Advertisement
Quick Links
SUNVIEW II PLAY SYSTEM – F24061
INSTALLATION AND OPERATING INSTRUCTIONS
24' 5"
7.4m
10'
3.05m
18' 8" (5.7 m)
10'
3.05m
4 - 8 Hrs
Two person
assembly
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
customerservice@kidkraft.com
canadacustomerservice@kidkraft.com
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
WARNING
often and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 24'5" x 24'5" (7.4 x 7.4 m) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6'6" (2 m)
24' 5"
7.4m
CAPACITY - 4 Users Maximum, Ages 3 to 7; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries,
day cares or parks
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
europecustomerservice@kidkraft.com
+31 20 305 8620 M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions
Table of Contents
Warnings and Safe Play Instructions . . . . . . . . . . pg. 2
Protective Surfacing Guidelines . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . pg. 4
About Our Wood – Limited Warranty . . . . . . . . . . pg. 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . pg. 6
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 7
Installation of I.D./Warning Plaque . . . . . . . . Final Step
9404061
Rev 09/17/2021
Advertisement
Related Manuals for KidKraft SUNVIEW II F24061
Summary of Contents for KidKraft SUNVIEW II F24061
- Page 1 Protective Surfacing Guidelines ....pg. 3 KidKraft, Inc. KidKraft Netherlands BV Instructions for Proper Maintenance ..pg. 4...
- Page 2 Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
- Page 3 Protective Surfacing - Reducing Risk of Serious Head Injury From Falls. One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.
- Page 4 Instructions for Proper Maintenance Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.
- Page 5 About Our Wood KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
- Page 6 Keys to Assembly Success Tools Required • Tape Measure • #1, #2 & #3 Phillips • Open End Wrench • 3/16” Hex Key • Carpenters Level or Robertson Bits (7/16”, 1/2” & 9/16”) • 8’ Step Ladder • Carpenters Square or Screwdriver •...
- Page 7 Wood Parts Identification (Reduced size) Nominal Actual Nominal Actual Size Size Size Size 1" x 6" 2 - Tarp Upright (2" x 3" x 47 3/4") 1" x 3 1/2" 5/8" x 5 3/8" " x 4" 2" x 6" 2"...
- Page 8 Wood Parts Identification (Reduced size) Nominal Actual Nominal Actual Size Size Size Size 1 - Roof Ridge (2" x 2" x 22-3/8") 1" x 6" 5/8" x 5 3/8" 1" x 3 1/2" " x 4" 3660106 2" x 6" 2"...
- Page 9 Hardware Parts Identification (Actual Size) (64) Flat Head Screw #8 x 1-1/2" (52042512) (2) Pan Screw #8 x 1/2" (9264504) (14) Flat Head Screw #8 x 2-1/2" (52042522) (2) Pan Screw #12 x 2" (9264620) (7) Flat Head Screw #8 x 3" (52042530) (4) Hex Bolt 1/4 x 1-1/2"...
- Page 11 Before you discard your cartons fill out the form below. • The carton I.D. stamp is located on the end of each carton. The tracking number is located on the KidKraft ID Plaque (9330355). • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department.
- Page 12 Step 1 Assemble Two Walls Using 1 Hex Bolt 5/16" x 4" (5/16" T-Nut, Washer and Lockwasher), HARDWARE LIST attach loosely leaving a gap between the Tarp Upright (2" x 3" x 47 3/4") and 2 Posts (5/4" x 4" x 79"). 2 pcs 5/16x4"...
- Page 13 Step 2 Assemble Floor Supports HARDWARE LIST Attach 4 T-Nuts 1/4" to the backs of the Floor Supports (5/4" x 4" x 39 1/2"). 4 pcs 1/4" T-Nut Using 2 Wood Screws (#8 x 3") per side attach the 4 pcs #8x3" Wood Screw SL Braces (2 x 3 x 15") to the Floor Supports (5/4"...
