Brother DCP-1510 Service Manual page 171

1.3.13 1.3.13 Change USB Change USB No. return v
Change USB No. return value Change USB No. return value
<Function> <Function>
When the operating system (OS) installed on the computer is Windows Vista When the operating system (OS) installed on the computer is Windows Vista
machine is connected to this computer using USB2.0FULL, the OS may not be able to obtain machine is connected to this computer using USB2.0FULL, the OS may not be able to obtain
the USB device serial number depending on the computer and USB device. If the serial the USB device serial number depending on the computer and USB device. If the serial
number cannot be obtained, the number of devices increases each time the device is number cannot be obtained, the number of devices increases each time the device is
connected to the computer. To avoid this problem, setting this function to "USBNo.=ON" can connected to the computer. To avoid this problem, setting this function to "USBNo.=ON" can
fix the USB No. return value to "0". fix the USB No. return value to "0".
U U S S B B N N o o . . = = O O N N
U U S S B B N N o o . =
The setting currently selected is marked "*" at the end of the display. The setting currently selected is marked "*" at the end of the display.
<Operating Procedure> <Operating Procedure>
(1 (1) ) Nu
(2) "USBNo (2)
(3 (3) ) "U
(4) (4) Press the [S
(5) Tu (5)
Note: Note:
• • The settin
No. return value (function c
L L C C D D
R R e e t t u u r r n n " " 0 0 " " . .
. = O O F F F F R R e e t t u u r r n t
Nume meri ric ke c key pa y pad mo d mode dels ls
Press the [4] and [5] buttons in this order in the initial state of maintenance mode. Press the [4] and [5] buttons in this order in the initial state of maintenance mode.
Non-numeric key pad models Non-numeric key pad models
Pres Pr ess th s the [ e [ ] or ] or [ [ ] butt tton t ] bu
[OK] button. [OK] button.
"USBNo." is dis ." is displaye played on the L d on the LCD. Pre
"USB SBNo No.= .=ON ON" is " is di disp spla laye yed on
"USBNo.=ON" when fixing the serial number return value to "0" or "USBNo.=OFF" when "USBNo.=ON" when fixing the serial number return value to "0" or "USBNo.=OFF" when
not fixing it. not fixing it.
Press the [Start] bu tart] button. "Acce tton. "Accepted" is di
the initial state of maintenance mode. the initial state of maintenance mode.
Turn rn OFF OFF the the pow power er swi switch. tch.
The setting is applied af g is applied after the power sw ter the power switch is turn
4-20 4-20
alue (function code: 45) ode: 45)
D D e e s s c c r r i i p p t t i i o o n n
n th h e s e se e r r i i a a l n l nu u m m b b e e r o r of t f th h e m
on to di o disp spla lay "M y "MAI AINTE NTENA NANC
CD. Press the [S ss the [Start] b tart] button.
d on th the L e LCD CD. Pr . Pres ess t s the he [ [
pted" is displaye splayed on the LCD, and th d on the LCD, and the machine re
itch is turned OFF and then ON agai ed OFF and then ON again. n.
® ®
, and the , and the
e ma a c c h h i i n n e e . ( . (D D e e f f a a u u l l t t ) )
NCE 45 E 45" on " on th the LC e LCD an D and pr d pres
utton.
] o ] or [ r [ ] but utto ton to ] b n to di disp spla lay y
e machine returns to
Confidential Confidential
ess th s the e
turns to