Adjustable case sealer with accuglide 3 taping heads (176 pages)
Summary of Contents for 3M 3M-Matic 7000r-I
Page 1
Instructions and Parts List 3M-Matic ™ 7000r-I / 7000r3-I Pro Type 11700 Random Case Sealer AccuGlide ™ Taping Heads Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
Page 2
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page ii Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 3
Replacement Parts and Service Information To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. ™ ™ ® It has been set up and tested in the factory with Scotch Tapes. ® If technical assistance or replacement parts are needed, call or fax the appropriate number listed below.
Page 4
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page iv Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 5
EU DECLARATION OF CONFORMITY Original Name and address of the manufacturer and, where applicable, his authorised representative: 3M Deutschland GmbH, Closure and Masking Systems Division Carl-Schurz-Strasse 1 D41453 Neuss, Germany This declaration of conformity is issued under the sole responsibility of the manufacturer.
Page 6
Replacement Parts and Service Information To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set ™ ™ ® up and tested in the factory with Scotch tapes. If any problems occur when operating ®...
Page 8
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page viii Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 9
10 .3 Electric System / Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™...
Page 10
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page x Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Drawings and Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 – End of Manual Taping Head Information Manual 2 and 3: AccuGlide 3 Taping Heads — 2 Inch or 3 Inch ™ (See Manual 2 or 3 for Table of Contents) International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page xi Source Document for all related Manuals/Translations...
Page 12
AccuGlide ..Trademark of 3M St. Paul, MN 55144-1000 Scotch ..Trademark of 3M St. Paul, MN 55144-1000 Drw... . Drawing Ex.
The 7000r-I / 7000r3-I Pro automatically adjusts to a wide range of box sizes (see “Specifications Section – Box Weight and Size Capacities”). The 3M-Matic ™...
2.1 Data Identifying Manufacturer and Machine Identi cation Plate Data for Technical Assistance and Service Agent/Distributor or Local After Sale Service: International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 3 Source Document for all related Manuals/Translations...
Page 16
Contents: 7000r-I / 7000r3-I Pro Random Case Sealer (1) 7000r-I / 7000r3-I Pro Random Case Sealer, Type 11700 (1) Tool/Spare Parts Kit (1) Instruction and Parts Manual International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021...
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 5 Source Document for all related Manuals/Translations...
Never put your hands inside any part the machine is running. of the machine while it is working. Serious injury may occur (Figure 3-4). International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021...
Page 19
- Always feed boxes into the machine Figure 3-8 by pushing only from the end of box. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 7...
Page 20
- The operator must pay attention qualified personnel to operate and to the blades during the tape service this equipment. replacement. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 8 Source Document for all related Manuals/Translations...
Tape replacement button Blade replacement Electric power Drive belt replacement disconnected Ordinary maintenance International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 9 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 22
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 10 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Pressure (inside box) (not shown) Gauge Figure 3-9: 7000r-I / 7000r3-I Pro Case Sealer Components (Left Front View) International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 11 Source Document for all related Manuals/Translations...
78-8137-8338-4 78-8137-8331-9 78-8137-8331-9 78-8070-1421-8 78-8137-0226-9 78-8137-0219-4 78-8137-0886-0 78-8137-7406-0 Figure 3-10: Replacement Labels / 3M Part Numbers International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 12 Source Document for all related Manuals/Translations...
Page 25
78-8137-8339-2 3M Logo 78-8133-8339-2 (Each side of upper as- sembly - Not shown) 78-8133-8333-5 78-8070-1339-2 (2) Figure 3-11: Replacement Labels / 3M Part Numbers International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021...
Pneumatic: 90PSIG [6.2 bar], 11.6 SCFM [1200 NL/Min] Peak Usage. The machine is equipped with a 2.4m [8 foot] standard neoprene covered power cord. Contact your 3M Representative for power requirements not listed above. 4.2 Operating Rate: Belt speed is 0..5m/s [100 F.P.M.] Actual production rate is dependent on operator’s dexterity.
2.25” [57] Maximum N/A 26" [660] 26" [660] 36" [914] 25.5” [647] International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 15 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 28
Special modifications may be available for carton sizes not listed on previous page. Contact your 3M Representative for information. Note: The case sealer can accommodate most boxes within the size range listed above. However, if the box length (in direction of seal) to box height ratio is .6 or less, then several boxes should be test run to assure proper machine performance.
