Scan & Charge Locking Function; Decommissioning The Product; Maintenance, Cleaning, Repair; Maintenance - Webasto Next Operating And Installation Instructions

15 | Decommissioning the product

If the vehicle does not automatically stop the charging
cycle:
Action
u
Stop charging cycle at
vehicle.
14.5 Scan & Charge locking function
You can enable or disable the wall-box locking function in the
Webasto Setup app or in the WebUI. If you want to restrict ac-
cess to the wall box for other users, disable "free charging" in
the Webasto Setup app.
The Webasto ChargeConnect app then offers the option of en-
abling individual charging processes via the two Scan & Charge
QR codes supplied, which are located under the protective film
on your charging station when it is delivered.
Instructions for charging in the locked state:
1. Connect the Webasto Next charging cable to the charge
port on your vehicle. In the locked state, a charging process
will not yet take place. The charging station shows a green
chase light (N6).
2. Scan one of the supplied Scan & Charge QR codes using
the corresponding function in the Webasto ChargeConnect
app. The charging process will be enabled and will start.
The charging station shows a pulsing blue light (N4).
3. After unplugging the charging cable at the end of the char-
ging process, free use is locked once more. For a further
charging process, repeat the steps.
NOTE
Green chase light running up and down
A green chase light on your charging station, which
runs up and down, signals locked status.
NOTE
Printing out additional Scan & Charge QR codes
If you need additional Scan & Charge QR codes, you
can print these out as described in chapter 4.1, "Print-
ing additional "Scan & Charge" QR codes" on page 6.
NOTE
Storing QR codes
You can keep your QR codes in your wallet or in the en-
trance area of your home to enable charging processes
in the locked state.
For more details see the Webasto ChargeConnect app (see
chapter 8, "Installation and electrical connection" on page 7).
15 Decommissioning the
product
Decommissioning shall be carried out only by a qualified electri-
cian.
1. Disconnect the power supply and vehicle charging line.
2. Remove the cover of the connection area in the wall box.
3. Disconnect the terminals and threaded cable connections.
4. Remove all connection lines and communication lines.
5. Remove the retaining screw on the underside of the wall
box.
6. Close the cover of the connection area in the wall box.
18 / 23
Description
Charging cycle is stopped. The
LED changes to a blue chase
light running up and down.
Operating status N5.
7. Lift the wall box of the mounting bracket.
Disposal: see chapter 18, "Disposal" on page 19.
16 Maintenance, cleaning,

repair

16.1

Maintenance

Maintenance must carried out by an electrician only, and in ac-
cordance with local requirements.
16.2

Cleaning

DANGER
High voltages.
Danger of fatal electric shock. Do not clean the char-
ging station with running water.
l Clean the installation only with a dry cloth. Do not use ag-
gressive cleaning agents, wax or solvents.
16.3 Repair
Unauthorised repair of the charging station is not permitted.
Webasto reserves the exclusive right to perform repairs to the
charging station. It is only permitted for repairs to be carried out
by an electrician using original spare parts sold by Webasto.
17 To replace the charging
cable
DANGER
Danger of fatal electric shock.
u
Switch off and secure the power supply to the char-
ging station.
NOTE
Only use genuine Webasto parts of the same power
level.
NOTE
The charging cable may be replaced a maximum of
four times during the service lifetime of the Webasto
Next.
NOTE
If you require spare parts, please contact your installer
or dealer.
See chapter 8.3.2, " Replace the charging cable" on page 10.
5111232C OI-II Webasto Next_EN