Table of Contents
Advertisement
IMPORTANT
CAREFULLY READ THIS INSTRUCTION
MANUAL
before installing or operating the ID-
RP4000V.
SAVE THIS INSTRUCTION MANUAL.
manual contains important safety and operating in-
structions for the ID-RP4000V.
Refer to the ID-RP2 instruction manual, supplied
with the ID-RP2C, for details about D-STAR system
repeater instructions, installation and precautions.
This instruction manual describes only the ID-
RP4000V's particular installation and precautions.
PRECAUTIONS
R WARNING RF EXPOSURE!
Radio Frequency
energy. Extreme caution should
(RF)
be observed when operating this device. If you have
any questions regarding RF exposure and safety stan-
dards please refer to the Federal Communications
Commission Office of Engineering and Technology's
report on Evaluating Compliance with FCC Guidelines
for Human Radio Frequency Electromagnetic Fields
.
(OET Bulletin 65)
R WARNING HIGH VOLTAGE! NEVER
antenna or internal antenna connector during transmis-
sion. This may result in an electrical shock or burn.
R WARNING HIGH VOLTAGE! NEVER
antenna at any location where a person could easily
touch the antenna during transmission. This may result
in an electrical shock or burn.
R WARNING! NEVER
IN] connector. This could cause a fire or damage the
ID-RP4000V.
R WARNING! NEVER
the [DC 13.8V IN] connector. This could cause a fire or
damage the ID-RP4000V.
R WARNING! NEVER
jects touch any internal part or connectors on the ID-
RP4000V. This may result in an electric shock or this
could cause a fire or damage the ID-RP4000V.
R WARNING! NEVER
RP4000V with wet hands. This may result in an elec-
tric shock or may damage to the ID-RP4000V.
R WARNING! NEVER
a power source using reverse polarity. This will dam-
age the ID-RP4000V.
Make sure the ID-RP4000V's power is turned OFF
when connecting a DC power cable.
This device emits
touch an
install the
apply AC to the [DC 13.8V
apply more than 16 V DC to
let metal, wire or other ob-
operate or touch the ID-
connect the ID-RP4000V to
EXPLICIT DEFINITIONS
WORD
R WARNING!
This
CAUTION
NOTE
DO NOT
use or place the ID-RP4000V in areas with
temperatures below –10°C
.
(+122°F)
DO NOT
place the ID-RP4000V in excessively dusty
environments or in direct sunlight.
DO NOT
place the ID-RP4000V against walls or put-
ting anything on top of the units. This will obstruct heat
dissipation.
DO NOT
use harsh solvents such as benzine or alco-
hol to clean the ID-RP4000V, as they will damage the
ID-RP4000V's surfaces. If the ID-RP4000V becomes
dusty or dirty, wipe it clean with a soft, dry cloth.
DO NOT
modify the ID-RP4000V for any reason.
Place the ID-RP4000V in a secure place to avoid inad-
vertent use by children.
Use the specified fuse only.
For the U.S.A. only
CAUTION:
RP4000V, not expressly approved by Icom Inc., could
void your authority to operate the ID-RP4000V under
FCC regulations.
Icom, Icom Inc. and the Icom logo are registered trade-
marks of Icom Incorporated (Japan) in Japan, the United
States, the United Kingdom, Germany, France, Spain, Rus-
sia and/or other countries.
Microsoft, Windows and Windows Vista are registered
trademarks of Microsoft Corporation in the United States
and/or other countries.
All other products or brands are registered trademarks or
trademarks of their respective holders.
i
DEFINITION
Personal injury, fire hazard or elec-
tric shock may occur.
Equipment damage may occur.
If disregarded, inconvenience only. No
risk or personal injury, fire or electric
shock.
(+14°F)
Changes or modifications to the ID-
or above +50°C
Advertisement
Table of Contents
