Brother DCP-1510 Service Manual page 111

7.4 7.4 Document scanner unit / Document cover (only for models without ADF unit) Document scanner unit / Document cover (o
(1) (1) Ope
(2) (2) Disco
(3) (3) Relea
(4) (4) Open th
(5) (5) Remov
(6) (6) Remove th
(7) (7) Remove th
Taptite bind B M4x12 Taptite bind B M4x12
Document Document
scanner unit scanner unit
Taptite pan B M4x14 Taptite pan B M4x14
(only for models without ADF unit) (only for models without ADF unit)
Document Document
scanner unit scanner unit
Harness routing: Refer to " Harness routing: Refer to
/ fuser unit (DCP-15** series without fan, MFC-18** series without / fuser unit (DCP-15** series without fan, MFC-18** series without fan)
PCB ASSY / low voltage power supply PCB unit / fuser unit (DCP-15** series with fan, MFC- PCB ASSY / low voltage power supply PCB unit / fuser unit (DCP-15** series with fan, MFC-
18** series with 18** series with fan)
fuser unit (DCP-16** series, MFC-19** fuser unit (DCP-16** series, MFC-19** series)
Assembling Note: Assembling Note:
• • After
Open the n the doc docume ument s nt scan canner u
Disconnect the C nnect the CIS flat cabl IS flat cable, the docu
cable from the main PCB ASSY cable from the main PCB
Release the hook o se the hook of the pull- f the pull-arm, and r
Open the docum e document scan ent scanner uni
Remove the two ta e the two taptite bi ptite bind B M4x12 sc
Disconnect the panel flat cable from the panel PCB ASSY to remove the panel unit from Disconnect the panel flat cable from the panel PCB ASSY to remove the panel unit from
the document scanner unit. the document scanner unit.
Remove the two tap e two taptite pan B M tite pan B M4x14 scre
document scanner unit (only for models without ADF unit). document scanner unit (only for models without ADF unit).
Remove the hinge fro e hinge from the docu m the document cove
without ADF unit). (2 locations) without ADF unit). (2 locations)
Panel flat cable Panel flat cable
Panel unit Panel unit
90° 90°
Hook Hook
Pull-arm Pull-arm
Pull-arm Pull-arm
Main PCB ASSY Main PCB ASSY
" 1. 1. Frame R / main PCB ASSY / low voltage power supply PCB unit Frame R / main PCB ASSY / low voltage power supply PCB unit
fan)" " , , " " 3. 3. Frame R / main PCB ASSY / low voltage power supply PCB unit / Frame R / main PCB ASSY / low voltage power supply PCB unit /
After the the replac replacement, ement, refer refer to to "
OR CIS UNIT" in chapter OR CIS UNIT" in chapter 3
2-23 2-23
nly for models without ADF unit)
ner unit nit. .
e, the document sca ment scanner moto nner motor harness
ASSY, then pull out the , then pull out the CIS flat cable from CIS flat cable from the hole.
arm, and remove it fr emove it from the docu om the document sca
ner unit 90 degr t 90 degrees and r ees and remove i
nd B M4x12 screws. Re rews. Release the f lease the four hook
4x14 screws to remo ws to remove the docu
ment cover by tilti r by tilting it 120 deg
Hooks Hooks
Fig. 2-17 Fig. 2-17
series)" " and " and " 7 7 . .
" 3 3 . . IF YOU REPLACE THE DOCUMENT SCANNER IF YOU REPLACE THE DOCUMENT SCANNER UNIT
3 to enter the adjusted value of the laser unit. to enter the adjusted value of the laser unit.
r harness, and the pa , and the panel flat
the hole.
ment scanner uni nner unit. t.
emove it by pul t by pulling it ling it up. up.
our hooks of the pan s of the panel unit.
ve the document cov ment cover from the er from the
ng it 120 degrees (onl rees (only for model y for models s
Panel PCB ASSY Panel PCB ASSY
Hinges (only for models Hinges (only for models
without ADF unit) without ADF unit)
Hole Hole
120° 120°
Document scanner Document scanner
motor harness motor harness
CIS flat cable CIS flat cable
Panel flat cable Panel flat cable
fan)" " , , " " 2 2 . . Frame R / main Frame R / main
Panel flat cable Panel flat cable" " . .
Confidential Confidential
nel flat
el unit.
Document Document
cover cover
(only for (only for
models models
without without
ADF unit) ADF unit)
UNIT