- Page 14 Attach Fort Walls and Tarp Upright Step 4 Take previously assembled Floor Supports and attach to both Uprights of the HARDWARE LIST previously assembled Walls using 2 Hex Bolts 1/4" x 3 1/2" (1/4" T-Nut, Flat Washer, and Lock Washer). 2 pcs 1/4x3-1/2"...
- Page 15 Step 5 Attach CE Access Boards, Floor Gussets Hold the CE Access Boards against the 2 Posts so that the lower CE HARDWARE LIST Access Boards are flush with the bottom of the Ground Sides, and the upper CE Access Board is flush with top of the Floor Support. 20 pcs #8x1-1/2"...
- Page 16 Assemble CE Floor and CE Rock Boards Step 6 Hold the CE Rock Board against the 2 Posts. HARDWARE LIST Make sure the CE Rock Boards are evenly spaced between the CE Access Boards, before proceeding to drill. Pre-drill with 1/8" drill bit using the holes 40 pcs #8x1-1/2"...
- Page 17 Step 7 Assemble Roof Using 2 Pan Bolts #8 x 3/8" and 2 #8 Lock Washers, connect HARDWARE LIST 2 L -Frame Brackets (1/2" x 12 1/4" x 22 3/4") together. Make sure that the bolts go in from opposite directions, as 2 pcs #8x1/2"...
- Page 18 Step 8 Assemble Swing End HARDWARE LIST Using 1 Hex Bolt 5/16" x 4 " (5/16" T-Nut, Washer, and Lock Washer), attach loosely leaving a gap between the Post SW (5/4" x 4" x 81") and the SW Post (2" x 4" x 80-1/2") as shown in the diagram below. 2 pcs 1/4x2"...
- Page 19 Step 9 Assemble Swing Hangers and Triangle Plate HARDWARE LIST Insert 4 Bolt Hangers with flat washers into the CE SW Rail (2" x 6" x 71") holes from the flush bottom edge of the beam, making sure that the Bolt Hangers are with the bottom of the CE SW Rail.
- Page 20 Step 10 Attach CE SW Rail to Swing End NOTE: For the next steps an adult helper may be needed. HARDWARE LIST Using 1 Hex Bolt 5/16" x 1 1/2" (5/16" T-Nut, Washer, and Lock Washer) and 1 Hex Bolt 5/16" x 3" 1 pc 5/16x3"...
- Page 21 Step 11 Attach Swing End to Fort HARDWARE LIST MOVE THE FORT TO FINAL LOCATION AND MAKE SURE GROUND AND FORT ARE LEVEL. Using 2 Hex Bolts 5/16" x 1 1/2" (5/16" T-Nut, Flat Washer, and Lock Washer) and 1 Hex Bolt 5/16" x 3" 1 pc 5/16x3"...
- Page 22 Step 12 Attach Ground Stakes and Slide WARNING! DIGGING CAN BE DANGEROUS. CHECK FIRST FOR HARDWARE LIST UNDERGROUND WIRING, CABLES, OR GAS LINES ETC. 2 pcs #12 x 2" Pan Screw •Use a scrap wood piece in between the top of the Ground Stake and the Sledge Hammer to protect the 8 pcs #8 x 2½"...
- Page 23 Step 13 Attach Swings, Rocks, Hole Plugs Using 4 Pan Bolts 1/4" x 1 1/4", (3/16" Flat Washer, 1/4" Lock Washer, and 1/4" Barrel Nut), attach 4 Rocks to the 4 ACCESSORY LIST Rock Boards. Make sure to use the correct holes in rocks. 4 pcs Rocks with hardware Note: The holes should be vertically aligned with the Pan Bolt on top and the Pan Screw on the bottom.
- Page 24 Final Step: Attach I.D. Plaque ATTACH THIS WARNING & I.D. PLAQUE TO A PROMINENT LOCATION ON YOUR PLAY EQUIPMENT! (Fort or Swing Post) This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model Attach with screws provided to a location...
- Page 25 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft https://prdregistration.kidkraft.com/ 4630 Olin Road Dallas, TX 75244 United States KidKraft would like to say Thank You for Attention: Customer Service your time and feedback.