Table of Contents
Advertisement
[NUMBER OF REGISTERED
SIGNAL]
[COOLING CONDITION]
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE2 STATUS]
[AC VOLTAGE]
[LENS TYPE]
*2
[LENS ID]
*2
[LENS NAME]
*2
[LENS THROW RATIO]
[LENS ZOOM TYPE]
[ZOOM CALIBRATION]
[ON COUNT]
[OPERATING MODE]
[NORMAL]
[ECO]
[QUIET]
[USER1]
[USER2]
[USER3]
[CONSOLIDATED RUNTIME]
[UPGRADE KIT]
[SLOT]
[SIGNAL INFORMATION]
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
*2 This is displayed only when the standard DC motor unit installed in the Zoom Lens (Model No.: ET-D75LE6, ET-D75LE8, ET-D75LE10,
ET-D75LE20, ET-D75LE30, ET-D75LE40) is replaced with the stepping motor unit using the Stepping Motor Kit (Model No.: ET-D75MKS10),
or when a projection lens with the stepping motor is attached.
*3 [CONSOLIDATED RUNTIME] can be obtained with the following calculation formula. Values obtained by the calculation formula contain a
slight error.
A x 1.0 + B x 0.8
f A: Runtime of the light source with [OPERATING MODE] set to [NORMAL], [QUIET], [USER1], [USER2], or [USER3]
f B: Runtime of the light source with [OPERATING MODE] set to [ECO]
Chapter 4 Settings — [PROJECTOR SETUP] menu
Displays the number of registered signals.
Displays the set cooling conditions.
Displays the control status of the REMOTE2.
Displays the input supply voltage.
Displays the type name (type of the projection lens) set to the projection lens.
Displays the ID set to the projection lens.
Displays the name set to the projection lens.
Displays the range of the throw ratio supported by the projection lens.
*2
Displays the drive method of the zoom motor attached to the projection lens.
*2
Displays the zoom calibration result ([OK]/[FAILED]) and the calibration date.
*2
[POWER ON TIMES]
[MECHANICAL SHUTTER]
Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →
[OPERATING MODE].
Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].
Displays the runtime of the light source with [OPERATING MODE] set to [ECO].
Displays the runtime of the light source with [OPERATING MODE] set to [QUIET].
Displays the runtime of the light source with [OPERATING MODE] set to [USER1].
Displays the runtime of the light source with [OPERATING MODE] set to [USER2].
Displays the runtime of the light source with [OPERATING MODE] set to [USER3].
Converts the total runtime of the light sources with [OPERATING MODE] set to each item into the
time used with the [NORMAL] setting.
*3
The consolidated runtime is used for a rough indication about when to perform maintenance when the
projector is used in combination of each item in [OPERATING MODE].
[ET-NUK10]
Displays the product model number of the Function Board installed in <SLOT>.
Also, the firmware version is displayed after the product model number.
[INPUT]
[SIGNAL FORMAT]
[LINK]
[2D/3D]
[SIMUL]
[4K DIVISION]
[SAMPLING]
[BIT DEPTH]
[SIGNAL LEVEL]
[GAMMA]
[COLOR SPACE]
Conversion formula for [CONSOLIDATED RUNTIME]
Displays the number of times the power is turned on.
Displays the number of times the mechanical shutter is closed.
It is counted when [MECHANICAL SHUTTER] is set to [ENABLE].
Displays the activation status by the NFC Upgrade Kit (Model No.:
ET-NUK10).
Or, displays the status of the NFC function.
[ACTIVATED]: The NFC function can be used.
[NOT ACTIVATED]: The NFC function cannot be used.
Displays the input used for the projected image.
Displays the representative input terminal when one image is
displayed with multiple input signals.
Displays the format of the input signal.
Displays whether the input signal is a single link or quad link when
the image is displayed with SDI input.
Displays the determination results of the 2D/3D display.
Displays the [3D SIMUL INPUT SETTING] setting.
Displays the determination result of the signal when [AUTO] is set.
Displays the [4K DIVISION] setting.
Displays the determination result of the signal when [AUTO] is set.
Displays the sampling information and the color format of the input
signal.
Displays the gradation of the input signal.
Displays the signal level of the input signal.
Displays the [GAMMA] setting.
Displays the [COLOR SPACE] setting.
ENGLISH - 201
Advertisement
Table of Contents
