Advertisement
Connecting Power
ATTENTION:
Do not power on the touchpanels until you have read the ATTENTION in the "Rear Panel Features" section of the
•
TLP Pro 1225 and TLP Pro 1525 Series User Guide.
Ne branchez pas les écrans tactiles avant d'avoir lu la mise en garde dans la section « Rear Panel Features » du
•
TLP Pro 1225 and TLP Pro 1525 Series User Guide.
The power injector must be purchased separately. Figure 4 shows the Extron PI 140. Your power injector may look different.
Connect a straight-through Ethernet cable from the power injector to a switch or
1.
1
router (see figure 4,
or router to the power supply input.
Connect a second straight-through cable (
2.
TLP Pro touchpanel XTP/LAN/PoE connector (see
This cable carries the network information and 48 VDC from the power injector
to the touchpanel.
Connect the IEC power cord to a convenient 100 VAC to 240 VAC, 50-60 Hz
3.
power source (
3
).
Alternatively, use an Ethernet cable to connect the XTP/LAN/PoE port of the interface
to a PoE+ switch or connect the touchpanel directly to an XTP model that is capable
of remotely powering a touchpanel (see the
Reset Modes: a Brief Summary
The TLP Pro 1225MG and TLP Pro 1525 MG offer the following reset modes. For full information about the modes, see the
TLP Pro 1225 and TLP Pro 1525 Series User Guide.
Use factory firmware:
•
Reset All IP Settings:
•
Reset to Factory Defaults: Use this mode to return the interface to factory default settings. Press and hold the Reset
•
Enable or Disable the
•
DHCP Client
Setup Menu
Press the Menu button (
figure 2
D
, on page 4) to open the setup menu. Select any of the
six available screens ( Status , Network , Display , Audio ,
Input and Advanced ) by pressing the appropriate button in the
navigation bar at the top of the screen (for more information, see the
TLP Pro 1225 and TLP Pro 1525 Series User Guide).
Figure 5 shows the setup menu for the TLP Pro 1225MG. The setup
menu for the TLP Pro 1525MG is almost identical.
). This cable carries network information from the switch
2
) from the power injector to the
figure 3
note
on page 4).
Use this mode to replace firmware in the event of firmware failure. Press and hold the Reset
figure 3
button (see
,
Use this mode to reset all network settings without affecting user-loaded files. Press and
hold the Reset button for 6 seconds. After the Reset LED (
momentarily press the Reset button.
button for 9 seconds. After the Reset LED flashes three times, release and momentarily press
the Reset button.
NOTES:
The factory configured passwords for all accounts on this device have been set to the
•
device serial number. Passwords can be changed during configuration. Passwords are
case sensitive.
If the device is reset to default settings, the passwords are reset to the default
•
password, which is extron (for either admin or user).
Use this mode to toggle between DHCP enabled and DHCP disabled.
Press the Reset button five times, consecutively. After the fifth press, do not press the button
again within 3 seconds. If DHCP was enabled, it is now disabled and the Reset LED blinks
three times. If DHCP was disabled, it is now enabled and the Reset LED blinks six times.
F
figure 3
,
on page 3 or
I
,
, on page 4).
C
) while applying power to the unit.
Status
Network
,
Info
Model:
TLP Pro 1225MG
Part Number:
60-1787-02
Firmware
Version:
1.02.0000.b003
Bootloader
Version:
1.03.0000
PoE:
Active
Figure 5.
Setup Menu: Status page for TLP Pro 1225MG
Product Category
100-240V~50/60 Hz
1.1A MAX
INPUT
OUTPUT
LAN
POWERED TLP
3
Extron PI 140
1
To a TLP Pro
To Network or
touchpanel
XTP Device
Figure 4.
Connecting the Power Injector
B
) flashes twice, release and
Audio
Advanced
Display
Input
Network
Display
IP Address:
192.168.254.251
Resolution:
1280x800
DHCP:
Off
Project:
1280x800
Host Name:
TLP-AB-CD-EF
Sleep Timer:
5 Minutes
Audio
Input
Master Volume:
100
HDMI:
No Signal
Master Mute:
Off
XTP:
1280x720
Advanced
Controller IP:
192.168.254.250
Project Size:
1/197 MB
2
Exit
HDCP
5
Advertisement
