Suspension Adjustments - BRP can-am MAVERICK MAX X MR 2023 Operator's Manual

W W A A R R N N I I N N G G
S S u u s s p p e e n n s s i i o o n n a a d d j j u u s s t t m m e e n n t t c c o o u u l l d d a a f f - -
f f e e c c t t v v e e h h i i c c l l e e h h a a n n d d l l i i n n g g . .
A A l l w w a a y y s s t t a a k k e e t t i i m m e e t t o o f f a a m m i i l l i i a a r r i i z z e e
y y o o u u r r s s e e l l f f w w i i t t h h t t h h e e v v e e h h i i c c l l e e ' ' s s b b e e h h a a v v - -
i i o o r r a a f f t t e e r r a a n n y y s s u u s s p p e e n n s s i i o o n n a a d d j j u u s s t t - -
m m e e n n t t h h a a s s b b e e e e n n m m a a d d e e . .
Choice of suspension adjustments
vary with vehicle load, personal pref-
erence, riding speed and terrain
condition.
The best way to set up the suspen-
sion, is to start from factory settings,
then customize each adjustment one
at a time.
Front and rear adjustments are inter-
related. It may be necessary to read-
just the rear shock absorbers after
adjusting front shock absorbers for
instance.
Test run the vehicle under the same
conditions; trail, speed, load, etc.
Change one adjustment and retest.
Proceed methodically until you are
satisfied.
Following are guidelines to fine-tune
suspension.
A A d d j j u u s s t t m m e e n n t t L L o o c c a a t t i i o o n n
T T Y Y P P I I C C A A L L - - W W I I T T H H O O U U T T R R E E B B O O U U N N D D D D A A M M P P I I N N G G
- - F F R R O O N N T T S S U U S S P P E E N N S S I I O O N N
1. Compression damping
2. Preload
3. Spring Crossover
T T Y Y P P I I C C A A L L - - W W I I T T H H O O U U T T R R E E B B O O U U N N D D D D A A M M P P I I N N G G
- - R R E E A A R R S S U U S S P P E E N N S S I I O O N N
1. Compression damping
2. Preload
3. Spring Crossover
S S u u s s p p e e n n s s i i o o n n F F a a c c t t o o r r y y S S e e t t t t i i n n g g s s
For adjustment procedures, refer to
Suspension Adjustments
section.
To adjust compression and rebound
to factory settings, proceed as follows:
1. Turn adjuster clockwise until it
stops.
2. Turn adjuster counterclockwise by
the specified amount, see table
below.
F F r r o o n n t t S S u u s s p p e e n n s s i i o o n n F F a a c c t t o o r r y y
S S e e t t t t i i n n g g s s
A A d d j j u u s s t t m m e e n n t t
Spring
preload
Compression
Damping
Crossover
ring position
TUNE YOUR RIDE
in
F F a a c c t t o o r r y y S S e e t t t t i i n n g g
67.5 mm
(2.657 in)
Position 2
52.3 mm
(2.059 in)
this
81