BRP can-am MAVERICK MAX X MR 2023 Operator's Manual page 72

EQUIPMENT
P P A A R R T T S S R R E E M M O O V V E E D D F F O O R R C C L L A A R R I I T T Y Y
1. Front anchor point
2. Rear anchor point
To install, reverse the removal instal-
lation, however pay attention to the
following.
Install seat using N N E E W W nuts. Tighten
to specification.
W W A A R R N N I I N N G G
U U s s e e n n e e w w n n u u t t s s w w h h e e n n i i n n s s t t a a l l l l i i n n g g s s e e a a t t
a a n n c c h h o o r r p p o o i i n n t t s s . .
T T i i g g h h t t e e n n i i n n g g T T o o r r q q u u e e
Rear anchor
point
Front anchor
point
S S e e a a t t H H e e i i g g h h t t A A d d j j u u s s t t m m e e n n t t
Seat height can be adjusted using the
anchor points. See Seat Removal and
Installation .
S S e e t t u u p p i i n n H H I I G G H H P P o o s s i i t t i i o o n n
Remove the seat cushion.
Remove both nuts securing the rear
anchor points.
Remove both nuts securing the front
anchor points.
Assemble both rear anchor points as
shown. Use N N E E W W nuts.
70
71 ± 15 Nm
(52 ± 11 lbf-ft)
28 ± 3.5 Nm
(20 ± 3 lbf-ft)
R R E E A A R R A A N N C C H H O O R R P P O O I I N N T T I I N N H H I I G G H H P P O O S S I I T T I I O O N N
1. Retaining nut
2. Seat frame
3. Sleeve
4. Vehicle frame
Install both front anchor points as
shown. Use N N E E W W nuts.
F F R R O O N N T T A A N N C C H H O O R R
P P O O S S I I T T I I O O N N
1. Retaining bolt
2. Seat support
W W A A R R N N I I N N G G
U U s s e e n n e e w w n n u u t t s s w w h h e e n n i i n n s s t t a a l l l l i i n n g g s s e e a a t t
a a n n c c h h o o r r p p o o i i n n t t s s . . E E n n s s u u r r e e b b o o t t h h a a n n - -
c c h h o o r r p p o o i i n n t t s s a a t t t t h h e e f f r r o o n n t t a a n n d d b b o o t t h h
a a n n c c h h o o r r p p o o i i n n t t s s a a t t t t h h e e r r e e a a r r a a r r e e s s e e t t
t t o o t t h h e e s s a a m m e e p p o o s s i i t t i i o o n n ( ( H H I I G G H H o o r r
L L O O W W ) ) b b e e f f o o r r e e r r i i d d i i n n g g t t h h e e v v e e h h i i c c l l e e . .
Tighten nuts to specification.
P P O O I I N N T T S S I I N N H H I I G G H H