Output Terminal Function Selection (Pr. 190 To Pr. 192) - Mitsubishi Electric FR-E720-0.1 K Instruction Manual

Function assignment of external terminal and control

4.11.5 Output terminal function selection (Pr. 190 to Pr. 192)

You can change the functions of the open collector output terminal and relay output terminal.
Parameter
Number
RUN terminal
190
function selection
FU terminal
191
function selection
A,B,C terminal
192
function selection
The above parameters can be set when Pr. 160 User group read selection = "0". (Refer to page 183)
* "93" and "193" can not be set in Pr. 192.
(1) Output signal list
You can set the functions of the output terminals.
Refer to the following table and set the parameters: (0 to 99: positive logic, 100 to 199: negative logic)
Setting
Signal
Positive Negative
logic logic
0 100 RUN
1 101 SU
3 103 OL
4 104 FU
7 107 RBP
8 108 THP
11 111 RY
12 112 Y12
13 113 Y13
14 114 FDN
15 115 FUP
16 116 RL
20 120 BOF
25 125 FAN
26 126 FIN
46 146 Y46
47 147 PID
64 164 Y64
90 190 Y90
140
Name
Open collector
output terminal
Relay
output terminal
Function
Output during operation when the inverter output frequency
Inverter running
rises to or above Pr. 13 Starting frequency.
Up to frequency ∗1
Output when the output frequency is reached to the set frequency. Pr. 41
Overload alarm Output while stall prevention function is activated.
Output frequency Output when the output frequency reaches the frequency
detection set in Pr. 42 (Pr. 43 for reverse rotation).
Regenerative brake
Output when 85% of the regenerative brake duty set in Pr.
pre-alarm 70 is reached.
Output when the electronic thermal value reaches 85% of
Electronic thermal O/L
the trip level. (Electronic thermal relay function protection
relay pre-alarm
(E.THT/E.THM) activates, when the value reached 100%.)
Output when reset process is completed (when the inverter
Inverter operation
can be started by switching the start signal ON or while it is
ready
running) after powering on inverter.
Output current Output when the output current is higher than the Pr. 150
detection setting for longer than the time set in Pr. 151 .
Output when the output power is lower than the Pr. 152
Zero current detection
setting for longer than the time set in Pr. 153 .
Output when the feedback value falls below the lower limit
PID lower limit
of PID control.
Output when the feedback value rises above the upper limit
PID upper limit
of PID control
PID forward/reverse
Output when forward rotation is performed in PID control.
rotation output
Output to open the brake when the brake sequence
Brake opening request
function is selected.
Fan fault output Output at the time of a fan fault.
Heatsink overheat Output when the heatsink temperature reaches about 85%
pre-alarm of the heatsink overheat protection providing temperature.
During deceleration at Output when the power failure-time deceleration function is
occurrence of power executed.
failure (retained until release)
During PID control
Output during PID control.
activated
During retry Output during retry processing.
Output when any of the control circuit capacitor, main
Life alarm circuit capacitor and inrush current limit circuit or the
cooling fan approaches the end of its service life.
Initial
Initial Signal
Value
0 RUN (inverter running)
FU (output frequency
4
detection)
99 ALM (fault output)
Operation
Setting Range
0, 1, 3, 4, 7, 8, 11 to 16, 20, 25,
26, 46, 47, 64, 90, 91, 93*, 95,
96, 98, 99, 100, 101, 103, 104,
107, 108, 111 to 116, 120, 125,
126, 146, 147, 164, 190, 191,
193*, 195, 196, 198, 199, 9999
Refer
Related
Parameter
Page
—
142
144
Pr. 22, Pr. 23,
Pr. 66
Pr. 42, Pr. 43 144
Pr. 70 125
Pr. 9, Pr. 51 112
—
142
Pr. 150,
145
Pr. 151
Pr. 152,
145
Pr. 153
Pr. 127 to
236
Pr. 134
Pr. 278 to
Pr. 283, 130
Pr. 292
Pr. 244 252
—
285
Pr. 261 163
Pr. 127 to
236
Pr. 134
Pr. 65 to
165
Pr. 69
Pr. 255 to
253
Pr. 259
to
88