• Supplied infeed and optional exit conveyors (if used) should provide straight and level box entry/exit. • Optional exit conveyor (powered or gravity) can help move sealed boxes away from machine. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™...
Page 30
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 18 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Figure 5-4 - Do not stack anything over machine. - It is possible to stack a maximum of 2 machines (if in original packing). International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021...
For the disposal of the above materials, please follow the environmental directives or the law in your country. Figure 6-5 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 20 Source Document for all related Manuals/Translations...
5 - For Outer Column Repositioning- See Special Set-up Procedure (Section 11). Figure 7-3 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 21 Source Document for all related Manuals/Translations...
Figure 7-5 (see Technical Documentation/ Spare Parts-Order Section). Figure 7-6 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 22 Source Document for all related Manuals/Translations...
Page 35
3 litre/min. [0.1 SCFM]. The case sealer requires a 6.2 bar gauge pressure 166 liter/min [90 PSIG], @21°C, 1.01 bar [11.6 SCFM] International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 23...
Page 36
Bumper Supports. Cable Buffing Column Guards are Roller then installed. Figure 7-7 7000r-I / 7000r3-I Pro Frame Set-Up International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 24 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
To change tape leg length to 50mm [2.0 inch], see “Special Set-Up Procedure – Changing the Figure 7-11 Centering Guides Tape Leg Length.” International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 25...
For more information on bumper settings, make sure that all packaging materials contact your 3M service representative. and tools are removed from the machine. Do not plug electrical cord into outlet until ready to run machine.
Electrical Control Box- (not shown) Air Pressure Regulator, Upper Figure 7-14 Controls, Valves and Switches Drive Assembly Pneumatic Force International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 27 Source Document for all related Manuals/Translations...
Page 40
Centering Guides close (centering the box), and Upper Drive release (after box passes sensor), the guides open. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 28 Source Document for all related Manuals/Translations...
- Always feed boxes into the machine by raised position. Adjust force higher (+)/ pushing only from the end of the box. Lower (-) to equalize and create balance. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021...
Depressing upper drive assem- bly raising switch causes upper drive assembly to rise, releasing the switch Figure 7-21 Drive Belts causes drive assembly to descend. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 30...
Ground (Protective Earth) wires of the 1 - Remove lower taping head from machine to the appropriate terminals of the machine. plug following plug manufacturers instructions International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 31...
The LATCHING EMERGENCY STOP BUTTON is located on the top center of the machine (Figure 8-4). Figure 8-4 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 32 Source Document for all related Manuals/Translations...
Lock Regulator-Filter Solenoid Exhaust Valve Supply Connector Regulator Figure 9-4 Filter International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 33 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
- - 3 3 3 3 9 9 - - 9.7 Air Pressure Regulator / Upper Drive Force Adjustment Figure 9-8 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 34 Source Document for all related Manuals/Translations...
3 3 9 9 - - Figure 9-8 Figure 9-9 9.9 Box Conveying / Tape Seal Application Direction International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 35 Source Document for all related Manuals/Translations...
• Have a maximum length of personnel to operate and service this 30.5m [100 ft] equipment. • Be properly grounded. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 36 Source Document for all related Manuals/Translations...
5. Refer to Manual 2 or 3, “Adjustments – Changing Tape Leg Length” for taping head set-up. 6. Replace taping heads reverse of disassembly. Turn on air supply/electric power, unlatch upper drive assembly and allow it to return to its rest position. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™...
- Turn pneumatic and electrical supply off and disconnect before performing any adjustments, maintenance or servicing the machine or taping heads. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 38...
7 Conveyor bed height adjustment 2. Latching emergency stop button 8 Special Adjust-Changing tape leg 3. STOP (OFF) (O) main switch 9 Special Adjust-Column re-position International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 39...
Centering guides not centered Adjust centering guides Check box specifications Box flaps not of equal length (continued) International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 40 Source Document for all related Manuals/Translations...
