Electronic Control Setup Instructions - Maytag Commercial MLE27PD Installation Instructions Manual

IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished,
but failure may occur at a later date due to ESD stress.
Use an anti-static wrist strap. Connect wrist strap to green
■
ground connection point or unpainted metal in the appliance.
Touch your finger repeatedly to a green ground connection point
or unpainted metal in the appliance.
Before removing the part from its package, touch the
■
anti-static bag to a green ground connection point or
unpainted metal in the appliance.
Avoid touching electronic parts or terminal contacts; handle
■
electronic control assembly by edges only.
When repackaging failed electronic control assembly in
■
anti-static bag, observe above instructions.
General User Information
LOCATE KEY – The key is located in the drum with this literature
and foot caps.
DO NOT LOOSE this key-The key is used to enter service mode
to allow you to set up machine for use. The machines come pre-
configured from the factory:
MODEL PD (coin drop or free vend see note):These models are
configured for 30 min dryer cycle time at a cost of $1.50 per
cycle as default from factory.
Mode 6 default is 06.
Mode 7 default is 05.
Price and Time is primarily set up through mode 6 & 7. Mode
6 is how many quarters (i.e. default = 6 =$1.50) & Mode 7 is
how much cycle time per quarter. Mode 7 defaults to 5 from
factory (max time is 75 minutes). Mode 6 and 7 gets multiplied to
determine cycle time. (6X5=30 minutes per cycle by default.)
Note: If you set mode 6 to 00, this will be a free vend and the
cycle time treats it as a 1 so if Mode 6=00 and Mode 7=45 the
cycle time is 45 minutes and no cost.
MODEL PR (free or pay reader ready).
These models default to mode 6=00 and Mode 7 = 45. This is a
free vend with a cycle time of 45 minutes, see explanation in PD
section.

ELECTRONIC CONTROL SETUP INSTRUCTIONS

ELECTRONIC CONTROL SETUP INSTRUCTIONS
-OR-
Key located
inside drum
BLANK DISPLAY – This condition indicates the dryer is
inoperative. Enter set-up mode to view diagnostic code.
"0 MINUTES" SHOWING IN DISPLAY – This indicates the
cycle is complete and the dryer cannot be operated. Coins
dropped or debit inputs during this condition will be stored in
escrow but cannot be used until normal operation is restored by
opening and closing the door. If a door switch has failed, it must be
replaced before normal operation can be restored.
COLD START (Initial first use) – Dryer is programmed at the
factory as follows:
5 minutes dry time/quarter (coin 1)
$1.50 dry price (fixed cycle with top off)
WARM START (after power failure) – A few seconds after
power is restored, if a cycle was in progress at the time of the
power failure, "RESELECT CYCLE" will flash in the display,
indicating
a button needs to be pressed to restart dryer.
PRICING – After the door is opened and then closed following the
completion of a cycle, the display indicates the cycle price (unless
set for free operation). As coins are dropped or debit inputs arrive,
the display will change to lead the user through the initiation of a
cycle.
There are four (4) types of dryer pricing:
Fixed "Vend" Pricing
A dryer set up for "Fixed Cycle" operation can only accept
additional time accumulated by increments equal to the length
of a complete dry cycle. A maximum number of minutes may be
purchased; no additional credit is given for coins dropped when
the maximum minutes are displayed.
Accumulator Pricing
If the price is set to one coin 1, then accumulator pricing is in effect
(Fixed Cycle with Top Off option must also be selected). Cycle
time can be purchased one coin at a time up to the maximum time
of 99 minutes. All money will be credited to a cycle with a single
button press while in accumulator pricing.
Fixed Cycle With Top Off Pricing
A dryer set to offer "Top Off" capability will allow time to be
added to an existing dry cycle in increments equal to the number
of minutes of dry time per quarter (coin 1), up to the maximum
minutes, regardless of the cost required to start the dryer. No
credit is given for coins or debit inputs entered when the control
is displaying the maximum minutes.
Penny increment offset is not applied to top off purchases.
FREE CYCLES – This is established by setting the cycle price
to zero. When this happens, "SELECT CYCLE" will appear
rather than a cycle price. Any cycle started as a free cycle will
automatically terminate when the door is opened.
DEBIT CARD READY – This dryer is debit card ready. It will
accept a variety of debit card systems, but does NOT come with a
debit card reader. Refer to the debit card reader manufacturer for
proper dryer setup. In models converted to a Generation 1 debit
card system, debit pulses represent the equivalent of one coin
(coin 1).
27