Maytag Commercial MLE27PD Installation Instructions Manual page 28

ELECTRONIC CONTROL SETUP INSTRUCTIONS ELECTRONIC CONTROL SETUP INSTRUCTIONS
Display
Once the unit has been plugged in and the dryer door opened
and closed, the display will show the price.
PRICE
1.50
PRICE
1.50
Control Set-up Procedures
IMPORTANT: Read all instructions before operating.
The fabric setting buttons along with the digital display are used
to set up the dryer controls. The display can contain 4 numbers
and/or letters and a decimal point. These are used to indicate
the set-up codes and related code values available for use in
programming the appliance.
How to Use the Buttons to Program the Controls
1. The WHITES AND COLORS button is used to adjust the values
associated with set-up code. Pressing the button will change
the value by increments of one (1). Rapid adjustment is possible
by holding down the button.
2. The PERM. PRESS button will advance through the set-up
codes. Pressing the button will advance to the next available
set-up code. Holding down the PERM. PRESS button will
automatically advance through the set-up codes at a rate faster
than one (1) per second.
3. The DELICATES button is used to select or deselect options.
IMPORTANT: The console must not be opened unless power is
first removed from the dryer. To access connector AA1:
→ Unplug dryer or disconnect power.
→ Open console, disconnect plug on AA1, close console.
→ Plug in dryer or reconnect power.
Insert access panel key and turn counterclockwise.
■
If manual set-up card is not available, manual set-up mode can be
entered by turning the access panel key.
The dryer is now in the set-up mode.
NOTE: This dryer is preset at the factory and does not require any
programming. However, if you want to change the settings, follow
the "Set-Up Codes" guide below.
This dryer is pre-set at the factory for fixed cycle price with
■
top off.
Set-Up Codes
The PERM. PRESS button will advance you from code to code.
■
The WHITES AND COLORS button will change the code
■
value.
The DELICATES button will select or deselect options.
■
NOTE: On all stacked dryer models, programming selections apply
to both dryers. Stacked dryer selections are accessed by pressing
the LOWER DRYER buttons, you can not program upper dyer
differently than lower dryer and vice versa.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or three
right-hand characters.
28
UPPER DRYER
PERMANENT
WHITES
DELICATES
& COLORS
PRESS
HIGH HEAT MEDIUM HEAT LOW HEAT
WHITES PERMANENT
DELICATES
& COLORS PRESS
HIGH HEAT MEDIUM HEAT LOW HEAT
LOWER DRYER
Code Explanation
606
REGULAR CYCLE PRICE
Mode 6 allows you to set up how many quarters (coin 1) you
want customers to pay for cycle (i.e. if mode 6 set to 6 that
means it will take 6 quarters or $1.50 to start cycle).
606 Advance from 0–39 by pressing the WHITES AND
COLORS button. Factory default of 6 quarters = $1.50.
•
Press the PERM. PRESS button once to advance
to next code.
705 REGULAR DRY TIME
Mode 7 is the amount of time per cycle in minutes. It uses the
number of quarters from mode 6 and multiplies to number set
in mode 7 to give cycle time (i.e. if mode 6 =6 and mode 7=5,
then the time per cycle is 6X5 or 30 minutes).
705 Factory default of 5 minutes per coin.
By pressing the WHITES AND COLORS button,
value adjusts from 1–99 minutes.
•
Press the PERM. PRESS button once to advance
to next code.
800 TYPE OF DRYER PRICING
Mode 8 allows you to set up an additional time for user to keep
clothes in and continue cycle (i.e. if set to 00 then customer can
get an additional 5 min (factory default) cycle time for 1 quarter
inserted.) If mode 8 set to FC then no top off allowed.
800 Fixed Cycle with Top Off.
8FC Fixed Cycle.
Use DELICATES button to make this selection.
COIN MODEL: Factory preset to 00
•
Press the PERM. PRESS button once to advance
to next code.
9 00 CYCLE COUNTER OPTION
This option is either NOT SELECTED "OFF"
or SELECTED "ON."
MODE 9 allows you to keep track of how many cycles your
machine has done.
9 00 Not Selected "OFF."
9 0C Selected "ON" and not able to be deselected.
•
Press the DELICATES button 3 consecutive times
to select "ON." Once selected "ON" it cannot be
deselected.
•
Press the PERM. PRESS button once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Cycles in HUNDREDS
2 00 Cycles in ONES
This is "VIEW ONLY" and cannot be cleared.
•
Press the PERM. PRESS button once to advance to next code.
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225