Page 53
Defective centering guide power Clean/replace valve / realign valve/proximity sensor misaligned sensor and sensor receptacle with sensor receptacle International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 41 Source Document for all related Manuals/Translations...
13. Maintenance and Repairs (continued) 13.8 Box Drive Belt Replacement Note – 3M recommends replace- ment of drive belts in pairs, especially if belts are unevenly worn. Lower Drive Belts - Figure 13-1 1. Remove and retain center plate (A) and four (4) screws.
3.5kg (7lbs) Pull Force with 25mm (1 inch) at Mid span Infeed End Discharge End Figure 13-4 Box Drive Belt Tension Adjustment International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 44...
Page 57
Belts Lock Wrench Infeed End Figure 13-5 Box Drive Belt Tension Adjustment, Lower Belts (Infeed End) International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 45 Source Document for all related Manuals/Translations...
Page 58
Screws (4) Lock Wrench Infeed End Hex Head Tension Screw Figure 13-6 Box Drive Belt Tension Adjustment, Upper Belts (Infeed End) International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 46 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
3) Cause malfunction of machine. These events can potentially cause damage to machine. For more infor- Figure 13-7 Case Sealer Frame Changes mation on bumper settings, contact your 3M service representative. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™...
Assembly Spacer(s) Note: Remove Column Screws Column Spacer (#2) Column Spacer (#1) International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 48 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 61
3. Turn on the air and electrical power to the case sealer. The upper taping head will now descend only part way thus increasing operating speed. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 49...
Page 62
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 50 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
________ _____________________________________________________ ________ _____________________________________________________ ________ _____________________________________________________ ________ _____________________________________________________ ________ _____________________________________________________ ________ _____________________________________________________ International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 51 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 64
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 52 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Electrical tests Earth continuity 2 - Insulation resistance 3 - High voltage test Reference; EN60204-1 par. 20.2.,3.,4. International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 53 Source Document for all related Manuals/Translations...
PLAN \P \PROGETT ROGETT I\ I\Si Siat at s s.p .p.a .a\S \SI I AT\S \Sia iat s. t s.p. p.a\SI a\SI A T AT\3 \3M\ M\7000A_R- 7000A_R- 8000A\ 8000A\ 7000R\ 7000R\ 7000 7000 -R -R_2016 _2016 \S \Schem...
Page 67
PLAN\ PRO PRO GE GETT TTI\ I\Si Siat at s s.p .p.a .a\S \SI I AT\S \Sia iat s. t s.p. p.a\SI a\SI A T AT\3 \3M\ M\7000A_R- 7000A_R- 8000A\ 8000A\ 7000R\ 7000R\ 7000 7000 -R -R_2016\Schem _2016\Schem i i ma...
Page 68
PLAN\ PRO PRO GE GETT TTI\ I\Si Siat at s s.p .p.a .a\S \SI I AT\S \Sia iat s. t s.p. p.a\SI a\SI A T AT\3 \3M\ M\7000A_R- 7000A_R- 8000A\ 8000A\ 7000R\ 7000R\ 7000 7000 -R -R_2016\Schem _2016\Schem i i ma...
Page 69
PLAN\ PRO PRO GE GETT TTI\ I\Si Siat at s s.p .p.a .a\S \SI I AT\S \Sia iat s. t s.p. p.a\SI a\SI A T AT\3 \3M\ M\7000A_R- 7000A_R- 8000A\ 8000A\ 7000R\ 7000R\ 7000 7000 -R -R_2016\Schem _2016\Schem i i ma...
Page 70
PLAN\ PRO PRO GE GETT TTI\ I\Si Siat at s s.p .p.a .a\S \SI I AT\S \Sia iat s. t s.p. p.a\SI a\SI A T AT\3 \3M\ M\7000A_R- 7000A_R- 8000A\ 8000A\ 7000R\ 7000R\ 7000 7000 -R -R_2016\Schem _2016\Schem i i ma...
Page 71
PLAN\ PRO PRO GE GETT TTI\ I\Si Siat at s s.p .p.a .a\S \SI I AT\S \Sia iat s. t s.p. p.a\SI a\SI A T AT\3 \3M\ M\7000A_R- 7000A_R- 8000A\ 8000A\ 7000R\ 7000R\ 7000 7000 -R -R_2016\Schem _2016\Schem i i ma...
