Download
Share
Print this page
Icom IC-FR3000 Remote Control Manual
  1. Manuals
  2. Brands
  3. Icom Manuals
  4. Repeater
  5. IC-FR3000 Series
  6. Remote control manual

Icom IC-FR3000 Remote Control Manual

Vhf/uhf fm repeater
Hide thumbs Also See for IC-FR3000:

Advertisement

Quick Links

See also: Service Manual , Instruction Manual
REMOTE CONTROL MANUAL
iFR3000
iFR4000
1 REMOTE CONTROL FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1
1-1 REMOTE CONTROL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1-2 REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1-3 COMMAND TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1-4 COMMAND DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1-5 OPERATION EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1-6 OPERATION EXAMPLE FOR PHONE PATCH . . . . . . . . . . . . . . . . 12
VHF FM REPEATER
UHF FM REPEATER

Advertisement

loading
Need help?

Need help?

Do you have a question about the IC-FR3000 and is the answer not in the manual?

Questions and answers

Related Manuals for Icom IC-FR3000

Summary of Contents for Icom IC-FR3000

  • Page 1: Table Of Contents

    REMOTE CONTROL MANUAL VHF FM REPEATER iFR3000 UHF FM REPEATER iFR4000 1 REMOTE CONTROL FUNCTION ......1 1-1 REMOTE CONTROL SETTING .

  • Page 2: Remote Control Function

    REMOTE CONTROL FUNCTION 1-1 REMOTE CONTROL SETTING D D System control To enable remote control functions the DTMF settings (RX System Code, TX System Code, DTMF Setting, TX Code CH (Autodial), etc.) must be pre-programmed using CS-FR3000 cloning software. Use CS- FR3000 help screens for description of functions and operation and for programming details.

  • Page 3: Remote Control Operation

    REMOTE CONTROL OPERATION 1-2 REMOTE CONTROL OPERATION D D System control command NOTE: All commands must be entered within 10 sec. of entering a password. It is possible to enter the password and command continuously. Format of Command • Basic command code The Basic command code consists of a fixed 4-digit command code, preceded by a 1-digit Header Tone, and followed by a 1-digit De-limiter Tone.

  • Page 4: Command Table

    REMOTE CONTROL OPERATION 1-3 COMMAND TABLE During During Default Normal mode Phone Patch mode Function SUB code Code Transceiver Phone Transceiver Phone ✔ ✔ ✔ ✔ System Control Exit 0002 † — ✔ ✔ Repeat Start 0003 — — — ✔...

  • Page 5: Command Descriptions

    REMOTE CONTROL OPERATION 1-4 COMMAND DESCRIPTIONS • System Control Exit • TX/RX Unit OFF Turns OFF “System Control standby mode” and Turn OFF the TX/RX units. This command is not returns to normal operating mode. Will also “Hang available from a transceiver or during Phone Patch up”...

  • Page 6: Operation Example

    REMOTE CONTROL OPERATION 1-5 OPERATION EXAMPLE D D System control command NOTE: • All commands must be entered within 10 sec. of The following examples assume these codes entering a password. If the input time period are pre-programmed in the repeater. Other runs out, you must enter the password again.
  • Page 7 REMOTE CONTROL OPERATION OPERATION EXAMPLE (Continue) D D RF Power (Low) (0007 Default) This command is available from both the transceiv- er and phone line. This explanation shows the step by step operation from the transceiver or operation from the phone line when entering password and command continuously (one after the other).
  • Page 8 REMOTE CONTROL OPERATION OPERATION EXAMPLE (Continue) D D RF Power (High) (0008 Default) This command is available from both the transceiv- er and phone line. This explanation shows the oper- ation from the transceiver when entering the pass- word and command continuously or step by step operation from the phone line (one after the other).
  • Page 9 REMOTE CONTROL OPERATION OPERATION EXAMPLE (Continue) D D RX Unit OFF D D TX/RX Unit OFF (0011 Default) (0009 Default) This command is available from the phone line This command is available from the phone line only. This explanation shows the step by step oper- only.
  • Page 10 REMOTE CONTROL OPERATION OPERATION EXAMPLE (Continue) D D Master Enable D D Slave Enable (0014 Default) (0013 Default) This command is available from both the transceiv- This command is available from the transceiver and er and phone line. This explanation shows the step phone line.
  • Page 11 REMOTE CONTROL OPERATION OPERATION EXAMPLE (Continue) D D Mch Select (0017 Default) This command is available from both the transceiv- er and phone line. This explanation shows the step by step operation from the transceiver or operation from the phone line when entering the password and command continuously (one after the other).
  • Page 12 REMOTE CONTROL OPERATION OPERATION EXAMPLE (Continue) D D CPU All Reset (0018 Default) This command is available from the phone line only. This explanation shows entering the password and command continuously. This command cannot be performed while repeater is transmitting, therefore you must stop the repeater operation before performing CPU All Reset.

  • Page 13: Operation Example For Phone Patch

    REMOTE CONTROL OPERATION 1-6 OPERATION EXAMPLE FOR PHONE PATCH D D Description D D TEL Autodial (0016 Default) Phone Patch function allows communication to a Autodial number: 12 (Channel 12) q Enter the following DTMF codes. transceiver from a telephone line, or connection to a telephone line from a transceiver.
  • Page 14 S-6228I-1US 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan © 2004 Icom Inc.

This manual is also suitable for:

Ic-fr4000