Brother DCP-1510 Service Manual page 41

Error code 0900 Error code 0900
Print Unable 09 Print Unable 09
Turn the power off and Turn the power off and then back on again.
Detected irregular power supply more than 100 times. Detected irregular power supply more than 100 times.
<User Check> <User Check>
• • Turn OFF the pow
Note: Note:
• • The irregul
Error code 0A02 Error code 0A02
Print Unable 0A Print Unable 0A
Turn the power off and Turn the power off and then back on again.
The fan failure was detected. The fan failure was detected.
Error code 0B01 Error code 0B01
Print Unable 0B Print Unable 0B
Turn the power off and Turn the power off and then back on again.
An error occurred in the high voltage power supply PCB ASS An error occurred in the high voltage power supply PCB ASSY while operating.
Error code 0B02 Error code 0B02
Print Unable 0B Print Unable 0B
Turn the power off and Turn the power off and then back on again.
An error occurred in the high voltage power supply PCB ASSY when An error occurred in the high voltage power supply PCB ASSY when the machine is in the
ready state. ready state.
then back on again.
Turn OFF the power switch. Af er switch. After severa
that this error has reset. that this error has reset.
S S t t e e p p C C a a u u s s e e
Low voltage power supply PCB Low voltage power supply PCB
failure failure
1 1
2 2 M M a a i i n n P P C C B B f f a a i i l l u u r r e e
The irregular power supply de ar power supply detection err
large distortion in the power supply voltage supplied to the machine. In this case, if the large distortion in the power supply voltage supplied to the machine. In this case, if the
same power supply is used, the same error may occur even when the low voltage same power supply is used, the same error may occur even when the low voltage
power supply PCB unit is replaced. Ask the user to review the installation environment. power supply PCB unit is replaced. Ask the user to review the installation environment.
then back on again.
S S t t e e p p C C a a u u s s e e
Harness connection failure of Harness connection failure of
1 1
the fan the fan
2 2 F F a a n n f f a a i i l l u u r r e e
3 3 M M a a i i n n P P C C B B f f a a i i l l u u r r e e
then back on again.
then back on again.
S S t t e e p p C C a a u u s s e e
Connection failure of the high Connection failure of the high
1 1
voltage PCB harness voltage PCB harness
2 2 High voltage power supply PCB High voltage power supply PCB
failure failure
3 3 M M a a i i n n P P C C B B f f a a i i l l u u r r e e
1 25 1 25
ter several seconds, tur l seconds, turn ON the power again and ch n ON the power again and check
Replace the low voltage power supply PCB Replace the low voltage power supply PCB
unit. Reset the irregular power supply unit. Reset the irregular power supply
detection counter after replacement. (Refer to detection counter after replacement. (Refer to
" " 4.1 Resetting Irregular Power Supply 4.1 Resetting Irregular Power Supply
Detection Counter" in Chapter 3 Detection Counter" in Chapter
R R e e p p l l a a c c e e t t h h e e m m a a i i n n P P C C B B A A S S S S Y Y . .
tection error (error code: 0900 or (error code: 0900) occurs when there is a
Check the harness connection of the fan and Check the harness connection of the fan and
reconnect it. reconnect it.
R R e e p p l l a a c c e e t t h h e e f f a a n n . .
R R e e p p l l a a c c e e t t h h e e m m a a i i n n P P C C B B A A S S S S Y Y . .
Reconnect the high voltage PCB harness. Reconnect the high voltage PCB harness.
Replace the high voltage power supply PCB Replace the high voltage power supply PCB
ASSY. ASSY.
R R e e p p l l a a c c e e t t h h e e m m a a i i n n P P C C B B A A S S S S Y Y . .
eck
R R e e m m e e d d y y
3. . ) )
) occurs when there is a
R R e e m m e e d d y y
Y while operating.
the machine is in the
R R e e m m e e d d y y