16. Technical Documentation and Information (continued) 16.2 Technical Diagrams - Pneumatic International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 60 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Delay (T-1 controlled): Delay (T-1 controlled): Open Centering Guides Open Centering Guides 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions International - ENG 3M-Matic ™ February 2021 Page 61 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 74
The threading tool, part number • Figure Number 78-8076-4726-4 contained in the kit is • Position also available as a replacement stock item. • 3M Part Number (11 Digits) Replacement Parts Ordering • Description Information and Service • Quantity Refer to the first page of this instruction Refer to Manual 2 or 3 for recom- manual “Replacement Parts and Service...
Page 75
Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on special order. Contact 3M/Tape Dispenser Parts to confirm item availability International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™...
Page 76
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 64 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 77
Figure 16020/B Figure 16026 Figure 16004 Figure 15962 Figure 16024 Frame Assemblies International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 65 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 78
Mounting Bracket - Lower Taping Head Note: See Parts List for Figure 16016 AccuGlide 2” and 3” information International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 66 Source Document for all related Manuals/Translations...
Page 79
7000r-I / 7000r3-I Pro Figure 16016 Ref. No. 3M Part No. Description 16016-1 78-8017-9169-6 Nut - M18x1 - Galvanized 16016-2 78-8070-1395-4 Arm - Tape Head (Upper and Lower) 16016-3 78-8137-0998-3 Bracket - Roller Holder (Lower) 16016-4 78-8076-4519-3 Shaft - Tape Drum 2” 78-8060-8462-6 Shaft - Tape Drum 3” 16016-5 78-8098-8817-1 Leaf - Spring 2” 78-8098-8830-4 Leaf - Spring 3” 16016-6 26-1002-5753-9 Screw - Self Tapping 7SPX8...
Page 80
*16b Option *4b Option *16a Exit Conveyor (Optional) Casters Optional Figure 16026 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 68 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 81
7000r-I / 7000r3-I Pro Figure 16026 Ref. No. 3M Part No. Description 16026-1 78-8137-7723-8 Rollers Bed Assembly 16026-2 78-8114-4818-8 Screw - M8X14 Soc . Hd . Hex . Hd . 16026-3 78-8017-9318-9 Washer - 8mm Plain 16026-4a 78-8137-7997-8 Infeed Bracket 16026-4b 78-8137-7985-3 Infeed Bracket...
Page 82
* Column Block Assembly includes Part Numbers 9, 10, and 19 Also Refer to Special Set-Up Procedures Figure 16028 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 70 Source Document for all related Manuals/Translations...
Page 84
Figure 16021/A Figure 16021/B Figure 16021/B For E-Stop Information: See Figure 16021/B Figure 16021 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 72 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 86
7000r-I / 7000r3-I Pro Figure 16021/A International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 74 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 87
7000r-I / 7000r3-I Pro Figure 16021/A Ref. No. 3M Part No. Description 16021/A-1 78-8052-6718-0 Motor - 220/415v, 50 Hz, 3 Phase 78-8100-0865-2 Motor - 200/220v, 50/60 Hz, 3 Phase 78-8052-6719-8 Motor - 260/440v, 50 Hz, 3 Phase 78-8046-8267-8 Motor - 100/110v, 50/60 Hz, 1 Phase 0.12kw 78-8046-8268-6 Motor - 220/240v, 50 Hz, 1 Phase 0.12kw 78-8076-4590-4 Motor - 220/240v, 60 Hz, 1 Phase 16021/A-2 78-8060-7880-0 Eyelet Terminal / 4 Red 16021/A-3 78-8137-8277-4 Screw - M8X20 Zinc 16021/A-4 78-8017-9318-9...
Page 88
7000r-I / 7000r3-I Pro Figure 16021/B International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 76 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 89
7000r-I / 7000r3-I Pro Figure 16021/B Ref. No. 3M Part No. Description 16021/B-1 78-8137-8292-3 Screw - M6X16 16021/B-2 78-8010-7435-8 Washer - M6 Lock 16021/B-3 78-8052-6709-9 Washer - Special 16021/B-4 78-8052-6710-7 Roller - Idler 16021/B-5 78-8100-1239-9 Belt Tensioning - L/H 16021/B-6 78-8100-1238-1 Belt Tensioning - R/H...
