 32.
With the value [00] the zone is bypassed.
Note: Commands 229 to 235 (Assign Zone No. to Expander Module No. 2 Input No.
1 are programmed in the same manner as command No. 228.
Command Number 229: Zone No. Assignment to Input No. 2 of Expander Module
No. 2
Default values -------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
Command Number 230: Zone No. Assignment to Input No. 3 of Expander Module
No. 2
Default values -------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
Command Number 231: Zone No. Assignment to Input No. 4 of Expander Module
No. 2
Default values -------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
Command Number 232: Zone No. Assignment to Input No. 5 of Expander Module
No. 2
Default values --------------------------------------------------------------------------------> 0
Positions ----------------------------------------------------------------------------------------> (1)
Command Number 233: Zone No. Assignment to Input No. 6 of Expander Module
No. 2
Default values -------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
Command Number 234: Zone No. Assignment to Input No. 7 of Expander Module
No. 2
Default values -------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
Command Number 235: Zone No. Assignment to Input No. 8 of Expander Module
No. 2
Default values--------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
Command Number 236: Assignment of Zone No. to Module Input No. 1
Expander N° 3
Default values -------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
Digit position (1)-(2): Zone No. assignment to Expander Module Input No. 1
NO. 3. The code must be 2 digits long. Valid values are 00 to 32.
Note: With the value [00] the zone is bypassed.
Note: Commands 237 to 243 (Assignment of zone no. to entry no. 1 of the
module (module expander No. 3) are programmed in the same way as command
No. 236.
Command Number 237: Zone No. Assignment to Input No. 2 of Expander Module
No. 3
Default values -------------------------------------------------------------------------------> 0
Positions----------------------------------------------------------------------------------------> (1)
0
2 2 8
(2)
0
2 2 9
(2)
0
2 3 0
(2)
0
2 3 1
(2)
0
2 3 2
(2)
0
2 3 3
(2)
0
2 3 4
(2)
0
2 3 5
(2)
0
2 3 6
(2)
0
2 3 7
(2)