Brother DCP-1510 Service Manual page 179

1.3.19 Print frame p 1.3.19 Print frame pattern (single-side pr
<Function> <Function>
This function is used to print a frame pattern on a single side of the paper and to check for This function is used to print a frame pattern on a single side of the paper and to check for
printing flaws. printing flaws.
<Operating Procedure> <Operating Procedure>
Be sure to set letter size paper for test pattern printing before commencing the following Be sure to set letter size paper for test pattern printing before commencing the following
procedure. procedure.
(1 (1) ) Nu
(2) "PRINT (2)
(3) T T o print the f (3)
(4) When the [S (4)
Error display Error display
T T O O N N E E R R E E M M P P T T Y Y
C C o o v v e e r r i i s s O O p p e e n n
N N o o P P a a p p e e r r
J J a a m m T T r r a a y y 1 1
J J a a m m R R e e a a r r
attern (single-side printing) (function code: 69)
Nume meri ric ke c key pa y pad mo d mode dels ls
Press the [6] and [9] buttons in this order in the initial state of maintenance mode. Press the [6] and [9] buttons in this order in the initial state of maintenance mode.
Non-numeric key pad models Non-numeric key pad models
Pres Pr ess th s the [ e [ ] or ] or [ [ ] bu ] butt tton t
[OK] button. [OK] button.
"PRINTING" is di ING" is displaye splayed on the LCD d on the LCD, and the fr
the paper. the paper.
When printing is completed, "WAKU SX" is displayed on the LCD. When printing is completed, "WAKU SX" is displayed on the LCD.
Note: Note:
• • If printing fai If printing fails, printi ls, printing is stopped and one of the error ng is stopped and one of the errors shown in the table bel
displayed. T displayed. To retry printing, refer to the o retry printing, refer to the "Remedy" in the table below to eliminate the
cause of the error, and press the [Start] button. cause of the error, and press the [Start] button.
o print the frame pat rame pattern agai tern again, press th
When the [Stop/Exi top/Exit] button i t] button is presse
maintenance mode. maintenance mode.
L L C C D D
R R e e p p l l a a c c e e t t h h e e t t o o n n e e r r c c a a r r t t r r i i d d g g e e . .
C C l l o o s s e e t t h h e e t t o o p p c c o o v v e e r r . .
S S e e t t p p a a p p e e r r i i n n t t h h e e p p a a p p e e r r t t r r a a y y . .
R R e e m m o o v v e e t t h h e e j j a a m m m m e e d d p p a a p p e e r r . .
R R e e m m o o v v e e t t h h e e j j a a m m m m e e d d p p a a p p e e r r . .
Print pattern Print pattern
4-28 4-28
inting) (function code: 69)
on to di o disp spla lay "M y "MAI AINTE NTENA NANC
, and the frame pat ame pattern is pri
"Remedy" in the table below to eliminate the
n, press the [St e [Start] but art] button.
s pressed, the mach d, the machine retur ine returns to the ini
R R e e m m e e d d y y
NCE 69 E 69" on " on th the LC e LCD an D and pr d pres
tern is printed on a sin nted on a single side o
s shown in the table below is
ton.
ns to the initial st tial state of ate of
Confidential Confidential
ess th s the e
gle side of f
ow is