Page 90
7000r-I / 7000r3-I Pro Figure 16020/B Figure 16020/A Figure 16020 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 78 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 91
7000r-I / 7000r3-I Pro Figure 16020 Ref. No. 3M Part No. Description 16020-1 78-8137-8121-4 Screw - M6X12 Special 16020-2 78-8137-7983-8 Frame - Bottom Drive Belt w/Nutzers 16020-3 78-8137-8123-0 Screw - M5X20 16020-4 78-8070-1534-8 Stud - Side Plate 16020-5 78-8060-8488-1 Screw - M5X20 Hex . Hd .
Page 92
7000r-I / 7000r3-I Pro Figure 16020/A International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 80 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 93
7000r-I / 7000r3-I Pro Figure 16020/A Ref. No. 3M Part No. Description 16020/A-1 78-8052-6718-0 Motor - 220/415v, 50 Hz, 3 Phase 78-8100-0865-2 Motor - 200/220v, 50/60 Hz, 3 Phase 78-8052-6719-8 Motor - 260/440v, 50 Hz, 3 Phase 78-8046-8267-8 Motor - 100/110v, 50/60 Hz, 1 Phase 0.12kw 78-8046-8268-6 Motor - 220/240v, 50 Hz, 1 Phase 0.12kw 78-8076-4590-4 Motor - 220/240v, 60 Hz, 1 Phase 16020/A-2 78-8060-7880-0 Eyelet Terminal / 4 Red 16020/A-3 78-8137-8277-4 Screw - M8X20 Zinc 16020/A-4 78-8017-9318-9...
Page 94
7000r-I / 7000r3-I Pro Figure 16020/B International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 82 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 95
7000r-I / 7000r3-I Pro Figure 16020/B Ref. No. 3M Part No. Description 16020/B-1 78-8060-8416-2 Nut - M20X1 Special 16020/B-2 78-8052-6713-1 Ring - Polyurethane 16020/B-3 78-8137-8291-5 Motor Pulley 16020/B-4 78-8070-1529-8 Support - Shaft 16020/B-5 78-8070-1530-6 Radial Ball Bearing - 6205-2RS, O .D . 52 16020/B-6 78-8054-8986-7 Sprocket - 3/8” Pitch 28 Teeth...
Page 96
7000r-I / 7000r3-I Pro 33 25 Figure 16024 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 84 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 98
7000r-I / 7000r3-I Pro Figure 16054 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 86 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 100
7000r-I / 7000r3-I Pro 15 16 Figure 16004 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 88 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 102
7000r-I / 7000r3-I Pro 7/17 Figure 15962 International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 90 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Page 104
International - ENG 3M-Matic 7000r-I / 7000r3-I Pro - Type 11700 Original Instructions ™ February 2021 Page 92 Source Document for all related Manuals/Translations 44-0009-2165-8 / ECO# 0078045...
Instructions and Parts List 3M-Matic ™ Accuglide ™ Upper and Lower High Speed Taping Heads 2 Inch Type 10800 Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
Page 106
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page ii Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 107
Included with each machine is an Instructions and Parts List manual. Technical Assistance/Replacement Parts and Additional Manuals: Call 3M-Matic™ Help line. Provide the customer support coordinator with the model/ machine name, machine type, and serial number that are located on the identification plate (For example: Accuglide 3 - 2 inch - Type 10800 - Serial Number 13282).
Page 108
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page iv Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 109
Replacement Parts and Service Information (continued) To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set ™ ™ ® up and tested in the factory with Scotch tapes. If any problems occur when operating ®...
Page 110
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page vi Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 111
Replacement Parts and Service ......19-20 Replacement Parts Illustrations and Parts List ..21-End of Manual International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™...
Page 112
Buyer shall indemnify and hold Seller harmless against any claim by third parties resulting from failure to comply with the aforesaid laws and standards. AccuGlide , Scotch , and 3M-Matic are Trademarks of 3M, St. Paul, Minnesota 55144-1000 ™ ™ ™ International - ENG...
