Advertisement
TLP Pro 1225TG, 1525TG, and 1725TG • Setup Guide
Reset Modes: A Brief Summary
These touchpanels offer the following reset modes. For full information about the modes, see the TLP Pro 1225, 1525, and 1725
Series User Guide.
Use factory firmware:
•
Reset All IP Settings:
•
Reset to Factory
•
Defaults:
Enable or Disable the
•
DHCP Client:
Setup Menu
MENU
Press the
button (
figure 5
setup menu. Select any of the six available screens (
Network
Display
Audio
,
,
the appropriate button in the navigation bar at the top of the
screen (for more information, see the TLP Pro 1225, 1525, and
1725 Series User Guide).
Figure 7 shows the setup menu for the TLP Pro 1225TG. The
setup menu for the TLP Pro 1525TG and TLP Pro 1725TG are
very similar.
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide
For information about replacing and disposing of batteries, see the TLP Pro 1225, TLP Pro 1525, and TLP Pro 1725 Series User
Guide at www.extron.com.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
6
Use this mode to replace firmware in the event of firmware failure. Press and hold the
I
button (
figure 5
,
Use this mode to reset all network settings without affecting user-loaded files. Press and
RESET
hold the
button for 6 seconds. After the
momentarily press the
Use this mode to return the touchpanel to factory default settings, including passwords. Press
RESET
and hold the
button for 9 seconds. After the
momentarily press the
NOTES:
The factory configured passwords for all accounts on this device have been set to the
•
device serial number. Passwords can be changed during configuration. Passwords
are case sensitive.
If the device is reset to default settings, the passwords are reset to the default
•
password, which is
Use this mode to toggle between DHCP enabled and DHCP disabled. Press the
five times, consecutively. After the fifth press, do not press the button again within 3 seconds.
If DHCP was enabled, it is now disabled and the
disabled, it is now enabled and the
NOTES:
By default DHCP is off and the unit uses a static IP address.
•
When you disable the DHCP client, the unit reverts to using the previously-set static
•
IP address.
H
,
, on page 4) to open the
Status
Input
Advanced
,
and
) by tapping
on the Extron website.
© 2020-2021 Extron Electronics — All rights reserved.
All trademarks mentioned are the property of their respective owners.
on page 4) while applying power to the unit.
RESET
RESET
button.
RESET
button.
extron
admin
(for either
RESET
RESET
LED blinks six times.
Status
Network
,
Info
Model:
TLP Pro 1225TG
Part Number:
60-1788-02
Firmware
Version:
1.02.0000.b003
Bootloader
Version:
1.03.0000
PoE:
Active
Setup Menu: Status Page for TLP Pro 1225TG
Figure 7.
www.extron.com
J
LED (
) blinks twice, release and
RESET
LED blinks three times, release and
user
or
).
RESET
LED blinks three times. If DHCP was
Display
Audio
Input
Advanced
Network
Display
IP Address:
192.168.254.251
Resolution:
1280x800
DHCP:
Off
Project:
1280x800
Host Name:
TLP-AB-CD-EF
Sleep Timer:
5 Minutes
Audio
Input
System Volume:
100
HDMI:
No Signal
System Mute:
Off
XTP:
1280x720
Advanced
Controller IP:
192.168.254.250
Project Size:
1/197 MB
RESET
button
Exit
HDCP
68-3474-51 Rev. C
09 21
Advertisement
