BRP can-am MAVERICK MAX X MR 2023 Operator's Manual page 135

W W A A R R N N I I N N G G
R R e e p p l l a a c c e e t t i i r r e e s s o o n n l l y y w w i i t t h h t t h h e e s s a a m m e e
t t y y p p e e a a n n d d s s i i z z e e a a s s o o r r i i g g i i n n a a l l t t i i r r e e s s . .
F F o o r r u u n n i i d d i i r r e e c c t t i i o o n n a a l l t t r r e e a a d d p p a a t t t t e e r r n n , ,
e e n n s s u u r r e e t t h h a a t t t t h h e e t t i i r r e e s s a a r r e e i i n n s s t t a a l l l l e e d d
i i n n t t h h e e c c o o r r r r e e c c t t d d i i r r e e c c t t i i o o n n o o f f r r o o t t a a t t i i o o n n . .
T T i i r r e e s s s s h h o o u u l l d d b b e e r r e e p p l l a a c c e e d d , , b b y y a a n n
e e x x p p e e r r i i e e n n c c e e d d p p e e r r s s o o n n , , i i n n a a c c c c o o r r d d - -
a a n n c c e e w w i i t t h h t t i i r r e e i i n n d d u u s s t t r r y y s s t t a a n n d d a a r r d d s s
a a n n d d t t o o o o l l s s . .
T T i i r r e e M M o o u u n n t t i i n n g g o o n n B B e e a a d d l l o o c c k k W W h h e e e e l l s s
1. Mount the tire on wheel.
1. On the opposite side of bead-
lock, apply tire mounting lube
on inner bead of tire and wheel
to ensure proper seat when in-
flating. Mount the inner bead
over the wheel.
2. Seat tire outer bead in the
shoulder of the beadlock inner
ring and center the tire.
T T Y Y P P I I C C A A L L – – T T I I R R E E O O U U T T E E R R B B E E A A D D
1. Tire outer bead
2. Beadlock inner ring shoulder
2. Install all beadlock screws. To
avoid cross threading, start all
screws by hand.
N N O O T T I I C C E E
D D o o n n o o t t u u s s e e a a n n i i m m p p a a c c t t w w r r e e n n c c h h f f o o r r
i i n n s s t t a a l l l l i i n n g g b b e e a a d d l l o o c c k k s s c c r r e e w w s s . . T T h h e e
r r i i s s k k o o f f s s c c r r e e w w b b r r e e a a k k i i n n g g o o r r s s c c r r e e w w
s s t t r r i i p p p p i i n n g g i i s s h h i i g g h h w w h h e e n n u u s s i i n n g g a a n n
i i m m p p a a c c t t w w r r e e n n c c h h . .
MAINTENANCE PROCEDURES
1. Beadlock to be manually tightened
3. Tighten beadlock screws as per
following
sequence.
N N O O T T E E : :
To ensure even pressure on the bead-
lock clamp ring, tighten screws a a f f e e w w
t t u u r r n n s s a a t t a a t t i i m m e e .
T T i i g g h h t t e e n n i i n n g g T T o o r r q q u u e e
Beadlock
screws (FIRST
TORQUE)
T T Y Y P P I I C C A A L L - - T T I I G G H H T T E E N N I I N N G G S S E E Q Q U U E E N N C C E E
4. At this time check if the tire is still
centered on wheel. Reposition it if
necessary.
5. Tighten beadlock screws as per
the s s e e c c o o n n d d torque using the same
sequence.
specification
14 ± 1 Nm
(124 ± 9 lbf-in)
and
133