Page 113
® seam of regular slotted containers. These taping heads are incorporated into most standard 3M-Matic™ case sealers. The compact size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™ case sealers. This includes replacement of other types of taping, gluing or stapling heads in existing case sealing machines.
Page 114
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 2 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 115
3M Closure and Masking Systems Division 3M Center, St. Paul, MN 55144-1000 (USA) Edition 2021/Copyright 3M 2021. All rights reserved The manufacturer reserves the right to change the product at any time without notice. How to use this Manual The manual is an important part of the machine; all information contained herein is intended to enable the equipment to be maintained in perfect condition and operated safely.
Page 116
The blades are extremely sharp. system is running (Important Safeguards continued on next page) International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 117
See "Replacement Parts Illustrations and Parts Lists" for label part numbers. Upper Taping Head Label 78-8137-3317-3 Lower Taping Head Label 78-8137-3316-5 78-8070-1335-0 Figure 1-1 Replacement Labels/3M Part Numbers International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™...
Page 118
5. Box Size Capacities: For use with center seam regular slotted containers. When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifications for box weight and size capacities. 6. Operating Rate: Conveyor speeds up to 0.5 m/s [100 feet per minute].
Page 119
* This dimension can be reduced to 90mm [3.5 in.] when both heads are converted to 50mm [2 in.] tape leg lengths. Figure 2-1 Dimensional Drawing International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 120
Taping Head is supplied with a buffing the transportation company and also arm guard. Adjustments to guard may notify your 3M Representative. be required to install taping head into some older design case sealers. Installation Guidelines 4.
Page 121
Tape Adhesive Side Tape Supply Roll Tape Drum Figure 3-2 Taping Head Components/Threading Diagram - Lower Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 9 Source Document for all related Manuals/Translations...
Page 122
2. Lower taping head is loaded and Figure 3-3 Tape Loading/Threading threaded in same manner as upper head. International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 10...
Page 123
Excess tape can be cut with a scissors at applying roller. Figure 3-4 Tape Loading/Threading Figure 3-5 Tape Loading/Threading International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 11...
Page 124
Should tape adhesive build-up occur on blade, carefully wipe clean with an oily cloth. (Maintenance continued on next page.) International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 12...
Page 125
Figure 4-2 Roller Shaft Section View this socket after removing one screw to hold the shaft for removal of the second screw (See Figure 4-2). International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 126
- Never attempt to work on the taping head or load tape while the box drive system is running (adjustments continued on next page.) International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 127
Figure 5-5 One-Way Tension Roller - Never attempt to work on the taping head or load tape while the box (Adjustments continued on next page.) International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 128
The blades are extremely sharp. system is running International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 129
If not, press bearing further into roller or replace roller. International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 130
Centering guides not centered Adjust centering guides Box flaps not of equal length Check box specifications International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 18 Source Document for all related Manuals/Translations...
Page 131
Spring – Torsion Replacement Parts and Service Refer to the first page of this instruction manual “Replacement Parts and Service Information". International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 132
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 20 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 133
Information" for replacement parts ordering information. Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm item availability. International - ENG 3M-Matic...
Page 134
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 22 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 135
Figure 10922 Figure 10919 Figure 10921 Figure 10920 Tape Head - AccuGlide ™ 3 - 2 inch International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 23 Source Document for all related Manuals/Translations...
Page 136
AccuGlide 3 - 2" ™ Figure 10925 – Upper Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 24 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 138
AccuGlide 3 - 2" ™ Figure 10922 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 26 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 140
AccuGlide 3 - 2" ™ Figure 10919 – Upper Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 28 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 141
AccuGlide 3 - 2" ™ Figure 10919 – 2" Upper Head Ref. No. 3M Part No. Description 10919-1 78-8137-3300-9 Buffing Arm – Sub Assembly 10919-2 78-8137-3301-7 Buffing Arm – Sub Assembly 10919-3 78-8052-6575-4 Shaft – Roller 10919-4 78-8137-1398-5 Roller - Buffing Assembly 10919-5 78-8070-1220-4 Spacer – Spring 10919-6 78-8052-6580-4 Spacer 10919-7 26-1003-5829-5 Screw –...
