Cautions For Handling And Operation - Nakanishi COMBOX-NET.EIP Operation Manual

1 CAUTIONS FOR HANDLING AND OPERATION

 Read these warnings and cautions carefully and only use in the manner intended.
 These warnings and cautions are intended to avoid potential hazards that could result in personal injury or damage to
the device. These are instructions are classified as follows in accordance with the seriousness of the risk. Be sure to
observe warnings and cautions as they are all related to safety.
Class
A hazard that could result in bodily injury or damage to the device if the safety instructions are not
WARNING
properly followed.
A hazard that could result in light or moderate bodily injury or damage to the device if the safety
CAUTION
instructions are not followed.
NOTICE Be sure to keep the usage for your safety.
 The COMBOX-NET.EIP is an interface exclusively for controllers made by NAKANISHI. If the COMBOX-NET.EIP is
connected to machines other than the designated controller, the COMBOX-NET.EIP or connected devices might
malfunction.
 Before using the COMBOX-NET.EIP, carefully read this Operation Manuals regarding the correct connection, operation and
cautions. If the scanner is operated with insufficient understanding and knowledge, damage and/or malfunction to the
COMBOX-NET.EIP or controller may occur.
 Check the connected controller and the parameter settings, and match the parameter settings on the COMBOX-NET.EIP
to these settings. Failure to do so may cause a malfunction to occur.
 Carry the COMBOX-NET.EIP by holding the main body. Do not carry the COMBOX-NET.EIP by holding its cable. This
may damage the cable or cause the COMBOX-NET.EIP to malfunction.
 Never touch the cable or body of the COMBOX-NET.EIP with wet hands. This may cause an electric shock to the operator
or damage to the COMBOX-NET.EIP.
 Do not handle the cable connectors of the COMBOX-NET.EIP with wet or oily hands. This may cause malfunction due to a
poor connection.
 Never operate or handle the COMBOX-NET.EIP, controller or motor spindle until you have thoroughly read the Operation
Manual for each component, and safe operation has been confirmed.
 Before disconnecting the COMBOX-NET.EIP, controller or motor spindle, always turn the control power OFF and turn the
compressed air supply to the controller OFF. Then it is safe to remove the COMBOX-NET.EIP, controller and motor spindle.
 Do not use in dangerous environments. Protect the COMBOX-NET.EIP and controller from moisture and other
contaminants. Failure to protect the COMBOX-NET.EIP and controller may result in malfunction, fire or electric shock.
 Before connecting the COMBOX-NET.EIP to the controller with the cable connector, be sure to turn the controller OFF.
 When connecting the COMBOX-NET.EIP to the controller with the cable connector, securely tighten by the connector
screws. Loose screws may cause a malfunction.
 When connecting the COMBOX-NET.EIP to the terminal block on the machine by the cable terminals, tighten the terminal
screws at the specified tightening torque. Loose terminal screws may cause damage or malfunction on the COMBOX-
NET.EIP or the machine.
 Before connecting the COMBOX-NET.EIP to the terminal block on the machine by the cable terminals, make sure that the
terminals are not electrostically charged. Wiring the cable with the terminals electrostatically charged may cause the
COMBOX-NET.EIP or machine to malfunction as a result of the static electricity.
 Before handling the COMBOX-NET.EIP, adopt antistatic measures. Failure to do so may cause a malfunction to occur.
 Make sure that all input power sources are OFF before installation and wiring of this product to the machine. If the incoming
power source is ON, it may cause risk that leads to malfunction of the COMBOX-NET.EIP.
 Be sure to refer to the "Maintenance, Operation and Electrical Manuals" of the machine that is being interfaced to the
COMBOX-NET.EIP.
 Do not hit, drop or subject COMBOX-NET.EIP to any type of shock. Doing so may cause a malfunction.
 If an abnormality occurs on the COMBOX-NET.EIP or controller, an error is output and the motor spindle comes to a stop.
Remove the cause of the abnormality before resuming use.
 Avoid using the COMBOX-NET.EIP near machines that generate significant amounts of electrical noise. Failure to do so
may cause a malfunction to occur.
 When installing the COMBOX-NET.EIP, install on as level a location as possible subject to little impact.
 If smoke, noise or strange odors are emitted from the COMBOX-NET.EIP, immediately turn the power OFF.
Degree of Risk
！WARNING
！ CAUTION
44