Extron electronics TLP Pro 1225MG Setup Manual

TLP Pro 1225MG, 1525MG, and 1725MG • Setup Guide
Overview
The Extron TLP Pro 1225MG, TLP Pro 1525MG, and TLP Pro 1725MG are wall-mounted touchpanels with capacitive, edge-to-edge
®
glass touchscreens. The TLP Pro 1225MG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1525MG has a 15.6 inch
screen with a 1366x768 resolution. The TLP Pro 1725MG has a 17.3 inch screen with a 1920x1080 resolution. All three touchpanels
are ideal for any AV applications requiring large touchpanels with flexible mounting options and fully customizable interfaces. This
guide provides instructions for experienced installers to mount and install these touchpanels. For more complete details, see the
TLP Pro 1225, 1525, and 1725 Series User Guide at
Setup Checklist
Get Ready
… Download and install the latest version of the following software:
… GUI Designer — Used to design layouts for Extron TouchLink
… Global Configurator
… Global Scripter
Global Scripter provides an Extron-exclusive Python
… Toolbelt — Used for device discovery, device information, firmware updates, and configuration of network settings, system
utilities, and user management for TouchLink Pro devices.
NOTE: All four software programs are available from
… Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you also require:
…
… IP address
… Username — This can be either admin or user.
… Passwords — The factory configured passwords for all accounts on this device have been set to the device serial number.
Passwords can be changed during configuration. Passwords are case sensitive.
NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron (for
either admin or user).
… Make a note of the touchpanel MAC address from the label on the back of the device.
Mount and Cable All Devices
ATTENTION:
Do not power on the touchpanels until you have read the Attention in the "Power Supply" section of the
•
TLP Pro 1225, 1525, and 1725 Series User Guide.
Ne branchez pas les écrans tactiles avant d'avoir lu la mise en garde dans la section « sources d'alimentation » du TLP Pro
•
1225, 1525, and 1725 Series User Guide.
… Mount the units. There are several mounting options for TouchLink Pro touchpanels (see
… Connect cables to the touchpanels (see
… Connect the touchpanel to a Power over Ethernet (PoE) injector. The TLP Pro 1725MG ships with the PI 140 power injector.
A power injector must be purchased separately for the 12-inch and 15-inch models.
… Connect an Extron IP Link
Set up the Touchpanels for Network Communication
… Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork.
… Use the Setup Menu
address, subnet mask, gateway, and related settings for the touchpanel.
Configure the Touchpanels
… Create a graphical user interface with GUI Designer (see GUI Designer Help File for step-by-step instructions).
… Associate functions with the graphical user interface features by configuring (see the Global Configurator Help File) or
programming (see the Global Scripter Help File) the system.
www.extron.com
Plus and Professional — Used to set up and configure the control processor and touchpanel.
®
— Used to rovide an integrated development environment for Extron control systems programming.
®
… Subnet mask
Rear Panel Features
Pro control processor to the same Ethernet subnetwork as the touchpanel.
®
(see page 6) or Toolbelt (see Toolbelt Help File) to set the DHCP status and, if necessary, the IP
.
Pro touchpanels and third party touch interfaces.
®
library (ControlScript ) and modules to get you started.
™ ®
www.extron.com
.
… Gateway
on page 4).
Mounting
on page 2).
1