Page 142
3 - 2" ™ Figure 10923 Upper and Lower Heads Figure 10923 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 30 Source Document for all related Manuals/Translations...
Page 143
AccuGlide 3 - 2" ™ Figure 10923 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10923-1 78-8137-3302-5 Link – Assembly 10923-3 78-8137-3304-1 Shaft – Pivot, Buffing 10923-4 78-8017-9082-1 Bearing – Special 30 mm 10923-5 78-8017-9106-8 Screw – Bearing Shoulder...
Page 144
AccuGlide 3 - 2" ™ Figure 10921 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 32 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 145
AccuGlide 3 - 2" ™ Figure 10921 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10921-1 78-8137-3307-4 Frame – Cut-Off Weldment 10921-2 78-8017-9173-8 Blade – 65 mm/2.56 Inch 10921-3 26-1003-8596-7 Screw - Hex Hd M5 x 8 w/ Ext. Tooth Lockwasher...
Page 146
AccuGlide 3 - 2" ™ Figure 10401 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 34 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 148
AccuGlide 3 - 2" ™ Figure 10924 – Lower Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 36 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 150
AccuGlide 3 - 2" ™ Figure 10920 – Lower Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 38 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 151
AccuGlide 3 - 2" ™ Figure 10920– Lower Head Ref. No. 3M Part No. Description 10920-1 78-8137-3300-9 Buffing Arm – Sub Assembly 10920-2 78-8137-3301-7 Buffing Arm – Sub Assembly 10920-3 78-8052-6575-4 Shaft – Roller 10920-4 78-8137-1398-5 Roller - Buffing Assembly 10920-5 78-8070-1220-4 Spacer – Spring 10920-6 78-8052-6580-4 Spacer 10920-7 26-1003-5829-5 Screw – Hex Hd, M6 x 12...
Page 152
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 40 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 153
Instructions and Parts List 3M-Matic ™ Accuglide ™ Type 10800 Upper and Lower High Speed Taping Heads 3 Inch Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
Page 154
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page ii Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Included with each machine is an Instructions and Parts List Manual. Technical Assistance/Replacement Parts and Additional Manuals: Call the 3M-Matic™ Help line. Provide the customer support coordinator with the model/ machine name, machine type, and serial number that are located on the identification plate (For example: Model - Accuglide 3 High Speed 3”...
Page 156
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page iv Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 157
Replacement Parts and Service Information (continued) To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set ™ ™ ® up and tested in the factory with Scotch tapes. If any problems occur when operating ®...
Page 158
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page vi Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 159
Replacement Parts and Service ......19-20 Replacement Parts Illustrations and Parts List ..21-End of Manual International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™...
Page 160
Buyer shall indemnify and hold Seller harmless against any claim by third parties resulting from failure to comply with the aforesaid laws and standards. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions...
® seam of regular slotted containers. These taping heads are incorporated into most standard 3M-Matic™ case sealers. The compact size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™ case sealers. This includes replacement of other types of taping, gluing or stapling heads in existing case sealing machines.
Page 162
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 2 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
(ELV), a glossary with a definition of symbols, plus a parts list of the 3M-Matic™ Accugllide 3 (3 inch) 3M Closure and Masking Systems Division 3M Center St.
The blades are extremely sharp. system is running (Important Safeguards continued on next page) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 4...
Page 165
See "Replacement Parts Illustrations and Parts Lists" for label part numbers. Upper Taping Head Label 78-8137-3317-3 Lower Taping Head Label 78-8137-3316-5 78-8070-1335-0 Figure 1-1 Replacement Labels/3M Part Numbers International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™...
90mm [3.5 inches] (with optional 2 inch leg length) Case Sealer Width – 150mm [6 inches] When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifications for box weight and size capacities.
* This dimension can be reduced to 90mm [3.5 in.] when both heads are converted to 50mm [2 in.] tape leg lengths. Figure 2-1 Dimensional Drawing International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021...
Taping Head is supplied with a buffing the transportation company and also arm guard. Adjustments to guard may notify your 3M Representative. be required to install taping head into some older design case sealers. Installation Guidelines 4.
Tension Roller Tape Adhesive Side Tape Supply Roll Tape Drum Figure 3-2 Taping Head Components/Threading Diagram - Lower Head (Left Side View) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 9...
