Advertisement
Quick Links
A8079D (N2)
8/12
Copyright 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
PR100
with Aperio
Wireless Lock
Technology
Cylindrical Lock
Installation Instructions
™
Advertisement
Related Manuals for Sargent ASSA ABLOY PR100
Summary of Contents for Sargent ASSA ABLOY PR100
- Page 1 Wireless Lock Technology Cylindrical Lock Installation Instructions A8079D (N2) 8/12 Copyright 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
-
Page 2: Table Of Contents
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated... -
Page 3: General Description
PR100 Cylindrical Lock General Description The SARGENT ® PR100 lock with Aperio™ Technology makes it easy and cost-effective to bring access control to additional doors. It uses local wireless communication between the lock and an Aperio hub to connect to an access control system, eliminating the greatest cost and inconvenience of traditional access control, the wiring at the door. -
Page 4: Parts Breakdown
PR100 Cylindrical Lock Parts Breakdown 13.56 MHz iCLASS and 125 kHz Prox 1-800-810-WIRE • www.sargentlock.com • A8079D... - Page 5 PR100 Cylindrical Lock Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS (Continued) ITEM PART NO. DESCRIPTION QTY. Outside Lever Reference Cylindrical/10 Line Catalog For Available Levers Inside Lever Reference Cylindrical/10 Line Catalog For Available Levers 10-0453 Outside Escutcheon Assembly 10-0451 Inside Escutcheon Assembly 52-5292...
-
Page 6: Lock Installation
PR100 Cylindrical Lock Lock Installation 1 Prepare Door A. Verify Hand and Bevel of Door Stand on outside of locked door when determining door hand. LHRB RHRB Left Hand Left Hand Right Hand Right Hand Hinges Left Reverse Bevel Hinges Right Reverse Bevel Open Inward Hinges Left... - Page 7 PR100 Cylindrical Lock Centerline of Latch 2 Install Strike Front and Strike Install strike in the door frame (Fig.2). (2) #8-32 x 3/4" Latch Screws Fig. 2 3 Install Latchbolt 1. Install latch with beveled bolt facing the strike. 2. Attach with two screws but DO NOT tighten completely at this time. IMPORTANT: Latch bevel must match door bevel and deadlocking latch must stop on strike when door is closed.
- Page 8 PR100 Cylindrical Lock 5 Lock Adjustment Through-bolt Hole A. Lock Preset • Lock body holes: 12 and 6 o’clock (Fig. 5A). Outside of Door • Door thickness: 1-3/4” thick. Refer to adjustments below for other door conditions (Fig. 5B Detail). B.
- Page 9 PR100 Cylindrical Lock 7 Install Lock 1. Feed wires into the lock body hole from outside of door (Fig.7A). 2. Slide lock body into cross-bore hole from outside (locked side) of the door (Fig.7B). 3. Lock body must engage both the latch unit prongs and tail piece (Fig.
- Page 10 PR100 Cylindrical Lock 9 Install Door Position Switch (DPS) 1. Insert DPS into the raceway on the latch edge of the door. 2. Push wires through raceway toward lock prep. 3. Push DPS firmly into place by hand. Note: DO NOT TAP SWITCH WITH ANY TOOL. 4.
- Page 11 PR100 Cylindrical Lock 11 Escutcheon Wire Connections Inside of Door Images are shown without gasket. If gasket is necessary, refer to Step #10. Before the controller is Controller attached to the door: Reader 1. Attach the reader assembly Cable ribbon cable into the back of the controller assembly (side that faces towards the door when mounted) Fig.
- Page 12 PR100 Cylindrical Lock 13 Install Inside Escutcheon 1. Gently fold the excess ribbon connector into the ribbon-cable hole and DPS wires into DPS hole, being careful not to pinch wires (Fig. 13). 2. Insert (2) #8-32 x 2-1/4” screws through inside escutcheon and thread into outside escutcheon.
- Page 13 PR100 Cylindrical Lock 15 Install or Replace Batteries, Battery Keeper, and Cover 1. To install the batteries, first remove the battery cover using the security tool provided (Fig. 15C). 2. Unscrew the bottom screw of the battery keeper and remove the battery keeper, being careful not to break the tabs at top holding it in place.
-
Page 14: Operational Check
PR100 Cylindrical Lock Operational Check 1. Insert key into cylinder and rotate. There should be no friction against lock case, wire harness or any other obstructions. 2. Check that the key retracts the latch. The key should rotate freely. 3. Present a valid iCLASS or prox credential to unlock outside lever and retract latch. -
Page 15: Lock Led Indications
PR100 Cylindrical Lock Lock LED Indications 1 Lock Normal Operation LED indication The lock has three LEDs that support an optical scheme with red, yellow and green. The indication scheme is described by the figures below: Card read (configurable) One yellow flash (.25 seconds) Access granted, EAC offline or online One green flash (1 second) Access denied, EAC online... - Page 16 PR100 Cylindrical Lock 3 Lock Self Test LED Indication After replacing the battery, a Power On Self Test (POST) is performed. The result is indicated using a series of red and green LED flashes as is described by the figure below: One red, one green flash (1 second each) Good POST Bad POST...
- Page 17 Notes The global leader in door opening solutions...
- Page 18 New Haven, CT 06511 USA 800-810-WIRE (9473) • www.sargentlock.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets.