Timer Warning - JVC HR-DVS2EU Instructions Manual

IMPORTANT
Make sure the channel position number you wish
to record is displayed; if not, see "S
Setup" on page 67 and set the Guide Program
number for that S
If the number you entered is invalid, "ERROR" appears
on the screen and "Err" appears on the display panel.
Press and input a valid S
If the "GUIDE PROG SET" screen appears, see
"ATTENTION – Regarding Guide Program Number
Set" in the right column.
SET TAPE SPEED
5
Press SP/LP/EP (
It is not possible to select EP mode if "COLOUR
SYSTEM" is set to "MESECAM". (
(VHS deck only)
SET VPS/PDC MODE
6
Press VPS/PDC to select "ON" or "OFF".
If "VPS/PDC ON" is displayed on the screen or "VPS/
PDC" is lit on the display panel, VPS/PDC is set to ON.
If "VPS/PDC OFF" is displayed on the screen or "VPS/PDC"
is not lit on the display panel, VPS/PDC is set to OFF.
"VPS/PDC Recording" on page 37.
RETURN TO NORMAL SCREEN
7
Press PROG or OK. "PROGRAM COMPLETED" appears
on the screen for about 5 seconds, then normal screen
appears. If "PROGRAM OVERLAPPED" appears on the
TV screen and "Err" on the front display panel, see page
39.
Repeat steps 1 – 7 for each additional programme.
ENGAGE RECORDER'S TIMER MODE
8
Press ‰ (TIMER). The recorder turns off automatically
and ‰ appears on the display panel.
To disengage the timer, press ‰ (TIMER) again.
NOTES:
To Change The Stop Time . . .
. . . press STOP +/– in step 4. You can compensate for
anticipated programme schedule delays this way.
To Timer-Record Weekly Or Daily Serials . . .
. . . in step 4, press WEEKLY (NUMBER key "9") for weekly
serials or DAILY (NUMBER key "8") for daily serials (Monday
– Friday). Either "WEEKLY" or "DAILY" appears on the screen.
Pressing the button again makes the corresponding indication
disappear.
You can programme the VHS deck and the DV deck to timer-
record as many as 6 programmes each. If you try to programme
each deck to record a seventh, "PROGRAM FULL" appears on
screen and "FULL" appears on the front display panel. To record
the extra programme, you must first cancel any unnecessary
programmes ( pg. 38).
It is not possible to timer-record a TV programme with a
S V number which starts with "0".
HOW IEW
It is not possible to timer-record the same programme on both
the VHS deck and the DV deck simultaneously.
If the times that are programmed for recording on the DV
deck and on the VHS deck overlap, the earlier start time takes
precedence. If the start times are the same, the VHS deck
takes precedence.
V
HOW IEW
V number correctly.
HOW IEW
V number.
HOW IEW
) to set the tape speed.
pg. 17)
Satellite Receiver Users
To timer-record a satellite broadcast using the S
System system:
1
Perform "Satellite Receiver Control Setting" (
2
Perform steps 1 – 8. In step 4, the display panel shows
"L2" for the preset position. In step 6, you cannot set
"VPS/PDC" to "ON".
3
Leave the satellite receiver's power on.
ATTENTION
Regarding Guide Program Number Set
"GUIDE PROG SET" appears after performing step 3 if the
Guide Program number for the S
entered has not been set.
If you want to set the Guide Program number for the
satellite broadcast station, press the NUMBER key "0" to
change "TV PROG" to "SAT". Press %fi to input the
channel position number on which your recorder or
satellite receiver receives that station, then press OK or
to set the Guide Program Number. The S
Program screen appears.
GUIDE PROG SET
GUIDE PROG
[ 5 ∞] =
[PROG] : EXIT

Timer Warning

If you have programmed your
recorder to timer-record a
programme or a series of
programmes, a warning
appears on screen to tell you
that the recording is to start in
5 minutes.
NOTES:
The warning only appears if
you're not in the Timer mode at that time.
If this recorder is being used as the player for tape
dubbing, the warning screen is recorded on the tape in
the other video recorder.
The warning blinks for the entire 5 minutes leading up to
the start of timer recording. To clear the display, press
V
HOW
(Ex.) To timer-record a ZDF
programme with the
TV PROG
S V
HOW
2 – –
* If your recorder receives
ZDF on the channel
position 2, press OK or
[0] : SAT
after entering "2".
35
EN
V
HOW IEW
pg. 13).
number you
IEW
#
V
HOW IEW
system.
IEW
#
– WARNING–
TIMER RECORDING
TO START SOON
[ ]
.