2. Lower taping head is loaded and Figure 3-3 Tape Loading/Threading threaded in same manner as upper head. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 10...
Page 171
Excess tape can be cut with a scissors at applying roller. Figure 3-4 Tape Loading/Threading Figure 3-5 Tape Loading/Threading International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 11 Source Document for all related Manuals/Translations...
Silicone. Should tape adhesive build-up occur on blade, carefully wipe clean with an oily cloth. (Maintenance continued on next page.) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 12 Source Document for all related Manuals/Translations...
Insert a 4mm hex key wrench into this socket after removing one screw to hold the shaft for removal of the second screw. See Figure 4-2. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 13...
- Never attempt to work on the taping head or load tape while the box drive system is running (adjustments continued on next page.) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021...
- Never attempt to work on the taping Figure 5-5 One-Way Tension Roller head or load tape while the box drive system is running (Adjustments continued on next page.) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 15...
The blades are extremely sharp. system is running International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 16...
If not, press bearing further into roller or replace roller. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 17...
Page 178
Centering guides not centered Adjust centering guides Box flaps not of equal length Check box specifications International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 18 Source Document for all related Manuals/Translations...
78-8113-7030-9 Spring – Torsion Replacement Parts and Service Refer to the first page of this instruction manual “Replacement Parts and Service Information". International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 19...
Page 180
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 20 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 181
Information" for replacement parts ordering information. Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm item availability. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™...
Page 182
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 22 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 183
10929 Figure 10926 (Upper) Figure 10928 Figure 10927 (Lower) Assemblies - AccuGlide ™ 3 - 3 inch International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 23 Source Document for all related Manuals/Translations...
Page 184
AccuGlide 3 - 3” ™ Figure 10932 – Upper Head International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 24 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 186
AccuGlide 3 - 3” ™ Figure 10929 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 26 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 188
AccuGlide 3 - 3” ™ Figure 10926 – Upper Head International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 28 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 189
AccuGlide 3 - 3” ™ Figure 10926 – Upper Head Ref. No. 3M Part No. Description 10926-1 78-8137-3300-9 Buffing Arm – Sub Assembly 10926-2 78-8137-3301-7 Buffing Arm – Sub Assembly 10926-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon 10926-4 78-8137-1397-7 Roller – Buffing Assembly 10926-5 78-8076-4739-7 Spacer – Spring 10926-6 78-8052-6580-4...
Page 190
AccuGlide 3 - 3” ™ Figure 10930 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 30 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 191
AccuGlide 3 - 3” ™ Figure 10930 – Upper and Lower Heads Ref. No. 3M Part No. Description 10930-1 78-8137-3302-5 Link – R/H Assembly 10930-3 78-8137-3314-0 Shaft – Pivot, Buffing 10930-4 78-8017-9082-1 Bearing – Special 30 mm 10930-5 78-8017-9106-8 Screw – Bearing Shoulder...
Page 192
AccuGlide 3 - 3” ™ Figure 10928 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 32 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 194
AccuGlide 3 - 3” ™ Figure 10402 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 34 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 195
AccuGlide 3 - 3” ™ Figure 10402 – 3" Latch Upper and Lower Heads Ref. No. 3M Part No. Description 10402-1 78-8070-1395-4 Bracket – Bushing Assembly 10402-2 78-8060-8462-6 Shaft – Tape Drum, 3 Inch Head 10402-3 78-8017-9169-6 Nut – M18 x 1...
Page 196
AccuGlide 3 - 3” ™ 17 19 Figure 10931 – Lower Head International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 36 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 198
AccuGlide 3 - 3” ™ Figure 10927 – Lower Head International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 38 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 199
AccuGlide 3 - 3” ™ Figure 10927 – Lower Head Ref. No. 3M Part No. Description 10927-1 78-8137-3300-9 Buffing Arm – Sub Assembly 10927-2 78-8137-3301-7 Buffing Arm – Sub Assembly 10927-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon 10927-4 78-8137-1397-7 Roller – Buffing 10927-5 78-8076-4739-7 Spacer – Spring 10927-6 78-8052-6580-4...
Page 200
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 40 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 201
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 41 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 202
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 42 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...